---
cid: po.bp.sf.separator.sizing
hub: sf
tags: [separator, Souders-Brown, retention-time, vessel-sizing, slenderness, three-phase, surface-facilities]
facets: { discipline: production, phase: multiphase }
title: Separator Sizing by Souders-Brown and Retention Time
summary: "Sizes a two- or three-phase separator from Souders-Brown gas capacity and liquid retention times, sweeping standard vessel diameters."
slug: po.sf.separator.sizing
type: worksheet
---

# Separator Sizing by Souders-Brown and Retention Time

## Description

What vessel separates the stream, and how long is it? You enter the gas, oil and water rates, the separator's pressure and temperature, the gas and liquid gravities, the orientation, two or three phases, the retention times, the K factor and the slenderness limits. You read off the smallest diameter that carries the gas, the liquid volume held, and the recommended standard vessel's diameter, seam-to-seam length and slenderness; an existing vessel is rated against the same duty.

**Parameters:**
- **Stream**: the gas, oil and water rates `SEP_Qg`, `SEP_Qo`, `SEP_Qw`, and the separator's pressure `SEP_P` and temperature `SEP_T`
- **Gas and liquid**: the gas gravity `SEP_SG`, its CO2 `SEP_CO2` and H2S `SEP_H2S`, and the liquid gravity `SEP_SGL`
- **Vessel**: the orientation `SEP_Orient` (1 horizontal, 2 vertical), the phases `SEP_Phases` (2 or 3), the oil and water retention times `SEP_TrO`, `SEP_TrW`, the K factor `SEP_K` and the slenderness limits `SEP_SRmin`, `SEP_SRmax`
- **Existing vessel**: its internal diameter `SEP_Dv` and seam-to-seam length `SEP_Lv`

**How to use it:** Take the operating pressure and temperature from the separator's own gauges, the rates from the test or allocation meters, the K factor from the mist extractor's rating (derated at high pressure), and the retention times from bottle tests of the oil and water. Swap the standard diameters in the table for the fabricator's. The gas sets a smallest diameter: below it the gas moves faster than the Souders-Brown velocity and carries liquid over. The liquid sets a volume: the oil and water held for their retention times. A table sweeps standard vessel diameters from 24 to 120 in, with each one's liquid length, its seam-to-seam length and its slenderness, and the chart draws the seam-to-seam length against the diameter between the slenderness limits. The recommended vessel is the smallest diameter that carries the gas and stays within the largest slenderness.

**Method:**

- **Gas.** Z is DAK's at Standing's pseudo-criticals, corrected for CO2 and H2S by Wichert and Aziz. The allowable velocity is Vt = K·√((ρl − ρg)/ρg). The gas flow at the separator, over Vt, gives the area the gas needs: the whole section of a vertical vessel, or the upper half of a horizontal one taken half full of liquid. That area gives the gas-capacity diameter.
- **Liquid.** The liquid volume is (Qo·tr,o + Qw·tr,w)/1,440 bbl for three phases, or (Qo + Qw)·tr,o/1,440 for two. The liquid length in a vessel of diameter D is that volume over the liquid's share of the section: the effective length of a horizontal vessel, half full, or the liquid height of a vertical one.
- **Seam-to-seam length.** A horizontal vessel's seam-to-seam length is the larger of 4/3 of its effective length and the effective length plus D/12 ft, Arnold and Stewart's allowances for the inlet and gas sections. A vertical one adds the height above the liquid: 76 in up to 36 in diameter, and D + 40 in beyond.
- **Slenderness.** The slenderness is 12·Lss/D. The recommended vessel is the first standard diameter at or above the gas-capacity diameter whose slenderness is at most the largest slenderness. The gas sets it when that is the first standard size above the gas-capacity diameter; otherwise the liquid does, at the slenderness limit.
- **Existing vessel.** Its liquid length follows from its seam-to-seam length by the same allowances. The oil's retention time in it is the design time scaled by the liquid length it has over the length the duty needs.
- **Checks.**
  - Slenderness: the recommended vessel's slenderness lies between the limits.
  - Retention: the times are within API 12J's guide, 1 to 3 min for two phases and 3 to 30 for three.
  - Existing vessel: it carries the gas and holds the oil for the design time.

**Example:** The default case is the stream of the flow-assurance family's reference flowline as it reaches the facility: 20 MMscf/d of the 0.7 gravity gas with 3 % CO2 and 500 ppm H2S, 1,000 STB/d of the reference oil and 500 bbl/d of water, blended to a 0.89 gravity. The Multiphase Flowline by Beggs and Brill sheet delivers it at 741 psia; a choke at the riser top takes it down to the separator's 250 psia, and the inlet heater warms it to 80 °F. The vessel is a horizontal three-phase separator holding the oil and the water 10 minutes each, with a K factor of 0.5 ft/s for a 10 ft horizontal vessel with a mist pad, the top of the API 12J range. The existing vessel to rate is 48 in by 15 ft.

Z at 250 psia and 80 °F is 0.9536, and the gas weighs 0.918 lb/ft³ against the liquid's 55.56. With K = 0.5 the gas may move at 3.858 ft/s. The 13.48 ft³/s of gas in half the section needs a 35.79 in vessel, so the smallest standard diameter that carries it is 36 in. The liquid held for 10 minutes is 10.42 bbl. In a 36 in vessel that is 16.55 ft of liquid and 22.06 ft seam to seam, a slenderness of 7.35, too slender. At 42 in it is 12.16 ft of liquid and 16.21 ft seam to seam, a slenderness of 4.63: the recommended vessel, set by the liquid at the slenderness limit. The gas moves at 2.80 ft/s in it, 73 % of Vt. The existing 48 in by 15 ft vessel has 11 ft of liquid length against the 9.31 ft the duty needs at 48 in, so it holds the oil 11.8 minutes: it passes. Cut to 8 ft it holds 4.3 minutes and fails. A vertical vessel with K = 0.25 and a slenderness limit of 4 also comes out at 42 in, 12.91 ft tall. A two-phase vessel holding the liquid 3 minutes needs only 3.13 bbl, so the gas sets it: 36 in by 7.96 ft, a slenderness of 2.65, short.

## Validity

Souders-Brown sizing for liquid droplets in the gas, with K carrying the design: the internals, the droplet size they pass and the pressure. API 12J's K ranges, as they are commonly reproduced, are 0.12 to 0.24 ft/s for a vertical vessel 5 ft tall, 0.18 to 0.35 ft/s for one 10 ft tall, and 0.40 to 0.50 ft/s for a horizontal vessel 10 ft long, scaled by (L/10)^0.56 for other lengths. GPSA derates a mesh pad at high pressure. A horizontal vessel is taken half full: another liquid level changes both the gas and the liquid area, and the diameter scales as one over the square root of the gas's share. The retention times are the design choice: foaming, heavy or cold oil, and emulsions, need more than the guide. The three-phase sizing doesn't check the oil pad's thickness for water droplets to fall through it, or the water's residence for oil droplets to rise. The density constant of the Souders-Brown sizing (28.9625/10.7316) is 0.08 % below the one in the PVT gas density the sheet shows ρg by, so the shown density reads a hair high.

Named alternatives: Arnold and Stewart's droplet-settling sizing from a drag coefficient and a droplet size (d·Leff for the gas in a horizontal vessel); a Stokes settling length for the oil pad, which this sheet doesn't compute; a vendor's sizing from its internals' rated capacity; and an equilibrium flash at separator conditions for the separator's gas and liquid splits.

## References

- Souders, M. and Brown, G.G. (1934). "Design of Fractionating Columns: I. Entrainment and Capacity." *Industrial & Engineering Chemistry* 26(1), 98–103.
- API Specification 12J (2008). *Specification for Oil and Gas Separators*, 8th ed., Annex C (K factors and retention times; not to hand, the ranges as commonly reproduced).
- Arnold, K. and Stewart, M. (2008). *Surface Production Operations*, vol. 1, 3rd ed., Gulf, ch. 4 and 5 (the gas and liquid capacity, seam-to-seam allowances and slenderness; not to hand, their worked examples not reproduced).
- GPSA (2012). *Engineering Data Book*, 13th ed., section 7.
- Wichert, E. and Aziz, K. (1972). "Calculate Z's for Sour Gases." *Hydrocarbon Processing* 51(5), 119–122.

## Functions used

`PO.PVT.Ppc.ByStanding.Sour`, `PO.PVT.Tpc.ByStanding.Sour`, `PO.PVT.Z.ByDAK`, `PO.PVT.Rho.Gas.ByDefinition`, `PO.PVT.Rho.Wat.Stn`, `PO.PVT.Bg.ByDefinition`, `PO.SF.Sep.SoudersBrown`, `PO.SF.Sep.LiquidRetention`

## Spreadsheet: SfSeparatorSizing

|    | A                                                                                                                                                                                                                                 | B                                                                                                                                                                     | C                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        | D                                                                                                             | E                 | F                                  | G                       | H                       | I                                                                                                    | J | K                | L                             |
|----|-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|-----------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|---------------------------------------------------------------------------------------------------------------|-------------------|------------------------------------|-------------------------|-------------------------|------------------------------------------------------------------------------------------------------|---|------------------|-------------------------------|
| 1  | Separator Sizing by Souders-Brown and Retention Time                                                                                                                                                                              |                                                                                                                                                                       | Petroleum Office                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                         |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 2  | Blue cells on yellow are inputs. Type the stream, the operating pressure and temperature, the vessel's orientation, retention times and K factor; the gas-capacity diameter, the liquid length and the recommended vessel follow. |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 3  | Stream at the Facility (the Reference Flowline's Arrival)                                                                                                                                                                         |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 4  | Gas rate                                                                                                                                                                                                                          | 20                                                                                                                                                                    | MMscf/d                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 5  | Oil rate                                                                                                                                                                                                                          | 1000                                                                                                                                                                  | STB/d                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 6  | Water rate                                                                                                                                                                                                                        | 500                                                                                                                                                                   | STB/d                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 7  | Separator operating pressure, absolute                                                                                                                                                                                            | 250                                                                                                                                                                   | psia                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 8  | Separator operating temperature (after the inlet heater)                                                                                                                                                                          | 80                                                                                                                                                                    | °F                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 9  | Gas and Liquid                                                                                                                                                                                                                    |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 10 | Gas specific gravity (air = 1)                                                                                                                                                                                                    | 0.7                                                                                                                                                                   | air = 1                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 11 | CO2 mole fraction                                                                                                                                                                                                                 | 0.03                                                                                                                                                                  | %                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 12 | H2S in the gas                                                                                                                                                                                                                    | 500                                                                                                                                                                   | ppm                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 13 | Liquid specific gravity (oil and water blended)                                                                                                                                                                                   | 0.89                                                                                                                                                                  | water = 1                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 14 | Vessel and Design Basis                                                                                                                                                                                                           |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 15 | Orientation (1 horizontal, 2 vertical)                                                                                                                                                                                            | 1                                                                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 16 | Phases separated (2 gas-liquid, 3 gas-oil-water)                                                                                                                                                                                  | 3                                                                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 17 | Retention time of the oil (of all the liquid if two-phase)                                                                                                                                                                        | 10                                                                                                                                                                    | min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 18 | Retention time of the water (three-phase)                                                                                                                                                                                         | 10                                                                                                                                                                    | min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 19 | Souders-Brown K factor for the vessel and mist extractor                                                                                                                                                                          | 0.5                                                                                                                                                                   | ft/s                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 20 | Smallest slenderness, seam-to-seam length over diameter                                                                                                                                                                           | 3                                                                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 21 | Largest slenderness (about 5 horizontal, 4 vertical)                                                                                                                                                                              | 5                                                                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 22 | Existing Vessel to Rate                                                                                                                                                                                                           |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 23 | Existing vessel's internal diameter                                                                                                                                                                                               | 48                                                                                                                                                                    | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 24 | Existing vessel's seam-to-seam length                                                                                                                                                                                             | 15                                                                                                                                                                    | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 26 | Gas Capacity (Souders-Brown)                                                                                                                                                                                                      |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 27 | Temperature, absolute                                                                                                                                                                                                             | =SEP_T+SEP_R0                                                                                                                                                         | °R                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 28 | Pseudo-critical pressure, p′pc (Standing, Wichert-Aziz)                                                                                                                                                                           | =PO.PVT.Ppc.ByStanding.Sour(SEP_SG,SEP_H2S/SEP_Ppm,SEP_CO2)                                                                                                           | psi                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 29 | Pseudo-critical temperature, T′pc                                                                                                                                                                                                 | =PO.PVT.Tpc.ByStanding.Sour(SEP_SG,SEP_H2S/SEP_Ppm,SEP_CO2)                                                                                                           | °R                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 30 | Z-factor at the separator (DAK)                                                                                                                                                                                                   | =PO.PVT.Z.ByDAK(SEP_P/SEP_Ppc,SEP_TR/SEP_Tpc)                                                                                                                         | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 31 | Gas density at the separator                                                                                                                                                                                                      | =PO.PVT.Rho.Gas.ByDefinition(SEP_P,SEP_TR,SEP_SG,SEP_Z)*PO.PVT.Rho.Wat.Stn()                                                                                          | lb/ft³                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                   |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 32 | Liquid density, SGL × water's                                                                                                                                                                                                     | =SEP_SGL*PO.PVT.Rho.Wat.Stn()                                                                                                                                         | lb/ft³                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                   |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 33 | Vessel orientation                                                                                                                                                                                                                | =""&CHOOSE(SEP_Orient,"Horizontal","Vertical")                                                                                                                        |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 34 | Allowable gas velocity, Vt = K·√((ρl − ρg)/ρg)                                                                                                                                                                                    | =PO.SF.Sep.SoudersBrown(SEP_Vessel,SEP_Qg,SEP_P,SEP_T,SEP_Z,SEP_SG,SEP_RhoL,SEP_K,"Velocity")                                                                         | ft/s                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 35 | Gas flow at the separator                                                                                                                                                                                                         | =SEP_Qg*SEP_Scf*PO.PVT.Bg.ByDefinition(SEP_P,SEP_TR,SEP_Z)/SEP_Sec                                                                                                    | ft³/s                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 36 | Smallest diameter for the gas                                                                                                                                                                                                     | =PO.SF.Sep.SoudersBrown(SEP_Vessel,SEP_Qg,SEP_P,SEP_T,SEP_Z,SEP_SG,SEP_RhoL,SEP_K,"Diameter")                                                                         | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 37 | Liquid Capacity (Retention Time)                                                                                                                                                                                                  |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 38 | Liquid held for the retention times                                                                                                                                                                                               | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,SEP_Dgas,"Volume")                                                                     | bbl                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 39 | Liquid rate, oil and water                                                                                                                                                                                                        | =SEP_Qo+SEP_Qw                                                                                                                                                        | STB/d                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 40 | Recommended Vessel                                                                                                                                                                                                                |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 41 | Smallest standard diameter that carries the gas                                                                                                                                                                                   | =INDEX($A$62:$A$74,MATCH(1,$B$62:$B$74,0))                                                                                                                            | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 42 | Recommended diameter, the smallest within the slenderness                                                                                                                                                                         | =INDEX($A$62:$A$74,MATCH(1,$F$62:$F$74,0))                                                                                                                            | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 43 | Liquid length in it, effective (horizontal) or height (vertical)                                                                                                                                                                  | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,SEP_Drec,"Length")                                                                     | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 44 | Seam-to-seam length                                                                                                                                                                                                               | =INDEX($D$62:$D$74,MATCH(1,$F$62:$F$74,0))                                                                                                                            | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 45 | Slenderness, 12·Lss/D                                                                                                                                                                                                             | =SEP_Lss*SEP_InFt/SEP_Drec                                                                                                                                            | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 46 | What sets the diameter                                                                                                                                                                                                            | =""&IF(SEP_Drec=SEP_Dstd,"Gas capacity","Liquid retention, at the slenderness limit")                                                                                 |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 47 | Gas velocity in it                                                                                                                                                                                                                | =SEP_Qa/(PI()*(SEP_Drec/SEP_InFt/2)^2*IF(SEP_Orient=1,SEP_Half,1))                                                                                                    | ft/s                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 48 | Gas velocity over the allowable, Vg/Vt                                                                                                                                                                                            | =SEP_Vg/SEP_Vt                                                                                                                                                        | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 49 | Existing Vessel                                                                                                                                                                                                                   |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 50 | Liquid length it has, from its seam-to-seam length                                                                                                                                                                                | =IF(SEP_Orient=1,MIN(SEP_Lv/SEP_Shell,SEP_Lv-SEP_Dv/SEP_InFt),SEP_Lv-IF(SEP_Dv<=SEP_VertD,SEP_VertA,SEP_Dv+SEP_VertB)/SEP_InFt)                                       | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 51 | Liquid length the duty needs at its diameter                                                                                                                                                                                      | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,SEP_Dv,"Length")                                                                       | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 52 | Oil retention time it gives (all the liquid's if two-phase)                                                                                                                                                                       | =SEP_TrO*SEP_LvLiq/SEP_LvNeed                                                                                                                                         | min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 53 | Slenderness check                                                                                                                                                                                                                 | =IF(ISNA(SEP_Drec),"FAIL",IF(SEP_SR<SEP_SRmin,"WARN","PASS"))                                                                                                         | =IF(ISNA(SEP_Drec),"no standard diameter up to "&FIXED(MAX($A$62:$A$74),0)&" in carries the gas within a slenderness of "&FIXED(SEP_SRmax,2)&"; raise K or split the stream",IF(SEP_SR<SEP_SRmin,""&FIXED(SEP_Drec,0)&" in by "&FIXED(SEP_Lss,2)&" ft is "&FIXED(SEP_SR,2)&" diameters long, under "&FIXED(SEP_SRmin,2)&": the gas sets a short, wide vessel; check the liquid level and inlet spacing",""&FIXED(SEP_Drec,0)&" in by "&FIXED(SEP_Lss,2)&" ft seam to seam, a slenderness of "&FIXED(SEP_SR,2)&", within "&FIXED(SEP_SRmin,2)&" to "&FIXED(SEP_SRmax,2)))                                 |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 54 | Retention time check                                                                                                                                                                                                              | =IF(SEP_Phases=2,IF(AND(SEP_TrO>=SEP_Tr2Lo,SEP_TrO<=SEP_Tr2Hi),"PASS","WARN"),IF(AND(MIN(SEP_TrO,SEP_TrW)>=SEP_Tr3Lo,MAX(SEP_TrO,SEP_TrW)<=SEP_Tr3Hi),"PASS","WARN")) | =IF(SEP_Phases=2,IF(AND(SEP_TrO>=SEP_Tr2Lo,SEP_TrO<=SEP_Tr2Hi),""&FIXED(SEP_TrO,0)&" min is within API 12J's 1 to 3 min for two-phase",""&FIXED(SEP_TrO,0)&" min is outside API 12J's 1 to 3 min for two-phase: foaming or heavy oil needs more, check it"),IF(AND(MIN(SEP_TrO,SEP_TrW)>=SEP_Tr3Lo,MAX(SEP_TrO,SEP_TrW)<=SEP_Tr3Hi),""&FIXED(SEP_TrO,0)&" min oil and "&FIXED(SEP_TrW,0)&" min water are within API 12J's 3 to 30 min for three-phase",""&FIXED(SEP_TrO,0)&" min oil and "&FIXED(SEP_TrW,0)&" min water are outside API 12J's 3 to 30 min for three-phase: set them from bottle tests")) |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 55 | Existing vessel check                                                                                                                                                                                                             | =IF(SEP_Dv<SEP_Dgas,"FAIL",IF(SEP_TrAvail<SEP_TrO,"FAIL","PASS"))                                                                                                     | =IF(SEP_Dv<SEP_Dgas,"the existing "&FIXED(SEP_Dv,0)&" in vessel is under the "&FIXED(SEP_Dgas,2)&" in the gas needs: liquid will carry over",IF(SEP_TrAvail<SEP_TrO,"the existing "&FIXED(SEP_Dv,0)&" in by "&FIXED(SEP_Lv,2)&" ft vessel holds the oil "&FIXED(SEP_TrAvail,2)&" min, under the "&FIXED(SEP_TrO,0)&" min wanted","the existing "&FIXED(SEP_Dv,0)&" in by "&FIXED(SEP_Lv,2)&" ft vessel carries the gas and holds the oil "&FIXED(SEP_TrAvail,2)&" min"))                                                                                                                                 |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 59 | Standard Vessel Diameters                                                                                                                                                                                                         |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 60 | How to use it: the separator's own operating pressure and temperature, the metered rates, the K factor from the mist extractor's rating, retention times from bottle tests, and the vendor's diameters.                           |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 61 | ID (in)                                                                                                                                                                                                                           | Carries gas (1 = yes)                                                                                                                                                 | Liquid length (ft)                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       | Seam-to-seam (ft)                                                                                             | Slenderness (—)   | Fits (1 = yes)                     | At minimum (ft)         | At maximum (ft)         | Verdict                                                                                              |   | Gas minimum (in) | Length (ft)                   |
| 62 | 24                                                                                                                                                                                                                                | =IF(A62>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A62,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C62,C62+A62/SEP_InFt),C62+IF(A62<=SEP_VertD,SEP_VertA,A62+SEP_VertB)/SEP_InFt) | =D62*SEP_InFt/A62 | =IF(AND(B62=1,E62<=SEP_SRmax),1,0) | =SEP_SRmin*A62/SEP_InFt | =SEP_SRmax*A62/SEP_InFt | =IF(B62=0,"FAIL: gas carries over",IF(E62>SEP_SRmax,"too slender",IF(E62<SEP_SRmin,"short","fits"))) |   | =SEP_Dgas        | 0                             |
| 63 | 30                                                                                                                                                                                                                                | =IF(A63>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A63,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C63,C63+A63/SEP_InFt),C63+IF(A63<=SEP_VertD,SEP_VertA,A63+SEP_VertB)/SEP_InFt) | =D63*SEP_InFt/A63 | =IF(AND(B63=1,E63<=SEP_SRmax),1,0) | =SEP_SRmin*A63/SEP_InFt | =SEP_SRmax*A63/SEP_InFt | =IF(B63=0,"FAIL: gas carries over",IF(E63>SEP_SRmax,"too slender",IF(E63<SEP_SRmin,"short","fits"))) |   | =SEP_Dgas        | =MAX($D$62:$D$74,$H$62:$H$74) |
| 64 | 36                                                                                                                                                                                                                                | =IF(A64>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A64,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C64,C64+A64/SEP_InFt),C64+IF(A64<=SEP_VertD,SEP_VertA,A64+SEP_VertB)/SEP_InFt) | =D64*SEP_InFt/A64 | =IF(AND(B64=1,E64<=SEP_SRmax),1,0) | =SEP_SRmin*A64/SEP_InFt | =SEP_SRmax*A64/SEP_InFt | =IF(B64=0,"FAIL: gas carries over",IF(E64>SEP_SRmax,"too slender",IF(E64<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 65 | 42                                                                                                                                                                                                                                | =IF(A65>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A65,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C65,C65+A65/SEP_InFt),C65+IF(A65<=SEP_VertD,SEP_VertA,A65+SEP_VertB)/SEP_InFt) | =D65*SEP_InFt/A65 | =IF(AND(B65=1,E65<=SEP_SRmax),1,0) | =SEP_SRmin*A65/SEP_InFt | =SEP_SRmax*A65/SEP_InFt | =IF(B65=0,"FAIL: gas carries over",IF(E65>SEP_SRmax,"too slender",IF(E65<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 66 | 48                                                                                                                                                                                                                                | =IF(A66>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A66,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C66,C66+A66/SEP_InFt),C66+IF(A66<=SEP_VertD,SEP_VertA,A66+SEP_VertB)/SEP_InFt) | =D66*SEP_InFt/A66 | =IF(AND(B66=1,E66<=SEP_SRmax),1,0) | =SEP_SRmin*A66/SEP_InFt | =SEP_SRmax*A66/SEP_InFt | =IF(B66=0,"FAIL: gas carries over",IF(E66>SEP_SRmax,"too slender",IF(E66<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 67 | 54                                                                                                                                                                                                                                | =IF(A67>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A67,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C67,C67+A67/SEP_InFt),C67+IF(A67<=SEP_VertD,SEP_VertA,A67+SEP_VertB)/SEP_InFt) | =D67*SEP_InFt/A67 | =IF(AND(B67=1,E67<=SEP_SRmax),1,0) | =SEP_SRmin*A67/SEP_InFt | =SEP_SRmax*A67/SEP_InFt | =IF(B67=0,"FAIL: gas carries over",IF(E67>SEP_SRmax,"too slender",IF(E67<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 68 | 60                                                                                                                                                                                                                                | =IF(A68>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A68,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C68,C68+A68/SEP_InFt),C68+IF(A68<=SEP_VertD,SEP_VertA,A68+SEP_VertB)/SEP_InFt) | =D68*SEP_InFt/A68 | =IF(AND(B68=1,E68<=SEP_SRmax),1,0) | =SEP_SRmin*A68/SEP_InFt | =SEP_SRmax*A68/SEP_InFt | =IF(B68=0,"FAIL: gas carries over",IF(E68>SEP_SRmax,"too slender",IF(E68<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 69 | 66                                                                                                                                                                                                                                | =IF(A69>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A69,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C69,C69+A69/SEP_InFt),C69+IF(A69<=SEP_VertD,SEP_VertA,A69+SEP_VertB)/SEP_InFt) | =D69*SEP_InFt/A69 | =IF(AND(B69=1,E69<=SEP_SRmax),1,0) | =SEP_SRmin*A69/SEP_InFt | =SEP_SRmax*A69/SEP_InFt | =IF(B69=0,"FAIL: gas carries over",IF(E69>SEP_SRmax,"too slender",IF(E69<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 70 | 72                                                                                                                                                                                                                                | =IF(A70>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A70,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C70,C70+A70/SEP_InFt),C70+IF(A70<=SEP_VertD,SEP_VertA,A70+SEP_VertB)/SEP_InFt) | =D70*SEP_InFt/A70 | =IF(AND(B70=1,E70<=SEP_SRmax),1,0) | =SEP_SRmin*A70/SEP_InFt | =SEP_SRmax*A70/SEP_InFt | =IF(B70=0,"FAIL: gas carries over",IF(E70>SEP_SRmax,"too slender",IF(E70<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 71 | 84                                                                                                                                                                                                                                | =IF(A71>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A71,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C71,C71+A71/SEP_InFt),C71+IF(A71<=SEP_VertD,SEP_VertA,A71+SEP_VertB)/SEP_InFt) | =D71*SEP_InFt/A71 | =IF(AND(B71=1,E71<=SEP_SRmax),1,0) | =SEP_SRmin*A71/SEP_InFt | =SEP_SRmax*A71/SEP_InFt | =IF(B71=0,"FAIL: gas carries over",IF(E71>SEP_SRmax,"too slender",IF(E71<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 72 | 96                                                                                                                                                                                                                                | =IF(A72>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A72,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C72,C72+A72/SEP_InFt),C72+IF(A72<=SEP_VertD,SEP_VertA,A72+SEP_VertB)/SEP_InFt) | =D72*SEP_InFt/A72 | =IF(AND(B72=1,E72<=SEP_SRmax),1,0) | =SEP_SRmin*A72/SEP_InFt | =SEP_SRmax*A72/SEP_InFt | =IF(B72=0,"FAIL: gas carries over",IF(E72>SEP_SRmax,"too slender",IF(E72<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 73 | 108                                                                                                                                                                                                                               | =IF(A73>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A73,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C73,C73+A73/SEP_InFt),C73+IF(A73<=SEP_VertD,SEP_VertA,A73+SEP_VertB)/SEP_InFt) | =D73*SEP_InFt/A73 | =IF(AND(B73=1,E73<=SEP_SRmax),1,0) | =SEP_SRmin*A73/SEP_InFt | =SEP_SRmax*A73/SEP_InFt | =IF(B73=0,"FAIL: gas carries over",IF(E73>SEP_SRmax,"too slender",IF(E73<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 74 | 120                                                                                                                                                                                                                               | =IF(A74>=SEP_Dgas,1,0)                                                                                                                                                | =PO.SF.Sep.LiquidRetention(SEP_Phases,SEP_Vessel,SEP_Qo,SEP_Qw,SEP_TrO,SEP_TrW,A74,"Length")                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                             | =IF(SEP_Orient=1,MAX(SEP_Shell*C74,C74+A74/SEP_InFt),C74+IF(A74<=SEP_VertD,SEP_VertA,A74+SEP_VertB)/SEP_InFt) | =D74*SEP_InFt/A74 | =IF(AND(B74=1,E74<=SEP_SRmax),1,0) | =SEP_SRmin*A74/SEP_InFt | =SEP_SRmax*A74/SEP_InFt | =IF(B74=0,"FAIL: gas carries over",IF(E74>SEP_SRmax,"too slender",IF(E74<SEP_SRmin,"short","fits"))) |   |                  |                               |
| 76 | Calculation Constants                                                                                                                                                                                                             |                                                                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 77 | Rankine at 0 °F                                                                                                                                                                                                                   | 459.67                                                                                                                                                                | °R                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 78 | ppm in a mole fraction                                                                                                                                                                                                            | 1000000                                                                                                                                                               | ppm                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 79 | scf in an MMscf                                                                                                                                                                                                                   | 1000000                                                                                                                                                               | scf/MMscf                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 80 | Seconds in a day                                                                                                                                                                                                                  | 86400                                                                                                                                                                 | s/d                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 81 | Cubic feet in a barrel                                                                                                                                                                                                            | 5.614583                                                                                                                                                              | ft³/bbl                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 82 | Inches in a foot                                                                                                                                                                                                                  | 12                                                                                                                                                                    | in/ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 83 | Share of a horizontal vessel's section the gas has (half full)                                                                                                                                                                    | 0.5                                                                                                                                                                   | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 84 | Seam-to-seam over liquid length, horizontal liquid-capacity vessel                                                                                                                                                                | 1.33333333333333                                                                                                                                                      | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 85 | Vertical vessel diameter up to which the fixed allowance applies                                                                                                                                                                  | 36                                                                                                                                                                    | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 86 | Vertical vessel's height above the liquid, up to that diameter                                                                                                                                                                    | 76                                                                                                                                                                    | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 87 | Vertical vessel's height above the liquid, beyond D, past it                                                                                                                                                                      | 40                                                                                                                                                                    | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 88 | API 12J two-phase retention time, low                                                                                                                                                                                             | 1                                                                                                                                                                     | min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 89 | API 12J two-phase retention time, high                                                                                                                                                                                            | 3                                                                                                                                                                     | min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 90 | API 12J three-phase retention time, low                                                                                                                                                                                           | 3                                                                                                                                                                     | min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |
| 91 | API 12J three-phase retention time, high                                                                                                                                                                                          | 30                                                                                                                                                                    | min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                               |                   |                                    |                         |                         |                                                                                                      |   |                  |                               |

## Lambdas

| Name | RefersTo | Comment |
|------|----------|---------|
| PO.SF.Sep.SoudersBrown | =LAMBDA(orientation, qg, p, t, z, sg, rho_l, k_sb, output, IF(OR(AND(orientation<>"Vertical", orientation<>"Horizontal"), qg<=0, p<=0, t<=-459.67, z<=0, sg<=0, k_sb<=0), NA(), LET(tabs, t+459.67, rho_g, 28.9625*sg*p/(10.7316*z*tabs), IF(rho_l<=rho_g, NA(), LET(vel, k_sb*SQRT(MAX(0, rho_l-rho_g)/rho_g), qa, qg*1000000*(14.696/p)*(tabs/519.67)*z/86400, frac, IF(orientation="Vertical", 1, 0.5), IF(output="Velocity", vel, IF(output="Diameter", 12*SQRT(4*qa/(MAX(vel, 0.000001)*frac)/PI()), NA()))))))) | Souders-Brown separator gas capacity: "Velocity" allowable gas velocity (ft/s) = K*sqrt((rho_l-rho_g)/rho_g), or "Diameter" minimum vessel ID (in), "Vertical" or "Horizontal" (half full of liquid). |
| PO.SF.Sep.LiquidRetention | =LAMBDA(phases, orientation, qo, qw, tr_o, tr_w, d, output, IF(OR(AND(phases<>2, phases<>3), AND(orientation<>"Vertical", orientation<>"Horizontal"), qo<0, qw<0, tr_o<0, tr_w<0, d<=0), NA(), IF(OR(output="Volume", output="Length"), IF(phases=2, (qo+qw)*tr_o, qo*tr_o+qw*tr_w)/1440*IF(output="Volume", 1, 5.6145833)/IF(output="Volume", 1, PI()/4*(d/12)^2*IF(orientation="Vertical", 1, 0.5)), NA()))) | Separator liquid retention: "Volume" (bbl) to hold oil qo and water qw (bbl/d) for tr_o/tr_w (min), 2 or 3 phases, or "Length" (ft) of liquid at ID d (in), "Vertical" full section or "Horizontal" half full. |

## Names

| Name | RefersTo | Comment |
|------|----------|---------|
| SEP_Qg | $B$4 | Gas rate, MMscf/d |
| SEP_Qo | $B$5 | Oil rate, STB/d |
| SEP_Qw | $B$6 | Water rate, STB/d |
| SEP_P | $B$7 | Separator operating pressure, absolute, psia |
| SEP_T | $B$8 | Separator operating temperature (after the inlet heater), °F |
| SEP_SG | $B$10 | Gas specific gravity (air = 1), air = 1 |
| SEP_CO2 | $B$11 | CO2 mole fraction, % |
| SEP_H2S | $B$12 | H2S in the gas, ppm |
| SEP_SGL | $B$13 | Liquid specific gravity (oil and water blended), water = 1 |
| SEP_Orient | $B$15 | Orientation (1 horizontal, 2 vertical) |
| SEP_Phases | $B$16 | Phases separated (2 gas-liquid, 3 gas-oil-water) |
| SEP_TrO | $B$17 | Retention time of the oil (of all the liquid if two-phase), min |
| SEP_TrW | $B$18 | Retention time of the water (three-phase), min |
| SEP_K | $B$19 | Souders-Brown K factor for the vessel and mist extractor, ft/s |
| SEP_SRmin | $B$20 | Smallest slenderness, seam-to-seam length over diameter |
| SEP_SRmax | $B$21 | Largest slenderness (about 5 horizontal, 4 vertical) |
| SEP_Dv | $B$23 | Existing vessel's internal diameter, in |
| SEP_Lv | $B$24 | Existing vessel's seam-to-seam length, ft |
| SEP_Inputs | $B$4:$B$24 | The stream's gas, oil and water rates, the operating pressure and temperature, the gas gravity, CO2 and H2S, the liquid gravity, the orientation, phases, retention times, K factor and slenderness limits, and an existing vessel's size |
| SEP_TR | $B$27 | Temperature, absolute, °R |
| SEP_Ppc | $B$28 | Pseudo-critical pressure, p′pc (Standing, Wichert-Aziz), psi |
| SEP_Tpc | $B$29 | Pseudo-critical temperature, T′pc, °R |
| SEP_Z | $B$30 | Z-factor at the separator (DAK) |
| SEP_RhoG | $B$31 | Gas density at the separator, lb/ft³ |
| SEP_RhoL | $B$32 | Liquid density, SGL × water's, lb/ft³ |
| SEP_Vessel | $B$33 | Vessel orientation |
| SEP_Vt | $B$34 | Allowable gas velocity, Vt = K·√((ρl − ρg)/ρg), ft/s |
| SEP_Qa | $B$35 | Gas flow at the separator, ft³/s |
| SEP_Dgas | $B$36 | Smallest diameter for the gas, in |
| SEP_Vliq | $B$38 | Liquid held for the retention times, bbl |
| SEP_QL | $B$39 | Liquid rate, oil and water, STB/d |
| SEP_Dstd | $B$41 | Smallest standard diameter that carries the gas, in |
| SEP_Drec | $B$42 | Recommended diameter, the smallest within the slenderness, in |
| SEP_Leff | $B$43 | Liquid length in it, effective (horizontal) or height (vertical), ft |
| SEP_Lss | $B$44 | Seam-to-seam length, ft |
| SEP_SR | $B$45 | Slenderness, 12·Lss/D |
| SEP_Governs | $B$46 | What sets the diameter |
| SEP_Vg | $B$47 | Gas velocity in it, ft/s |
| SEP_VgRatio | $B$48 | Gas velocity over the allowable, Vg/Vt |
| SEP_LvLiq | $B$50 | Liquid length it has, from its seam-to-seam length, ft |
| SEP_LvNeed | $B$51 | Liquid length the duty needs at its diameter, ft |
| SEP_TrAvail | $B$52 | Oil retention time it gives (all the liquid's if two-phase), min |
| SEP_SizeCheck | $B$53 | Slenderness check verdict |
| SEP_SizeCheckNote | $C$53 | Slenderness check comment |
| SEP_RetentionCheck | $B$54 | Retention time check verdict |
| SEP_RetentionCheckNote | $C$54 | Retention time check comment |
| SEP_ExistingCheck | $B$55 | Existing vessel check verdict |
| SEP_ExistingCheckNote | $C$55 | Existing vessel check comment |
| SEP_Results | $B$27:$B$55 | Z, the gas and liquid densities, the Souders-Brown velocity and gas-capacity diameter, the liquid held, the recommended vessel's diameter, liquid and seam-to-seam lengths and slenderness, the existing vessel's rating, and the three checks |
| SEP_Curve | $A$62:$I$74 | Each standard vessel diameter: whether it carries the gas, its liquid length for the retention times, its seam-to-seam length and slenderness, whether it fits, the lengths at the smallest and largest slenderness, and a verdict |
| SEP_R0 | $B$77 | Rankine at 0 °F, °R |
| SEP_Ppm | $B$78 | ppm in a mole fraction, ppm |
| SEP_Scf | $B$79 | scf in an MMscf, scf/MMscf |
| SEP_Sec | $B$80 | Seconds in a day, s/d |
| SEP_Ft3Bbl | $B$81 | Cubic feet in a barrel, ft³/bbl |
| SEP_InFt | $B$82 | Inches in a foot, in/ft |
| SEP_Half | $B$83 | Share of a horizontal vessel's section the gas has (half full) |
| SEP_Shell | $B$84 | Seam-to-seam over liquid length, horizontal liquid-capacity vessel |
| SEP_VertD | $B$85 | Vertical vessel diameter up to which the fixed allowance applies, in |
| SEP_VertA | $B$86 | Vertical vessel's height above the liquid, up to that diameter, in |
| SEP_VertB | $B$87 | Vertical vessel's height above the liquid, beyond D, past it, in |
| SEP_Tr2Lo | $B$88 | API 12J two-phase retention time, low, min |
| SEP_Tr2Hi | $B$89 | API 12J two-phase retention time, high, min |
| SEP_Tr3Lo | $B$90 | API 12J three-phase retention time, low, min |
| SEP_Tr3Hi | $B$91 | API 12J three-phase retention time, high, min |

---

## Related Blueprints
- [Multiphase Flowline by Beggs and Brill](/blueprint/po.sf.multiphase.flowline.md)
- [Compressor Staging and Power](/blueprint/po.sf.compressor.power.md)
- [Liquid Pipeline Sizing with Elevation and Pump NPSH](/blueprint/po.sf.pipeline.liquid.md)
- [Wellhead Choke Sizing](/blueprint/po.sf.choke.sizing.md)
- [Gas Pipeline Sizing by Weymouth and Panhandle](/blueprint/po.sf.gas.pipeline.sizing.md)
- [Erosional Velocity of a Multiphase Line (API RP 14E)](/blueprint/po.fa.erosion.analysis.md)

