PO.FRAC.Design.UFD
Description
The optimum fracture for a given mass of proppant, by unified fracture design (UFD). The proppant mass that reaches the pay sets the proppant number Np = 2·kf·Vprop/(k·Vres), and the proppant number alone fixes the dimensionless fracture conductivity CfD that gives the largest pseudo-steady-state productivity index JD. The function returns the proppant number, the optimum CfD, that largest JD, and the half-length and propped width that realise it. A design whose CfD is far from the optimum is either a bottleneck (CfD well below it: too long and narrow) or too short and wide (well above it).
Formula
=LAMBDA(mass, rho_p, phi_p, kf, k, h, hf, xe, output, IF(OR(mass<=0, rho_p<=0, phi_p<0, phi_p>=1, kf<=0, k<=0, h<=0, hf<=0, xe<=0), NA(), LET(
vbulk, mass/((1-phi_p)*rho_p), vpay, vbulk*MIN(1, h/hf), np, 2*kf*vpay/(k*xe^2*h), lnp, LN(np), cfd, IF(np<=0.1, 1.6, IF(np<=10, 1.6+EXP((-0.583+1.48*lnp)/(1+0.142*lnp)), np)), jd, IF(np<=0.1, 1/(0.99-0.5*lnp), 6/PI()-EXP((0.423-0.311*np-0.089*np^2)/(1+0.667*np+0.015*np^2))), xf, SQRT(kf*vpay/2/(cfd*h*k)), IF(output="Np", np, IF(output="CfD", cfd, IF(output="JD", jd, IF(output="xf", xf, IF(output="w", 12*vpay/2/(xf*h), NA()))))))))Parameters
| Parameter | Unit | Description |
|---|---|---|
mass |
lbm | Proppant mass placed, both wings |
rho_p |
lb/ft³ | Proppant grain (particle) density |
phi_p |
fraction | Porosity of the proppant pack |
kf |
mD | Effective permeability of the proppant pack, already reduced for damage |
k |
mD | Formation permeability |
h |
ft | Net pay thickness |
hf |
ft | Fracture height; the pay's share of the proppant is h/hf (1 when hf ≤ h) |
xe |
ft | Side of the square drainage area |
output |
text | "Np" (proppant number), "CfD" (optimum dimensionless conductivity), "JD" (largest dimensionless productivity index), "xf" (optimum half-length, ft) or "w" (propped width at the optimum, in) |
Examples
| Invocation | Expected |
|---|---|
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 5, 50, 50, 4000, "Np") |
0.02 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 5, 50, 50, 4000, "CfD") |
1.6 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 5, 50, 50, 4000, "xf") |
220 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 5, 50, 50, 4000, "JD") |
0.339442 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 200, 50, 50, 4000, "Np") |
0.0005 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 200, 50, 50, 4000, "xf") |
35 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 200, 50, 50, 4000, "JD") |
0.21 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 5, 50, 50, 4000, "w") |
0.429325 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 5, 50, 100, 4000, "Np") |
0.01 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 0.999, 50, 50, 4000, "JD") |
0.467 |
=PO.FRAC.Design.UFD(79200, 165, 0.4, 50000, 0.01, 50, 50, 4000, "CfD") |
10 |
=IF(ISNA(PO.FRAC.Design.UFD(0, 165, 0.4, 50000, 5, 50, 50, 4000, "Np")), 1, 0) |
1 |