---
id: po.wb.res.waterflood-design
title: Waterflood Design
summary: "How much oil a layered five-spot waterflood recovers at an economic WOR, from a Corey fit to SCAL data through fractional flow to vertical sweep."
category: Reservoir
requires:
  - excel-365
tags:
  - waterflood
  - relative-permeability
  - fractional-flow
  - dykstra-parsons
  - stiles
  - sweep
---

## Description

How much oil will a waterflood in a layered five-spot recover by the time the water-oil ratio reaches its economic limit? You enter the SCAL points and endpoints, the oil and water viscosities, the layer permeabilities and thicknesses, the pattern and the economic WOR. You read off the Corey exponents, the fractional-flow shock and breakthrough, the Dykstra-Parsons and Stiles vertical sweep, and the oil recovered and recovery factor at the economic WOR. Field units.

**How to use it:** Enter the SCAL relative-permeability points and the measured endpoints on the Fit sheet and choose whether the fit holds the measured endpoints or fits them freely. Enter the oil and water viscosities on the Flow sheet and check the Welge tangent touches the fractional-flow curve. Enter the layers in depth order, the pattern area, porosity, formation volume factors and the economic surface WOR on the Sweep sheet. The Summary links the results and every check. The examples are synthetic; replace the SCAL and layer tables with measured data.

**Method:** The Fit sheet regresses ln krw against ln Sw* and ln kro against ln(1 − Sw*), with Sw* = (Sw − Swi)/(1 − Swi − Sorw) the normalised saturation, both freely and through the measured endpoints, for krw = krw° Sw*^nw and kro = kro° (1 − Sw*)^no; the default uses the measured endpoints. The Flow sheet applies the selected fit and viscosities to the Buckley-Leverett fractional flow fw = 1/(1 + (kro μw)/(krw μo)), finds the shock front by the Welge tangent, and gives the endpoint mobility ratio M = (krw°/μw)/(kro°/μo) and the displacement efficiency ED = (1 − Swi − Sorw)/(1 − Swi). The Sweep sheet applies Dykstra-Parsons and Stiles to the same endpoints, viscosities and saturations, interpolating between layer breakthroughs in log surface WOR. The oil in place is N = 7758 A h φ (1 − Swi)/Bo. Recovery is N × ED × vertical coverage × Craig's five-spot areal sweep at breakthrough, a correlation in M.

The layer-breakthrough PVI is the reservoir water injected over the pore volume of the idealised vertically layered flood (before areal scaling), not a whole-pattern material-balance PVI. For equal-thickness layers it is the mobile saturation times the mean of each layer's swept fraction plus the water injected after its breakthrough; for a layer already broken through, that is (M + 1)/2 × (k/k_break − 1). This is not a calendar-time forecast. The chart uses the same constant breakthrough areal sweep for every recovery point and for the economic point; it is an approximation, not a time-varying areal model.

**Example:** The shared synthetic SCAL rock has Swi 0.20, Sorw 0.25, and measured oil and water endpoints 1 and 0.35. With oil and water viscosities 5 and 0.5 cp, the endpoint mobility ratio is 3.5. Ten 5 ft layers in a 40-acre pattern (the classic Dykstra-Parsons example layers) on this rock, at an economic surface WOR of 20, give a vertical coverage of 0.6965 and an estimated recovery of 541,240 STB, 26.16% of the 2,068,800 STB initially in place. These are synthetic design inputs, not the layer example's original fluid and rock case.

## Validity

Fractional flow is a one-dimensional Buckley-Leverett shock solution; Dykstra-Parsons and Stiles are separate no-crossflow, piston-displacement layer models, not a coupled fractional-flow forecast. Dykstra-Parsons and its PVI progression assume equal layer thickness and uniform porosity; Stiles accepts unequal thickness. Craig's areal sweep is a five-spot breakthrough correlation and need not hold for other geometries or at later times. An economic WOR outside the breakthrough range uses the nearest endpoint for recovery, injected PV and water cut, and warns; it is not extrapolated. Craig's raw areal sweep is checked for the physical interval from zero to one. A value outside that interval fails the check and sets the recovered oil and plotted recovery to zero; the zero is not a forecast. A free fit can imply an endpoint above one; this warns and stops the downstream calculations. Use measured SCAL, PVT and representative layer data, check mobility and geometrical applicability, and use simulation where crossflow, gravity or complex pattern geometry matters.

## References

- Buckley, S.E. and Leverett, M.C. (1942). Mechanism of Fluid Displacement in Sands. *Transactions of the AIME*.
- Stiles, W.E. (1949). Use of Permeability Distribution in Water Flood Calculations. *Transactions of the AIME*.
- Dykstra, H. and Parsons, R.L. (1950). *The Prediction of Oil Recovery by Waterflood*.
- Craig, F.F. (1971). *The Reservoir Engineering Aspects of Waterflooding*. SPE Monograph 3.

## Inputs

| Input | Unit | Default | Name |
|---|---|---|---|
| Irreducible water saturation | fraction | 0.20 | `WGF_Swi` |
| Residual oil saturation | fraction | 0.25 | `WGF_Sorw` |
| Measured oil endpoint | fraction | 1 | `WGF_KroEnd` |
| Measured water endpoint | fraction | 0.35 | `WGF_KrwEnd` |
| Endpoint model (Measured or Free) | text | Measured | `WGF_Pick` |
| Oil viscosity | cp | 5 | `WGFLOW_MuO` |
| Water viscosity | cp | 0.5 | `WGFLOW_MuW` |
| Oil formation volume factor | rb/STB | 1.2 | `WGS_Bo` |
| Water formation volume factor | rb/STB | 1.02 | `WGS_Bw` |
| Five-spot pattern area | acres | 40 | `WGS_Area` |
| Porosity | fraction | 0.2 | `WGS_Phi` |
| Economic surface WOR | STB/STB | 20 | `WGS_WorEc` |

The SCAL points on the Fit sheet and the layer permeabilities and thicknesses on the Sweep sheet are editable tables.

## Sheets

- `Guide` — the workflow and how to read the separate models.
- `Fit` — the measured endpoints and the endpoint model; Corey exponents fitted freely and through the measured endpoints, the fit quality, the selected model, and the synthetic lab points against it.
- `Flow` — the rock and fit linked from Fit with the viscosities; the mobility ratio, shock-front saturation and water cut, the average saturation, pore volumes injected and recovery at breakthrough, the displacement efficiency, and the fractional-flow curve with its Welge tangent.
- `Sweep` — the pattern, fluids and layers; the permeability variation, oil in place, Craig's areal sweep, the Dykstra-Parsons coverage and Stiles sweep at the economic WOR, the oil recovered, and the breakthrough progression with recovery and water cut against injected pore volumes.
- `Summary` — the breakthrough and economic-WOR results linked from the sheets and every check under one verdict.
- `Test Cases` — the worked example and other cases, with expected and computed results.

## Functions used

Catalog LAMBDAs `PO.RES.Waterflood.FractionalFlow`, `PO.RES.Waterflood.DykstraParsons`, `PO.RES.Waterflood.Stiles` and `PO.RES.Vol.STOIIP`.
