SCAL Tables Export for SWOF and SGOF


Description

What SWOF and SGOF tables do a rock's Corey water-oil and gas-oil models give for a simulator deck? You enter the two models' endpoints and exponents. You read off both tables, each with a keyword column to paste into an Eclipse or OPM Flow deck's PROPS section, and three checks of what a simulator demands: saturations that rise, monotonic kr, tables that start and end at their endpoints, and SGOF's Krog at Sg = 0 equal to SWOF's Krow at connate water. A chart beside each table draws its curves.

Parameters:

  • Water-oil model: connate water STX_Swi, residual oil to water STX_Sorw, Krow at Swi STX_KroEnd, Krw at Sorw STX_KrwEnd, and the Corey exponents STX_No and STX_Nw
  • Gas-oil model: critical gas saturation STX_Sgc (above 0), residual oil to gas at Swi STX_Sorg, Krog at Sg = 0 STX_KrogEnd, Krg at Sorg STX_KrgEnd, and the exponents STX_Nog and STX_Ng
  • Check limit: the largest gap accepted between Krog at Sg = 0 and Krow at Swc, STX_KrTol (0.001)

How to use it: type the exponents and endpoints the Relative Permeability Fit sheet gives for your points, or a SCAL report's, and copy each keyword column from its keyword line to its closing slash. The capillary pressure columns are zero; for a transition zone, put the drainage Pc in psi at each saturation in the Pcow column (the Capillary Pressure Models Comparison sheet gives it), falling with Sw.

Method:

  • SWOF. Sw = Swc + Sw*·(1 − Swc − Sorw) for Sw* = 0, 0.1, … 1, so from the connate water saturation to 1 − Sorw in tenths of the mobile range, then Sw = 1. Krw = Krw@Sorw·Sw*^Nw and Krow = Krow@Swi·(1 − Sw*)^No by the catalog's Corey functions. The functions take Sw from Swi to 1 − Sorw, so the Sw = 1 line reads them at 1 − Sorw: Krw held at its endpoint and Krow 0.
  • SGOF. With the gas-oil system's connate liquid Slc = Swc + Sorg, Krg = Krg@Sorg·((Sg − Sgc)/(1 − Sgc − Slc))^Ng and Krog = Krog@0·((1 − Sg − Slc)/(1 − Slc))^Nog, Corey in the cells, each normalised saturation clamped to 0 to 1, as the Stone Three-Phase Relative Permeability sheet writes them. The lines are Sg = 0, then Sgc to 1 − Slc (1 − Swc − Sorg) in tenths, then 1 − Swc with Krg held.
  • Keyword text. Each line joins the saturation to four places, the two kr to five and the Pc to one with FIXED(x, n, TRUE); the keyword, a column comment, the lines and a closing slash fill the text column.
  • Checks. SWOF: a FAIL for Swi + Sorw of 1 or more, a saturation that fails to rise, a Krw that falls or a Krow that rises down the table, or a table that doesn't start at Krw = 0 and end at Krow = 0. SGOF: the same for Sg, Krg and Krog, starting at Sg = 0 with Krg = 0 and ending at Krog = 0; a zero Sgc repeats Sg = 0 and fails. Consistency: Krog at Sg = 0 within the check limit of Krow at Swc, since a simulator takes both as the oil's kr at connate water (and SGOF ends at 1 − Swc by construction).

Example: The defaults are the rock the SCAL sheets share: a water-wet sandstone with Swi 20 %, Sorw 25 %, Sorg 10 %, Sgc 5 %, Krow@Swi 1, Krw@Sorw 0.35, Krg@Sorg 0.40, and Corey exponents No 2.5, Nw 2, Nog 2.5 and Ng 2. They are the model the Relative Permeability Fit sheet recovers from its points: 1.99 and 2.51 through the measured endpoints. SWOF runs from 0.2000 (Krw 0, Krow 1) to 0.7500 (Krw 0.35, Krow 0) and closes at 1.0000 with Krw 0.35. Halfway, at Sw = 0.4750, the line reads 0.4750 0.08750 0.17678 0.0. SGOF runs from Sg = 0 (Krg 0, Krog 1) through 0.0500 (Krog 0.83088) to 0.7000 (Krg 0.40, Krog 0) and closes at 0.8000; halfway, at Sg = 0.3750, it reads 0.3750 0.10000 0.14688 0.0.

Functions used

PO.SCAL.Corey.Krw(Sw, Swi, Sorw, Krw_Sorw, Nw)

Calculates Corey-type water relative permeability, [fraction].

PO.SCAL.Corey.Krow(Sw, Swi, Sorw, Krow_Swi, No)

Calculates Corey-type oil relative permeability, [fraction].

Names (39)

NameRefers toComment
STX_Swi $B$4 Connate water saturation, Swc = Swi, %
STX_Sorw $B$5 Residual oil saturation to water, Sorw, %
STX_KroEnd $B$6 Krow at Swi, frac
STX_KrwEnd $B$7 Krw at Sorw, frac
STX_No $B$8 Oil exponent, No
STX_Nw $B$9 Water exponent, Nw
STX_Sgc $B$11 Critical gas saturation, Sgc (above 0), %
STX_Sorg $B$12 Residual oil saturation to gas at Swi, Sorg, %
STX_KrogEnd $B$13 Krog at Sg = 0 (Krow at Swi), frac
STX_KrgEnd $B$14 Krg at Sorg, at Sg = 1 − Swi − Sorg, frac
STX_Nog $B$15 Oil exponent in the gas-oil system, Nog
STX_Ng $B$16 Gas exponent, Ng
STX_KrTol $B$18 Largest gap accepted between Krog at Sg = 0 and Krow at Swc, frac
STX_Inputs $B$4:$B$18 The water-oil endpoints and Corey exponents, the gas-oil endpoints and exponents, and the endpoint-consistency tolerance
STX_Mobile $B$21 Mobile oil saturation to water, 1 − Swi − Sorw, %
STX_Slc $B$22 Connate liquid of the gas-oil system, Slc = Swi + Sorg, %
STX_SgMax $B$23 Gas saturation where Krog reaches 0, 1 − Slc, %
STX_SgLast $B$24 Last gas saturation of SGOF, 1 − Swc, %
STX_KrowFirst $B$25 SWOF Krow at Swc, the first line, frac
STX_KrwMax $B$26 SWOF Krw at the last line, frac
STX_KrogFirst $B$27 SGOF Krog at Sg = 0, the first line, frac
STX_KrgMax $B$28 SGOF Krg at the last line, frac
STX_SwofCheck $B$29 SWOF check verdict
STX_SwofCheckNote $C$29 SWOF check comment
STX_SgofCheck $B$30 SGOF check verdict
STX_SgofCheckNote $C$30 SGOF check comment
STX_EndCheck $B$31 Endpoint consistency check verdict
STX_EndCheckNote $C$31 Endpoint consistency check comment
STX_Results $B$21:$B$31 The mobile oil saturation, the gas-oil system's connate liquid, the gas saturations where Krog reaches 0 and where SGOF ends, the tables' first Krow and Krog and last Krw and Krg, and three checks
STX_SwofSw $A$41:$A$52 SWOF saturations
STX_SwofKrw $B$41:$B$52 SWOF Krw
STX_SwofKrow $C$41:$C$52 SWOF Krow
STX_SwofText $E$39:$E$53 SWOF keyword text, copy-ready
STX_SwofMid $E$46 SWOF line at the middle of the mobile range, Sw* = 0.5
STX_SgofSg $A$60:$A$72 SGOF saturations
STX_SgofKrg $B$60:$B$72 SGOF Krg
STX_SgofKrog $C$60:$C$72 SGOF Krog
STX_SgofText $E$58:$E$73 SGOF keyword text, copy-ready
STX_SgofMid $E$66 SGOF line at the middle of the mobile gas range

Details

Inserts73 rows × 5 columns
CategorySpecial Core Analysis
For agents and tools Descriptor (.md)
Tags:
SCALCoreyrelative-permeabilitySWOFSGOFEclipseOPMsimulation-inputsaturation-functions

Need a custom calculation? Request a Blueprint