---
id: po.wb.pp.saturation-height
title: Saturation-Height Model
summary: "What water saturation each rock type holds at each height above the free-water level, from one Leverett-J fit per rock type, and the oil in place."
category: Petrophysics
requires:
  - po-addin
  - excel-365
tags:
  - petrophysics
  - saturation-height
  - saturation
  - capillary-pressure
  - transition-zone
  - Leverett-J
  - Archie
---

## Description

What water saturation does each rock hold at each height above the free-water level, and how much oil is that? Between wells, and in a model where there is no log, the answer is a saturation-height function. You enter the log's transition zone, the core plugs of each rock type, the fluids and the free-water level. You read off one Leverett-J fit per rock type, the water saturation by height from each, the height at which each reaches a chosen saturation, and the oil in place over the column.

**How to use it:** Enter Archie's parameters, the gamma-ray picks, the free-water level (from pressure gradients, not from the deepest oil on the log), the reservoir fluids and the core porosity-permeability transform on the Log Fit sheet, and paste the transition zone's depth, gamma ray, bulk density and deep resistivity below them. Enter the plugs of each rock type, their laboratory fluids and the irreducible water on the Rock Types sheet; each rock type is fitted on its own rows, so never mix rock types in one fit. Read the saturation against height on the Sw by Height sheet. Enter the column's area and oil formation volume factor, and the lab curve's Brooks-Corey parameters, on the Volumes sheet. Resolve every check on the Summary.

**Method:** Height above the free-water level h = FWL - depth. One psi of reservoir capillary pressure holds water up 144/(rho w - rho o) ft, so Pc = h divided by that. The J of a sample is 0.2166 Pc/(sigma cos theta) times the square root of k/phi, at its density porosity and the permeability the core transform gives it. The log fit is a power law Sw = a J^b, a straight line fitted on ln Sw against ln J, with the scatter as the RMS of the fitted minus the logged Sw. Each core rock type's fit is the same power law on that rock type's own plug points. The reference J curve J = a Sw*^b, fitted over all thirteen plugs, is what scales plug A's capillary pressure to rock B. The height at which a chosen saturation is reached comes back through the Leverett capillary pressure and the height conversion. The lab curve is a Brooks-Corey capillary pressure, Pc = Pd Sw*^(-1/lambda). The oil in place over the column is 7758 times the area, the porosity, the band height and the mean hydrocarbon saturation of the band, over the oil formation volume factor.

**Example:** The log's own fit, over the clean oil sand's transition zone from 5,014 to 5,048 ft above a free-water level at 5,050 ft: a power law Sw = a J^b with b = -0.5859 and a = 0.2832, an R-squared of 0.9771 and an RMS scatter of 0.0357 saturation units. Rock 1 (1,000 mD) reaches the reported 20 % water saturation 27.99 ft above the FWL, rock 2 (100 mD) at 79.25 ft and rock 3 (10 mD) at 217.40 ft; rock 1 still holds 0.0949 water at 100 ft above the FWL.

The scaling of plug A to rock B is Ahmed's Example 4-7: a scale factor of 0.8898, a reference J curve of a = 0.0498 and b = -0.6765 at an R-squared of 0.9961, and rock B's capillary pressure of 0.898 psi at 40 % water saturation against plug A's 1.009 psi.

The three core rock types are fitted on their own plugs, each on its normalised saturation Sw* = (Sw - Swi)/(1 - Swi), so each curve flattens at the irreducible water instead of falling through it: rock type 1 (plug A, five points) b = -1.4684 and a = 0.0121 at an R-squared of 0.9994, rock type 2 (plug B-2, four points) b = -1.5461 and rock type 3 (plug C-3, four points) b = -1.4332. Rock type 1 reaches the reported 20 % water saturation 7.52 ft above the free-water level, rock type 2 at 9.55 ft and rock type 3 at 5.70 ft, and each still holds its 5 % irreducible water at 100 ft. Their oil in place over the column is 56.66, 48.90 and 79.22 MMSTB, 184.79 MMSTB together. The lab curve's transition zone has a buoyancy gradient of 0.0694 psi/ft, an entry height of 25.98 ft, a contact at 7,974.0 ft and a zone 90.21 ft thick, and holds 44.46 MMSTB over the zone's 640 acres against a sharp contact's 57.33 MMSTB: the sharp contact overstates the zone's oil by 29.0 %. Every one of these numbers matches its source calculation on the same inputs.

## Validity

A Leverett-J function holds within one rock type, and each rock type needs its own fit: the workbook fits three core rock types separately for that reason. The J basis: the plugs' J is the laboratory one, the Leverett J at the plug's own k and phi with the laboratory fluids (50 dyne/cm, 0 deg), and the reservoir's J at the same saturation is the same number, because the reservoir capillary pressure at a given saturation is the laboratory one times the sigma-cos-theta ratio (22.5167/50 here). The curve therefore reads J from the height above the free-water level at the plug's k and phi and the reservoir's fluids (26 dyne/cm, 30 deg), the same J the fit was made on, and the plug saturations are normalised by the irreducible water before the fit, so a curve flattens at Swi rather than at zero. The log's fit is one rock type's transition zone, and its samples are the family's synthetic interval, not field data. The power law Sw = a J^b has no entry pressure and no irreducible water: it never reaches 100 % at the free-water level and it falls without limit with height. Use it between the lowest and the highest J the samples span. The log's water saturation is Archie's, which reads too wet in shaly beds. The core plugs are Ahmed's published plug A with two synthetic plugs of the same rock type; the further plugs are points on the power law fitted to plug A, with a few percent of scatter, so the three core fits agree closely. The oil in place assumes the column's area and porosity and one saturation-height function throughout the column: a layered reservoir needs one profile per layer. The workbook does not fit a Skelt-Harrison function, a saturation-height function fitted directly to log and core data. Field units.

## References

- Leverett, M.C. (1941). Capillary Behavior in Porous Solids. *Transactions of the AIME* 142(1), 152-169.
- Archie, G.E. (1942). The Electrical Resistivity Log as an Aid in Determining Some Reservoir Characteristics. *Trans. AIME* 146, 54-62.
- Brooks, R.H. and Corey, A.T. (1964). Hydraulic Properties of Porous Media. Hydrology Papers 3, Colorado State University.
- Ahmed, T. *Reservoir Engineering Handbook*. Gulf Professional Publishing, ch. 4, Example 4-7.

## Inputs

| Input | Unit | Default | Name |
|---|---|---|---|
| Tortuosity factor a | — | 1 | `SHM_a` |
| Cementation exponent m | — | 2 | `SHM_m` |
| Saturation exponent n | — | 2 | `SHM_n` |
| Formation-water resistivity | ohm m | 0.05 | `SHM_Rw` |
| Clean-sand gamma ray | API | 30 | `SHM_GRcl` |
| Shale gamma ray | API | 115 | `SHM_GRsh` |
| Matrix density (sandstone) | g/cm3 | 2.65 | `SHM_RhoMa` |
| Fluid density (fresh mud filtrate) | g/cm3 | 1.0 | `SHM_RhoF` |
| Shale-volume cutoff for reservoir | fraction | 0.4 | `SHM_VshCut` |
| Porosity cutoff for reservoir | fraction | 0.1 | `SHM_PhiCut` |
| Water saturation whose height above the FWL is reported | fraction | 0.2 | `SHM_SwH` |
| Free-water level (the base of the clean oil sand) | ft | 5050 | `SHM_FWL` |
| Formation water density | lb/ft3 | 65.5 | `SHM_RhoW` |
| Oil density at reservoir conditions | lb/ft3 | 50 | `SHM_RhoO` |
| Oil-water interfacial tension at reservoir conditions | dyne/cm | 26 | `SHM_Ift` |
| Oil-water contact angle at reservoir conditions | deg | 30 | `SHM_Theta` |
| Core transform log10 k = A + B phi, A | — | -2.04 | `SHM_PermA` |
| Core transform, B | — | 19.67 | `SHM_PermB` |
| Permeability of plug A, kA | mD | 80 | `SHR_KA` |
| Porosity of plug A | fraction | 0.16 | `SHR_PhiA` |
| Interfacial tension of the lab fluids | dyne/cm | 50 | `SHR_IftA` |
| Contact angle of the lab fluids | deg | 0 | `SHR_ThetaA` |
| Permeability of rock B, kB | mD | 120 | `SHR_KB` |
| Porosity of rock B | fraction | 0.19 | `SHR_PhiB` |
| Interfacial tension at rock B | dyne/cm | 50 | `SHR_IftB` |
| Contact angle at rock B | deg | 0 | `SHR_ThetaB` |
| Irreducible water saturation of the rock type | fraction | 0.05 | `SHR_Swi` |
| Water saturation to read rock B at | fraction | 0.4 | `SHR_Sw` |
| Area of the column | acres | 640 | `SHV_Area` |
| Oil formation volume factor | bbl/STB | 1.25 | `SHV_Bo` |
| Barrels in one acre foot (constant) | bbl/acre ft | 7758 | `SHV_AcFt` |
| Lab curve: irreducible water saturation | fraction | 0.2 | `SHV_Swi` |
| Lab curve: porosity | fraction | 0.2 | `SHV_Phi` |
| Lab curve: entry pressure, Pd | psi | 5 | `SHV_Pd` |
| Lab curve: pore-size distribution index | — | 2 | `SHV_Lambda` |
| Lab curve: surface tension of the lab fluids | dyne/cm | 72 | `SHV_IftLab` |
| Lab curve: contact angle of the lab fluids | deg | 0 | `SHV_ThetaLab` |
| Lab curve: oil-water interfacial tension | dyne/cm | 30 | `SHV_IftRes` |
| Lab curve: oil-water contact angle | deg | 30 | `SHV_ThetaRes` |
| Lab curve: water density | lb/ft3 | 65.2 | `SHV_RhoW` |
| Lab curve: oil density | lb/ft3 | 55.2 | `SHV_RhoO` |

## Sheets

- `Guide` — the workflow and which fit answers which question.
- `Log Fit` — the log's own fit on the clean oil sand's transition zone, the family's synthetic interval from 5,014 to 5,048 ft above a free-water level at 5,050 ft: eighteen samples of one rock type, each with its water saturation by Archie, its height, its reservoir capillary pressure and its Leverett J; the power-law fit and its scatter; the Sw against height chart; and the clean oil sand's Archie saturation with the water-sand calibration.
- `Rock Types` — Ahmed's thirteen core plugs (plug A, plug B-2 and plug C-3 rock types), the reference J curve and the scaling of plug A to rock B, and one Leverett-J fit per rock type on its own plugs.
- `Sw by Height` — the log function at its three rocks and each core rock type's function against height above the free-water level, each rock type's height to the reported Sw, and the chart.
- `Volumes` — each core rock type's oil in place over the column, band by band, and the lab curve's Brooks-Corey transition zone with its own oil in place against a sharp contact and its saturation-height profile.
- `Summary` — the log fit, the three core rock types' fits, the oil in place and every check under one verdict.
- `Test Cases` — the worked example and other cases, with expected and computed results.

## Functions used

`PO.PP.Vsh.GammaRayIndex`, `PO.PP.Porosity.FromDensity`, `PO.PP.Sw.Archie`, `PO.PP.F.Archie`, `PO.SCAL.Leverett.J`, `PO.SCAL.Leverett.Pc`, `PO.SCAL.PcToHeight`, `PO.SCAL.BrooksCorey.Pc`, `LINEST`.
