---
id: po.wb.pta.buildup-interpretation
title: Buildup Interpretation
summary: "What permeability, skin and p-star an oil buildup gives and whether it sees a fault, from gauge QC and the Bourdet derivative to Horner and the late slope."
category: Reservoir
requires:
  - po-addin
  - excel-365
tags:
  - pressure-transient-analysis
  - buildup
  - Bourdet
  - Horner
  - radial-flow
  - permeability
  - skin
  - sealing-fault
  - constant-pressure
  - wellbore-storage
  - pseudo-pressure
---

## Description

What permeability, skin and p-star does this oil buildup give, and does it see a boundary? You enter the rate before shut-in, the cumulative oil, the rock and fluid properties and the flowing pressure at shut-in, and paste the gauge's shut-in times and pressures. The Bourdet derivative picks the radial-flow (IARF) window, a Horner line through it gives k, skin and p-star, and the late slope reads a sealing fault or a constant-pressure boundary and the distance to a fault. Field units; time in hours.

**How to use it:** Set q, Np and the rock and fluid properties on the Test sheet. Paste 37 positive, increasing times and pressures into A39:B75 and type the measured flowing pressure at shut-in over its model default. Leave the derived columns as formulas; changing the row count requires resizing every dependent range. Check the gauge calibration, rate stability and the derivative on the Diagnostic sheet before accepting the IARF window, then read k, skin and p-star on the Horner sheet and the late signature on the Boundary sheet. The model k, skin, pi, C and distance generate reference curves only: disregard the model round-trip checks for field data and estimate C from the early unit-slope data. The Summary is last and lists every check.

**Method:** Producing time is 24,000 Np/q for Np in MSTB; the Horner ratio is (tp+dt)/dt and the Agarwal equivalent time te = tp/ratio. The Bourdet derivative is d(pws-pwf)/d ln(te); multiply by LN(10) for a per-decade slope. After the storage hump, select the first connected flat run spanning at least 0.5 log10 cycle within a 10% band, and fit pws against log10(ratio) only there. Permeability is 162.6 q Bo mu/(m h); skin uses the line's one-hour pressure and the flowing pressure at shut-in; p-star is the line at ratio one. Fit the last half log cycle separately: a late/early slope ratio within 20% of two supports one sealing fault; below 0.9 supports a constant-pressure roll-over. The two lines' crossing time and the interpreted k give the fault distance. The model validation fits a Miller-Dyes-Hutchinson (MDH) line to a model drawdown and checks storage and test design. The Gas sheet integrates 2p/(mu Z) for the pseudo-pressure.

**Example:** The PTA reference oil well: q = 250 STB/d, Bo = 1.25 bbl/STB, mu = 1 cP, phi = 0.2, ct = 1.5e-5/psi, rw = 0.354 ft, h = 30 ft, model k = 50 mD, skin = 5, pi = 5,000 psi, C = 0.001 bbl/psi, with Np = 2.5 MSTB (tp = 240 h), a fault 200 ft away and 37 gauge points. The IARF window runs from 0.422 to 4.217 h, m = 35.5552 psi/cycle, k = 47.6371 mD, skin = 4.489 and p-star = 4,962.91 psi; the late line has m = 65.0092, a slope ratio of 1.8284, and puts the fault 180.11 ft away. These are synthetic, not field measurements. Every result matches the source calculations on identical inputs to 1e-9, including Horner on this grid. The Gas sheet keeps its source's 3,000 psia, 160 F, SG = 0.7 sweet-gas reference.

## Validity

Homogeneous radial, single-phase flow with constant fluid properties, storage and skin, and one pre-shut-in rate or its Np/q equivalent. Variable rates need superposition (the DST and multi-rate workbook). Fractures, multiphase flow, dual porosity and multiple boundaries can mimic these signatures. Inspect the window: a storage tail can bias it. A finite test approaches slope doubling slowly; the default fault estimate is about 10% short. The early line's p-star need not equal the initial pressure. Use the distance only for a supported sealing-fault signature; an unresolved boundary is not proof of infinite-acting flow. Model and type curves are not another field gauge. The Gas sheet is only a 16-point m(p) lookup for a separate gas fluid, not a gas k or skin interpretation and never an interpretation of the oil gauge.

Named alternatives: nonlinear whole-record fitting and dual-porosity matching, for which the add-in has no functions. A full two-rate gas buildup, pseudo-time and inverse m(p) are left out here for size.

## References

- Horner, D.R. (1951). Pressure Build-up in Wells. Proc. Third World Petroleum Congress, The Hague, Sec. II, 503-523.
- Miller, C.C., Dyes, A.B. and Hutchinson, C.A. (1950). The Estimation of Permeability and Reservoir Pressure from Bottom Hole Pressure Build-up Characteristics. *Trans. AIME* 189, 91-104.
- Gray, K.E. (1965). Approximating Well-to-Fault Distance from Pressure Build-up Tests. *JPT* 17(7), 761-767.
- Earlougher, R.C. (1977). *Advances in Well Test Analysis*. SPE Monograph 5.
- Agarwal, R.G. (1980). A New Method to Account for Producing Time Effects When Drawdown Type Curves Are Used to Analyze Pressure Buildup and Other Test Data. SPE-9289-MS.
- Al-Hussainy, R., Ramey, H.J. and Crawford, P.B. (1966). The Flow of Real Gases Through Porous Media. *JPT* 18(5), 624-636.
- Bourdet, D., Ayoub, J.A. and Pirard, Y.M. (1989). Use of Pressure Derivative in Well-Test Interpretation. *SPE Formation Evaluation* 4(2), 293-302. SPE-12777-PA.

## Inputs

| Input | Unit | Default | Name |
|---|---|---|---|
| Rate before shut-in | STB/d | 250 | `BT_q` |
| Cumulative oil produced | MSTB | 2.5 | `BT_Np` |
| Oil formation volume factor | bbl/STB | 1.25 | `BT_Bo` |
| Oil viscosity | cP | 1 | `BT_mu` |
| Porosity | fraction | 0.2 | `BT_phi` |
| Total compressibility | 1/psi | 0.000015 | `BT_ct` |
| Wellbore radius | ft | 0.354 | `BT_rw` |
| Net pay | ft | 30 | `BT_h` |
| Flowing pressure at shut-in | psi | model | `BT_Pwf` |
| Shut-in times and pressures (gauge) | h, psi | model, 37 points | `BT_dt`, `BT_Build` |
| Bourdet smoothing window | natural-log cycles | 0.2 | `BT_L` |
| IARF derivative flat within | fraction | 0.1 | `BT_Flat` |
| IARF and late line span | log10 cycles | 0.5 | `BT_Span` |
| Model permeability | mD | 50 | `BT_ModelK` |
| Model skin | — | 5 | `BT_ModelS` |
| Initial reservoir pressure | psi | 5000 | `BT_Pi` |
| Storage coefficient | bbl/psi | 0.001 | `BT_C` |
| Boundary distance | ft | 200 | `BT_Lb` |
| Model: 0 infinite, 1 fault, 2 const P | choice | 1 | `BT_Case` |
| Fault slope band around two | fraction | 0.2 | `BBY_RTol` |

## Sheets

- `Guide` — how to use the workbook, model against field data, and the reduced gas appendix and alternatives.
- `Test` — the shared test, rock, fluid and synthetic model inputs, the producing time and model flowing pressure, and the pasted gauge record with its derivative audit columns.
- `Diagnostic` — the actual buildup and its Bourdet derivative on equivalent time, the IARF window, and a separate model-only drawdown with an MDH validation fit.
- `Horner` — the Horner line through the derivative-selected IARF window only, with permeability, skin and p-star.
- `Boundary` — the late slope against the IARF slope: fault doubling or constant-pressure roll-over, and the approximate fault distance.
- `Storage` — the model-only storage and skin type curve and the test design: duration, radius of investigation and gauge resolution.
- `Gas` — a separate sweet-gas reference and its 16-point pseudo-pressure table and m(p) curve.
- `Summary` — every headline and every check.
- `Test Cases` — the worked example and other cases, with expected and computed results.

## Functions used

`PO.PTA.Pw.VW`, `.LinSealF`, `.LinConP`; `PO.PTA.PD.VW`; `PO.PTA.ToDim.CD`, `.tD`; `PO.PTA.Horner.Ratio`, `.k`, `.S`, `.Pstar`; `PO.DCA.Diag.Bourdet.SemiLog`; `PO.PTA.MDH.Fit`; `PO.IPR.Rwa`; `PO.PTA.Design.Duration`, `.Rinv`, `.GaugeRes`; `PO.PVT.PseudoP`; `SLOPE`, `RSQ`, `SUMPRODUCT`, `INDEX`, `MATCH`, `FILTER`, `COUNTIF`. The gas LAMBDA supplies its PVT dependencies.
