---
id: po.wb.gl.field-optimisation
title: Gas-Lift Field Optimisation
summary: "How to split a limited lift-gas supply across four wells for the most oil, and where the first well then injects."
category: Production
requires:
  - po-addin
tags:
  - gas-lift
  - production-optimisation
---

## Description

How should a limited lift-gas supply be split between wells to make the most oil? You enter the shared tubing and fluid data, each of four wells' depth, reservoir pressure, bubble point, productivity index, gas-liquid ratio and water cut, and the gas available. You read off each well's lift gas and oil by equal marginal slope, the field oil against no lift gas and an even split, and the first well's injection depth and valve differential. Field units, pressures absolute; the PO add-in is needed.

**How to use it:** The four wells are synthetic; replace every example with measured, test-matched field data. Enter the shared tubing and fluid inputs, the four reservoir and depth cases, the gas available, the grid step, the crossing tolerance, the casing gradient and the differential on the Allocation sheet. The Injection sheet takes W1's allocated gas and the same conditions; the minimum acceptable injection-depth fraction is an editable assumption there. Review the flow, curve-shape, gas and injection checks on the Summary.

**Method:** For each well, nine gas-rate points are computed with a composite Vogel IPR and Hagedorn-Brown tubing, with two starting pressures and three bounded secant passes. Piecewise-linear marginal oil slopes allocate gas by equal slope. Tied marginal steps are taken deterministically in well order, with successive tied steps on a well taken in curve order. The result includes zero-gas and even-split comparisons. W1's allocated oil and water cut give its liquid rate; its allocated gas gives the total GLR for a two-pass static gas column and tubing profile that locate its injection point.

**Example:** The synthetic 1,600 Mscf/d case is approximately 400, 750, 150 and 300 Mscf/d across W1-W4, producing approximately 2,391 STB/d versus 2,347 STB/d for an even split. These rounded figures are indicative; use the recalculated unrounded workbook values.

## Validity

The example is not a field design. Wells share tubing and fluid assumptions. Equal slope is optimal only for the sampled piecewise-linear curves when marginal returns do not increase; warnings identify departures. Allocation assumes injection at the bottom and a constant casing gas gradient. The separate W1 profile can find a shallower injection point and assumes all gas is present throughout the tubing; neither calculation is a segmented gas-lift traverse. Kickoff pressure of 1,200 psia is an assumed operating casinghead pressure for the linked case, not the independent GL-1 example's 1,000 psia. A zero-flow W1 has no pressure profile. At 100% water cut (or higher) W1 liquid rate cannot be inferred from oil; the zero shown in the liquid-rate cell is only a calculation placeholder, and the W1 checks fail rather than claim no liquid flow. Validate correlations and pressure limits against field surveys and vendor specifications.

## References

- Kanu, E.P., Mach, J. and Brown, K.E. (1981). Economic Approach to Oil Production and Gas Allocation in Continuous Gas Lift. *JPT* 33(10), 1887-1892.
- Brown, K.E. (1980). *The Technology of Artificial Lift Methods*, Vol. 2a. PennWell.
- Takacs, G. (2005). *Gas Lift Manual*. PennWell.
- American Petroleum Institute. *API RP 11V6, Recommended Practice for Design of Continuous Flow Gas Lift Installations Using Injection Pressure Operated Valves*.
- Vogel, J.V. (1968). Inflow Performance Relationships for Solution-Gas Drive Wells. *JPT* 20(1), 83-92.
- Hagedorn, A.R. and Brown, K.E. (1965). Experimental Study of Pressure Gradients Occurring During Continuous Two-Phase Flow in Small-Diameter Vertical Conduits. *JPT* 17(4), 475-484.

## Inputs

| Input | Unit | Default | Name |
|---|---|---|---|
| Flowing wellhead pressure | psia | 120 | `FOA_Pwh` |
| Surface temperature | °F | 80 | `FOA_Ts` |
| Geothermal gradient (200 °F at GL-1's 8,000 ft) | °F/100 ft | 1.5 | `FOA_Tgrad` |
| Gas specific gravity, formation and lift gas | — | 0.65 | `FOA_SGg` |
| Stock-tank oil specific gravity | — | 0.85 | `FOA_SGo` |
| Brine specific gravity | — | 1.05 | `FOA_SGw` |
| Liquid viscosity in the tubing | cP | 2 | `FOA_UL` |
| Gas-liquid surface tension | dyne/cm | 30 | `FOA_IFT` |
| Tubing inner diameter | in | 2.441 | `FOA_ID` |
| Tubing relative roughness, ε/D | — | 0.0006 | `FOA_Rough` |
| Depth of the injection point and perforations, wells 1 to 4 | ft | 8,000, 7,500, 8,500, 7,000 | `FOA_D1` … `FOA_D4` |
| Average reservoir pressure, wells 1 to 4 | psia | 2,250, 1,800, 2,400, 1,700 | `FOA_Pr1` … `FOA_Pr4` |
| Bubble-point pressure, wells 1 to 4 | psia | 1,500, 1,500, 1,800, 1,200 | `FOA_Pb1` … `FOA_Pb4` |
| Productivity index above the bubble point, wells 1 to 4 | STB/d/psi | 1.0, 2.5, 0.6, 1.5 | `FOA_J1` … `FOA_J4` |
| Formation gas-liquid ratio, wells 1 to 4 | scf/STB | 300, 200, 400, 150 | `FOA_GLR1` … `FOA_GLR4` |
| Water cut, wells 1 to 4 | % | 25, 30, 10, 80 | `FOA_WC1` … `FOA_WC4` |
| Lift gas available to the four wells | Mscf/d | 1,600 | `FOA_Gav` |
| Lift-gas step of the performance curves (nine rates from 0) | Mscf/d | 150 | `FOA_Step` |
| Largest pressure miss accepted at a crossing | psi | 1 | `FOA_Tol` |
| Lift-gas pressure at the casinghead | psia | 1,200 | `FOA_Pinj` |
| Casing gas gradient | psi/ft | 0.0253 | `FOA_Gg` |
| Least casing-over-tubing differential at the injection point | psi | 100 | `FOA_dPmin` |
| Least injection depth, share of packer depth (Injection) | % | 75 | `FOI_PoiMin` |

## Sheets

- `Guide` — four synthetic wells sharing a limited lift-gas supply, the data to use and the assumptions of the allocation and the W1 profile.
- `Allocation` — the shared tubing and fluids and the four wells; each well's performance curve, its IPR against the tubing curve at nine lift-gas rates; the equal-slope field allocation and each well's share of the gas against an even split; and the field curve with λ swept through every step's slope, charted.
- `Injection` — W1 at its allocated gas: the casing gas column and the flowing tubing pressure meeting the minimum valve differential at the point of injection, and the pressure profile.
- `Summary` — gas used, field oil, oil without lift gas, even-split oil and the gain over it, the marginal oil per gas, each well's gas and oil, W1's injection depth and valve differential, and every check under one verdict.
- `Test Cases` — the worked example and other cases, with expected and computed results.

Two charts: the four wells' gas-lift performance curves, and field oil against field lift gas.

## Functions used

`PO.IPR.VW.PSS.Rate.ByVogel`, `PO.VFP.HagedornBrown.Pin`, `PO.GL.Inj.Qgi`, `PO.GL.Inj.Grad`, `PO.GL.Inj.Pd`, `PO.GL.Inj.Eff`, `PO.PVT.Z.ByDAK`, `PO.PVT.Ppc.ByStanding` and `PO.PVT.Tpc.ByStanding`.
