---
cid: po.bp.pp.sw.shaly
hub: pp
tags: [petrophysics, water-saturation, shaly-sand, Simandoux, Indonesia, Waxman-Smits, dual-water, Archie, Qv, cation-exchange-capacity, bound-water, hydrocarbon-pore-thickness, quick-look]
facets: { discipline: reservoir, property: saturation, method-type: empirical }
title: Shaly-Sand Water Saturation
summary: "How much water a shaly sand holds by Simandoux, Indonesia, Waxman-Smits and dual water against Archie, and the hydrocarbon each model finds."
slug: po.pp.sw.shaly
type: worksheet
---

# Shaly-Sand Water Saturation

## Description

How much water is in a shaly sand, and how much does the model change the answer? In a shaly sand the clay conducts as well as the brine, so Archie reads too much water. You enter Archie's parameters, Rw, the shale's resistivity, density and cation exchange capacity, the formation temperature, a zone and the cutoffs, over a gamma-ray, density and deep-resistivity log. You read off water saturation at every depth by Simandoux, Indonesia, Waxman-Smits, dual water and Archie, and the hydrocarbon each model finds in the zone and over the log.

**Parameters:**
- **Archie**: `SS_a`, `SS_m`, `SS_n` (m* and n* for Waxman-Smits) and Rw at formation temperature `SS_Rw` (ohm·m)
- **Shale**: its resistivity `SS_Rsh` (ohm·m), the gamma-ray picks `SS_GRcl`, `SS_GRsh` (API), its bulk density `SS_RhoSh` (g/cm³) and its cation exchange capacity `SS_CECsh` (meq/100 g)
- **Rock and temperature**: the matrix and grain density `SS_RhoMa` and fluid density `SS_RhoF` (g/cm³), and the formation temperature `SS_Tf` (°F)
- **Zone and cutoffs**: the zone's top and base `SS_ZTop`, `SS_ZBase` (ft), the reservoir cutoffs on shale volume `SS_VshCut` and effective porosity `SS_PhiCut`, and the agreement limit `SS_Tol`
- **Log**: depth, GR, bulk density and deep resistivity in the log table, every 2 ft

**How to use it:** The log is synthetic. Paste your depth, gamma ray, bulk density and deep resistivity (corrected for invasion) over the log table. Read Rsh and the shale's density in a thick shale on the same log. Take the CEC from core, scaled to the sand by its shale volume or measured on it, and m* and n* from shaly-sand core. Where the models disagree, a core saturation (Dean-Stark) or a capillary-pressure model decides between them. A log track draws Sw by all six against depth.

**Method:** The models fall in two families. The shale-volume models, Simandoux and Indonesia, add a conductive shale of resistivity Rsh in proportion to Vsh. They work on effective porosity and reduce to Archie on effective porosity with no shale. The clay-conductance models work on total porosity and reduce to Archie on total porosity with no clay. Waxman-Smits puts the clay's conductivity in its exchange cations, Qv from the cation exchange capacity, with B from Juhasz's fit at formation temperature. Dual water treats the clay-bound water as a second water of its own resistivity Rwb. Both Archies are on the sheet, each beside the models that reduce to it. Their saturations are of different porosities, so the comparison is on the hydrocarbon each model finds, φ (1 − Sw) in its own porosity, a volume of rock that does not depend on the porosity it is counted in.

- **Shale volume and porosity.** Vsh is the linear gamma-ray index, kept between 0 and 1. Total porosity is the density porosity φt = (ρma − ρb) / (ρma − ρf), and the shale's total porosity φtsh is the same from its density. Effective porosity is φe = φt − Vsh φtsh. A sample is reservoir when Vsh is at most the cutoff and φe at least its cutoff; any other sample reads Sw = 1.
- **Archie:** Sw = (a Rw / (φ^m Rt))^(1/n), on φe and on φt.
- **Simandoux:** Sw = (0.4 Rw / φe²) [−Vsh/Rsh + √((Vsh/Rsh)² + 5 φe² / (Rw Rt))].
- **Indonesia:** 1/√Rt = [Vsh^(1 − Vsh/2) / √Rsh + φe^(m/2) / √(a Rw)] Sw^(n/2).
- **Waxman-Smits:** 1/Rt = (φt^m / a) (Sw^n / Rw + B Qv Sw^(n−1)). Qv = CEC (1 − φt) ρg / (100 φt), with the sand's CEC Vsh × CECsh. B is Juhasz's fit, B = (−1.28 + 0.225 T − 0.0004059 T²) / (1 + Rw^1.23 (0.045 T − 0.27)), T in °C.
- **Dual water:** 1/Rt = (φt^m Sw^n / a) [1/Rw + (1/Rwb − 1/Rw) Swb/Sw]. The bound water's resistivity is Rwb = Rsh φtsh^m / a, the shale's water, and its saturation Swb = Vsh φtsh / φt.
- **Solution.** Waxman-Smits and dual water are solved in closed form at n = 2 and by Newton's method otherwise. Each saturation is shown at most 1. The zone's values are the means of its reservoir samples. The hydrocarbon pore thickness of a model is Σ φ (1 − Sw) times the sample spacing, in that model's porosity.
- **Checks.** Two checks give PASS or WARN. The Archie check warns when Archie on effective porosity finds less hydrocarbon in the zone than the shaly-sand models' mean by more than the agreement limit. The agreement check warns when the four shaly-sand models' hydrocarbon pore thickness over the log spreads by more than that limit.

**Example:** The default case is the Well-Log Display workbook's synthetic interval, from 5,010 to 5,100 ft every 2 ft: the reservoir part, from the shale above the clean oil sand to the shale below the water sand. Its parameters are the workbook's: a, m and n of 1, 2 and 2, Rw 0.05 ohm·m and Rsh 2.4 ohm·m, gamma-ray picks of 30 and 115 API, a 2.65 g/cm³ sandstone and 1.0 g/cm³ filtrate, and reservoir cutoffs of 0.40 Vsh and 10% effective porosity. The shale reads 2.48 g/cm³, and its CEC is taken as 8 meq/100 g, an illitic shale. The formation is at 145°F. The zone is the shaly sand above its oil–water contact, a foot inside its top and base, 5,041 to 5,048 ft. The models have to agree within 15%.

The shale's total porosity is (2.65 − 2.48) / 1.65 = 10.3%, so Rwb = 2.4 × 0.1030² = 0.0255 ohm·m. At 145°F, 62.8°C, Juhasz's B is (−1.28 + 14.125 − 1.600) / (1 + 0.0251 × 2.555) = 10.57 (S/m)/(meq/cm³). In the zone, 5,042 ft is above the 0.40 Vsh cutoff, so three samples count, from 5,044 to 5,048 ft. Their mean Vsh is 0.367, total porosity 19.4%, effective porosity 15.6%, Qv 0.324 meq/cm³ and bound-water saturation 19.5%. Archie on effective porosity reads 38.3% water. Simandoux reads 23.9% and Indonesia 27.2%. On total porosity Archie reads 30.8%, Waxman-Smits 23.4% and dual water 22.8%. In hydrocarbon volume Archie on effective porosity finds 0.096 against the four shaly-sand models' mean of 0.132, 27% less: the Archie check warns, which is the point of the sheet. Over the log the clean oil sand carries most of the hydrocarbon, where the models agree. The pore thickness is 5.24 ft by Archie on effective porosity and 5.59 ft on total porosity, 5.85 ft by Simandoux, 5.43 ft by Indonesia, 5.73 ft by Waxman-Smits and 5.75 ft by dual water. The four shaly-sand models spread 7%, within 15%, so the agreement check passes. With no CEC, Waxman-Smits reads the zone as Archie on total porosity does, 30.8%. In the clean oil sand from 5,013 to 5,033 ft Archie is within the limit and the Archie check passes. A 5% agreement limit makes the agreement check warn. At n = 2.2 Waxman-Smits and dual water are solved by Newton's method and read 27.5% and 27.0%, against 34.3% by Archie on total porosity.

## Validity

Each model is an empirical description of how clay conducts. None is right in every shaly sand, and they can differ by tens of saturation units in the shaliest beds, as here. Simandoux and Indonesia take the shale volume as the clay indicator and the thick shale's resistivity as the clay's; dispersed clay in the pores conducts differently from laminated shale. The catalog's Simandoux has its constants 0.4 and 5 built in, the form for a = 0.8 with m = n = 2, so with no shale it reads 0.894 of Archie at a = 1, and in the clean water sand it reads below 100% water. Waxman-Smits needs Qv, best from core CEC; scaling a shale CEC by Vsh is a field shortcut, and B from Juhasz's fit is for sodium-chloride brines. Dual water takes the bound water from the shale; where the log's Rt is high for the shale's terms, its total saturation can fall to the bound-water saturation, which leaves no free water. The interval is synthetic. Field units.

Named alternatives: a laminated model (Thomas-Stieber or Poupon) for laminated sand–shale sequences; the Archie Water Saturation and Bulk Volume Water sheet for a clean sand.

## References

- Simandoux, P. (1963). Mesures diélectriques en milieu poreux, application à la mesure des saturations en eau. *Revue de l'Institut Français du Pétrole*, special issue (the Simandoux equation).
- Poupon, A. and Leveaux, J. (1971). Evaluation of Water Saturation in Shaly Formations. SPWLA 12th Annual Logging Symposium, paper O (the Indonesia equation).
- Waxman, M.H. and Smits, L.J.M. (1968). Electrical Conductivities in Oil-Bearing Shaly Sands. *SPE Journal* 8(2), 107–122, SPE-1863-A.
- Juhasz, I. (1981). Normalised Qv, the Key to Shaly Sand Evaluation Using the Waxman-Smits Equation in the Absence of Core Data. SPWLA 22nd Annual Logging Symposium, paper Z (B as a function of temperature and Rw).
- Clavier, C., Coates, G. and Dumanoir, J. (1984). Theoretical and Experimental Bases for the Dual-Water Model for Interpretation of Shaly Sands. *SPE Journal* 24(2), 153–168, SPE-6859-PA.
- Bassiouni, Z. (1994). *Theory, Measurement, and Interpretation of Well Logs*. SPE Textbook Series Vol. 4, ch. 16 (shaly-sand interpretation).

## Functions used

`PO.PP.Vsh.GammaRayIndex`, `PO.PP.Porosity.FromDensity`, `PO.PP.Sw.Archie`, `PO.PP.Sw.Simandoux`, `PO.PP.Sw.Indonesia`, `PO.PP.Qv.FromCEC`, `PO.PP.Sw.WaxmanSmits`, `PO.PP.Sw.DualWater`

## Spreadsheet: SwShaly

|     | A                                                                                                                                                                                                                                  | B                                                                                                         | C                                                                                                                                                                                                                                                                                                                                       | D          | E                                                            | F                                                         | G                           | H                                             | I                                                           | J                                 | K                                                                    | L                                                                    | M                                                                                   | N                                                                    | O                                                                                           | P                                                                                                      |
|-----|------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|-----------------------------------------------------------------------------------------------------------|-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|------------|--------------------------------------------------------------|-----------------------------------------------------------|-----------------------------|-----------------------------------------------|-------------------------------------------------------------|-----------------------------------|----------------------------------------------------------------------|----------------------------------------------------------------------|-------------------------------------------------------------------------------------|----------------------------------------------------------------------|---------------------------------------------------------------------------------------------|--------------------------------------------------------------------------------------------------------|
| 1   | Shaly-Sand Water Saturation                                                                                                                                                                                                        |                                                                                                           | Petroleum Office                                                                                                                                                                                                                                                                                                                        |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 2   | Blue cells on yellow are inputs. Set Archie's parameters, Rw, the shale's readings and CEC, the temperature, the zone and the cutoffs; paste your own GR, density and deep resistivity over the log below.                         |                                                                                                           |                                                                                                                                                                                                                                                                                                                                         |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 3   | Archie's Parameters, the Water, the Shale, the Zone and the Cutoffs                                                                                                                                                                |                                                                                                           |                                                                                                                                                                                                                                                                                                                                         |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 4   | Tortuosity factor a                                                                                                                                                                                                                | 1                                                                                                         | —                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 5   | Cementation exponent m (m* for Waxman-Smits)                                                                                                                                                                                       | 2                                                                                                         | —                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 6   | Saturation exponent n (n* for Waxman-Smits)                                                                                                                                                                                        | 2                                                                                                         | —                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 7   | Formation-water resistivity at formation temperature                                                                                                                                                                               | 0.05                                                                                                      | ohm·m                                                                                                                                                                                                                                                                                                                                   |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 8   | Shale resistivity, read in a thick shale                                                                                                                                                                                           | 2.4                                                                                                       | ohm·m                                                                                                                                                                                                                                                                                                                                   |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 9   | Clean-sand gamma ray (Vsh = 0)                                                                                                                                                                                                     | 30                                                                                                        | API                                                                                                                                                                                                                                                                                                                                     |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 10  | Shale gamma ray (Vsh = 1)                                                                                                                                                                                                          | 115                                                                                                       | API                                                                                                                                                                                                                                                                                                                                     |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 11  | Matrix and grain density (sandstone)                                                                                                                                                                                               | 2.65                                                                                                      | g/cm³                                                                                                                                                                                                                                                                                                                                   |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 12  | Fluid density (fresh mud filtrate)                                                                                                                                                                                                 | 1                                                                                                         | g/cm³                                                                                                                                                                                                                                                                                                                                   |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 13  | Shale bulk density                                                                                                                                                                                                                 | 2.48                                                                                                      | g/cm³                                                                                                                                                                                                                                                                                                                                   |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 14  | Shale cation exchange capacity (core), scaled by Vsh in the sand                                                                                                                                                                   | 8                                                                                                         | meq/100 g                                                                                                                                                                                                                                                                                                                               |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 15  | Formation temperature                                                                                                                                                                                                              | 145                                                                                                       | °F                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 16  | Zone top (the shaly oil sand, a foot inside)                                                                                                                                                                                       | 5041                                                                                                      | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 17  | Zone base (a foot inside the bed's base)                                                                                                                                                                                           | 5048                                                                                                      | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 18  | Shale-volume cutoff for reservoir                                                                                                                                                                                                  | 0.4                                                                                                       | v/v                                                                                                                                                                                                                                                                                                                                     |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 19  | Effective-porosity cutoff for reservoir                                                                                                                                                                                            | 0.1                                                                                                       | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 20  | Agreement limit between models, on hydrocarbon volume                                                                                                                                                                              | 0.15                                                                                                      | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 23  | The Shale's Terms, the Zone's Saturation by Model, and the Hydrocarbon by Model                                                                                                                                                    |                                                                                                           |                                                                                                                                                                                                                                                                                                                                         |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 24  | Shale total porosity (density)                                                                                                                                                                                                     | =PO.PP.Porosity.FromDensity(SS_RhoMa,SS_RhoSh,SS_RhoF)                                                    | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 25  | Bound-water resistivity Rwb = Rsh φtsh^m / a                                                                                                                                                                                       | =SS_Rsh*SS_PhiTsh^SS_m/SS_a                                                                               | ohm·m                                                                                                                                                                                                                                                                                                                                   |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 26  | Formation temperature                                                                                                                                                                                                              | =(SS_Tf-SS_TfZero)/SS_TfPerC                                                                              | °C                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 27  | Waxman-Smits B at formation temperature and Rw (Juhasz)                                                                                                                                                                            | =(SS_J1+SS_J2*SS_TfC-SS_J3*SS_TfC^2)/(1+SS_Rw^SS_J4*(SS_J5*SS_TfC-SS_J6))                                 | (S/m)/(meq/cm³)                                                                                                                                                                                                                                                                                                                         |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 28  | Solve: 1 closed form (n = 2), 2 Newton                                                                                                                                                                                             | =IF(SS_n=2,1,2)                                                                                           | —                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 29  | Zone mean shale volume (reservoir samples)                                                                                                                                                                                         | =AVERAGEIFS($E$70:$E$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | v/v                                                                                                                                                                                                                                                                                                                                     |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 30  | Zone mean total porosity                                                                                                                                                                                                           | =AVERAGEIFS($F$70:$F$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 31  | Zone mean effective porosity                                                                                                                                                                                                       | =AVERAGEIFS($G$70:$G$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 32  | Zone mean Qv                                                                                                                                                                                                                       | =AVERAGEIFS($I$70:$I$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | meq/cm³                                                                                                                                                                                                                                                                                                                                 |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 33  | Zone mean bound-water saturation                                                                                                                                                                                                   | =AVERAGEIFS($J$70:$J$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 34  | Log sample spacing                                                                                                                                                                                                                 | =(MAX($A$70:$A$115)-MIN($A$70:$A$115))/(COUNT($A$70:$A$115)-1)                                            | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 35  | Clay-bound water thickness over the log, Σ φt Swb                                                                                                                                                                                  | =SUMPRODUCT($F$70:$F$115,$J$70:$J$115)*SS_Step                                                            | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 36  | Zone Sw, Archie (φe)                                                                                                                                                                                                               | =AVERAGEIFS($K$70:$K$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 37  | Zone Sw, Simandoux (φe)                                                                                                                                                                                                            | =AVERAGEIFS($L$70:$L$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 38  | Zone Sw, Indonesia (φe)                                                                                                                                                                                                            | =AVERAGEIFS($M$70:$M$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 39  | Zone Sw, Archie (φt)                                                                                                                                                                                                               | =AVERAGEIFS($N$70:$N$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 40  | Zone Sw, Waxman-Smits (φt)                                                                                                                                                                                                         | =AVERAGEIFS($O$70:$O$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 41  | Zone Sw, Dual water (φt)                                                                                                                                                                                                           | =AVERAGEIFS($P$70:$P$115,$A$70:$A$115,">="&SS_ZTop,$A$70:$A$115,"<="&SS_ZBase,$H$70:$H$115,1)             | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 42  | Zone hydrocarbon volume, Archie on effective porosity                                                                                                                                                                              | =SS_ZPhiE*(1-SS_ZSwA)                                                                                     | v/v                                                                                                                                                                                                                                                                                                                                     |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 43  | Zone hydrocarbon volume, the four shaly-sand models' mean                                                                                                                                                                          | =AVERAGE(SS_ZPhiE*(1-SS_ZSwS),SS_ZPhiE*(1-SS_ZSwI),SS_ZPhiT*(1-SS_ZSwW),SS_ZPhiT*(1-SS_ZSwD))             | v/v                                                                                                                                                                                                                                                                                                                                     |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 44  | Archie's shortfall in the zone against that mean                                                                                                                                                                                   | =1-SS_ZHcA/SS_ZHcShaly                                                                                    | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 45  | Hydrocarbon pore thickness over the log, Archie (φe)                                                                                                                                                                               | =(SUM($G$70:$G$115)-SUMPRODUCT($G$70:$G$115,$K$70:$K$115))*SS_Step                                        | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 46  | Hydrocarbon pore thickness over the log, Simandoux (φe)                                                                                                                                                                            | =(SUM($G$70:$G$115)-SUMPRODUCT($G$70:$G$115,$L$70:$L$115))*SS_Step                                        | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 47  | Hydrocarbon pore thickness over the log, Indonesia (φe)                                                                                                                                                                            | =(SUM($G$70:$G$115)-SUMPRODUCT($G$70:$G$115,$M$70:$M$115))*SS_Step                                        | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 48  | Hydrocarbon pore thickness over the log, Archie (φt)                                                                                                                                                                               | =(SUM($F$70:$F$115)-SUMPRODUCT($F$70:$F$115,$N$70:$N$115))*SS_Step                                        | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 49  | Hydrocarbon pore thickness over the log, Waxman-Smits (φt)                                                                                                                                                                         | =(SUM($F$70:$F$115)-SUMPRODUCT($F$70:$F$115,$O$70:$O$115))*SS_Step                                        | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 50  | Hydrocarbon pore thickness over the log, Dual water (φt)                                                                                                                                                                           | =(SUM($F$70:$F$115)-SUMPRODUCT($F$70:$F$115,$P$70:$P$115))*SS_Step                                        | ft                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 51  | Spread of the four shaly-sand models over the log                                                                                                                                                                                  | =(MAX(SS_HcS,SS_HcI,SS_HcW,SS_HcD)-MIN(SS_HcS,SS_HcI,SS_HcW,SS_HcD))/AVERAGE(SS_HcS,SS_HcI,SS_HcW,SS_HcD) | %                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 52  | Archie in the zone check                                                                                                                                                                                                           | =IF(SS_Short<=SS_Tol,"PASS","WARN")                                                                       | =IF(SS_Short<=SS_Tol,"Archie on effective porosity finds within "&FIXED(SS_Tol*100,0)&"% of the shaly-sand models' hydrocarbon in the zone: it is clean enough for Archie","Archie on effective porosity finds "&FIXED(SS_Short*100,0)&"% less hydrocarbon in the zone than the shaly-sand models do: report a shaly-sand model there") |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 53  | Model agreement check                                                                                                                                                                                                              | =IF(SS_Spread<=SS_Tol,"PASS","WARN")                                                                      | =IF(SS_Spread<=SS_Tol,"the four shaly-sand models' hydrocarbon pore thickness over the log agrees within "&FIXED(SS_Spread*100,0)&"%","the four shaly-sand models' hydrocarbon pore thickness over the log spreads "&FIXED(SS_Spread*100,0)&"%: calibrate them to core saturations before choosing one")                                |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 55  | How to use it: paste your depth, GR, bulk density and deep resistivity (corrected for invasion) over the log table, read Rsh and the shale's density in a thick shale, take the CEC from core, and m* and n* from shaly-sand core. |                                                                                                           |                                                                                                                                                                                                                                                                                                                                         |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 56  | The log is synthetic, the log display workbook's interval. The models disagree most in the shaly beds; there a core Sw (Dean-Stark) or a capillary-pressure model decides between them.                                            |                                                                                                           |                                                                                                                                                                                                                                                                                                                                         |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 58  | Constants (Juhasz's B, with T in °C)                                                                                                                                                                                               |                                                                                                           |                                                                                                                                                                                                                                                                                                                                         |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 59  | Water's freezing point                                                                                                                                                                                                             | 32                                                                                                        | °F                                                                                                                                                                                                                                                                                                                                      |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 60  | Fahrenheit degrees per Celsius degree                                                                                                                                                                                              | 1.8                                                                                                       | °F/°C                                                                                                                                                                                                                                                                                                                                   |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 61  | Juhasz B, constant term                                                                                                                                                                                                            | -1.28                                                                                                     | —                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 62  | Juhasz B, temperature term                                                                                                                                                                                                         | 0.225                                                                                                     | 1/°C                                                                                                                                                                                                                                                                                                                                    |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 63  | Juhasz B, temperature-squared term                                                                                                                                                                                                 | 0.0004059                                                                                                 | 1/°C²                                                                                                                                                                                                                                                                                                                                   |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 64  | Juhasz B, exponent of Rw                                                                                                                                                                                                           | 1.23                                                                                                      | —                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 65  | Juhasz B, Rw term's temperature slope                                                                                                                                                                                              | 0.045                                                                                                     | 1/°C                                                                                                                                                                                                                                                                                                                                    |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 66  | Juhasz B, Rw term's constant                                                                                                                                                                                                       | 0.27                                                                                                      | —                                                                                                                                                                                                                                                                                                                                       |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 68  | Log: Readings and Water Saturation by Model (the log display workbook's interval, 5,010 to 5,100 ft every 2 ft)                                                                                                                    |                                                                                                           |                                                                                                                                                                                                                                                                                                                                         |            |                                                              |                                                           |                             |                                               |                                                             |                                   |                                                                      |                                                                      |                                                                                     |                                                                      |                                                                                             |                                                                                                        |
| 69  | Depth (ft)                                                                                                                                                                                                                         | GR (API)                                                                                                  | RHOB (g/cm³)                                                                                                                                                                                                                                                                                                                            | Rt (ohm·m) | Vsh (v/v)                                                    | φ total (%)                                               | φ effective (%)             | Reservoir                                     | Qv (meq/cm³)                                                | Swb (%)                           | Archie (φe) (%)                                                      | Simandoux (φe) (%)                                                   | Indonesia (φe) (%)                                                                  | Archie (φt) (%)                                                      | Waxman-Smits (φt) (%)                                                                       | Dual water (φt) (%)                                                                                    |
| 70  | 5010                                                                                                                                                                                                                               | 108.4                                                                                                     | 2.462                                                                                                                                                                                                                                                                                                                                   | 3.27       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B70,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C70,SS_RhoF))  | =MAX(0,F70-E70*SS_PhiTsh)   | =IF(AND(G70>=SS_PhiCut,E70<=SS_VshCut),1,0)   | =IF(H70=1,PO.PP.Qv.FromCEC(E70*SS_CECsh,F70,SS_RhoMa),0)    | =IF(H70=1,E70*SS_PhiTsh/F70,0)    | =IF(H70=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G70,SS_Rw,D70)),1)    | =IF(H70=1,MIN(1,PO.PP.Sw.Simandoux(G70,D70,SS_Rw,E70,SS_Rsh)),1)     | =IF(H70=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G70,SS_Rw,D70,E70,SS_Rsh)),1)     | =IF(H70=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F70,SS_Rw,D70)),1)    | =IF(H70=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F70,SS_Rw,D70,SS_B,I70,SS_Mode)),1)     | =IF(H70=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F70,SS_Rw,SS_Rwb,J70,D70,SS_Mode),1,1)),1)     |
| 71  | 5012                                                                                                                                                                                                                               | 73.9                                                                                                      | 2.339                                                                                                                                                                                                                                                                                                                                   | 10         | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B71,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C71,SS_RhoF))  | =MAX(0,F71-E71*SS_PhiTsh)   | =IF(AND(G71>=SS_PhiCut,E71<=SS_VshCut),1,0)   | =IF(H71=1,PO.PP.Qv.FromCEC(E71*SS_CECsh,F71,SS_RhoMa),0)    | =IF(H71=1,E71*SS_PhiTsh/F71,0)    | =IF(H71=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G71,SS_Rw,D71)),1)    | =IF(H71=1,MIN(1,PO.PP.Sw.Simandoux(G71,D71,SS_Rw,E71,SS_Rsh)),1)     | =IF(H71=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G71,SS_Rw,D71,E71,SS_Rsh)),1)     | =IF(H71=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F71,SS_Rw,D71)),1)    | =IF(H71=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F71,SS_Rw,D71,SS_B,I71,SS_Mode)),1)     | =IF(H71=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F71,SS_Rw,SS_Rwb,J71,D71,SS_Mode),1,1)),1)     |
| 72  | 5014                                                                                                                                                                                                                               | 35.2                                                                                                      | 2.237                                                                                                                                                                                                                                                                                                                                   | 41.2       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B72,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C72,SS_RhoF))  | =MAX(0,F72-E72*SS_PhiTsh)   | =IF(AND(G72>=SS_PhiCut,E72<=SS_VshCut),1,0)   | =IF(H72=1,PO.PP.Qv.FromCEC(E72*SS_CECsh,F72,SS_RhoMa),0)    | =IF(H72=1,E72*SS_PhiTsh/F72,0)    | =IF(H72=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G72,SS_Rw,D72)),1)    | =IF(H72=1,MIN(1,PO.PP.Sw.Simandoux(G72,D72,SS_Rw,E72,SS_Rsh)),1)     | =IF(H72=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G72,SS_Rw,D72,E72,SS_Rsh)),1)     | =IF(H72=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F72,SS_Rw,D72)),1)    | =IF(H72=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F72,SS_Rw,D72,SS_B,I72,SS_Mode)),1)     | =IF(H72=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F72,SS_Rw,SS_Rwb,J72,D72,SS_Mode),1,1)),1)     |
| 73  | 5016                                                                                                                                                                                                                               | 36.1                                                                                                      | 2.209                                                                                                                                                                                                                                                                                                                                   | 46.3       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B73,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C73,SS_RhoF))  | =MAX(0,F73-E73*SS_PhiTsh)   | =IF(AND(G73>=SS_PhiCut,E73<=SS_VshCut),1,0)   | =IF(H73=1,PO.PP.Qv.FromCEC(E73*SS_CECsh,F73,SS_RhoMa),0)    | =IF(H73=1,E73*SS_PhiTsh/F73,0)    | =IF(H73=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G73,SS_Rw,D73)),1)    | =IF(H73=1,MIN(1,PO.PP.Sw.Simandoux(G73,D73,SS_Rw,E73,SS_Rsh)),1)     | =IF(H73=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G73,SS_Rw,D73,E73,SS_Rsh)),1)     | =IF(H73=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F73,SS_Rw,D73)),1)    | =IF(H73=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F73,SS_Rw,D73,SS_B,I73,SS_Mode)),1)     | =IF(H73=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F73,SS_Rw,SS_Rwb,J73,D73,SS_Mode),1,1)),1)     |
| 74  | 5018                                                                                                                                                                                                                               | 29.5                                                                                                      | 2.212                                                                                                                                                                                                                                                                                                                                   | 50.6       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B74,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C74,SS_RhoF))  | =MAX(0,F74-E74*SS_PhiTsh)   | =IF(AND(G74>=SS_PhiCut,E74<=SS_VshCut),1,0)   | =IF(H74=1,PO.PP.Qv.FromCEC(E74*SS_CECsh,F74,SS_RhoMa),0)    | =IF(H74=1,E74*SS_PhiTsh/F74,0)    | =IF(H74=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G74,SS_Rw,D74)),1)    | =IF(H74=1,MIN(1,PO.PP.Sw.Simandoux(G74,D74,SS_Rw,E74,SS_Rsh)),1)     | =IF(H74=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G74,SS_Rw,D74,E74,SS_Rsh)),1)     | =IF(H74=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F74,SS_Rw,D74)),1)    | =IF(H74=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F74,SS_Rw,D74,SS_B,I74,SS_Mode)),1)     | =IF(H74=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F74,SS_Rw,SS_Rwb,J74,D74,SS_Mode),1,1)),1)     |
| 75  | 5020                                                                                                                                                                                                                               | 33.4                                                                                                      | 2.21                                                                                                                                                                                                                                                                                                                                    | 44.8       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B75,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C75,SS_RhoF))  | =MAX(0,F75-E75*SS_PhiTsh)   | =IF(AND(G75>=SS_PhiCut,E75<=SS_VshCut),1,0)   | =IF(H75=1,PO.PP.Qv.FromCEC(E75*SS_CECsh,F75,SS_RhoMa),0)    | =IF(H75=1,E75*SS_PhiTsh/F75,0)    | =IF(H75=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G75,SS_Rw,D75)),1)    | =IF(H75=1,MIN(1,PO.PP.Sw.Simandoux(G75,D75,SS_Rw,E75,SS_Rsh)),1)     | =IF(H75=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G75,SS_Rw,D75,E75,SS_Rsh)),1)     | =IF(H75=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F75,SS_Rw,D75)),1)    | =IF(H75=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F75,SS_Rw,D75,SS_B,I75,SS_Mode)),1)     | =IF(H75=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F75,SS_Rw,SS_Rwb,J75,D75,SS_Mode),1,1)),1)     |
| 76  | 5022                                                                                                                                                                                                                               | 31.1                                                                                                      | 2.214                                                                                                                                                                                                                                                                                                                                   | 52.3       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B76,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C76,SS_RhoF))  | =MAX(0,F76-E76*SS_PhiTsh)   | =IF(AND(G76>=SS_PhiCut,E76<=SS_VshCut),1,0)   | =IF(H76=1,PO.PP.Qv.FromCEC(E76*SS_CECsh,F76,SS_RhoMa),0)    | =IF(H76=1,E76*SS_PhiTsh/F76,0)    | =IF(H76=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G76,SS_Rw,D76)),1)    | =IF(H76=1,MIN(1,PO.PP.Sw.Simandoux(G76,D76,SS_Rw,E76,SS_Rsh)),1)     | =IF(H76=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G76,SS_Rw,D76,E76,SS_Rsh)),1)     | =IF(H76=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F76,SS_Rw,D76)),1)    | =IF(H76=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F76,SS_Rw,D76,SS_B,I76,SS_Mode)),1)     | =IF(H76=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F76,SS_Rw,SS_Rwb,J76,D76,SS_Mode),1,1)),1)     |
| 77  | 5024                                                                                                                                                                                                                               | 35                                                                                                        | 2.209                                                                                                                                                                                                                                                                                                                                   | 46.1       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B77,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C77,SS_RhoF))  | =MAX(0,F77-E77*SS_PhiTsh)   | =IF(AND(G77>=SS_PhiCut,E77<=SS_VshCut),1,0)   | =IF(H77=1,PO.PP.Qv.FromCEC(E77*SS_CECsh,F77,SS_RhoMa),0)    | =IF(H77=1,E77*SS_PhiTsh/F77,0)    | =IF(H77=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G77,SS_Rw,D77)),1)    | =IF(H77=1,MIN(1,PO.PP.Sw.Simandoux(G77,D77,SS_Rw,E77,SS_Rsh)),1)     | =IF(H77=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G77,SS_Rw,D77,E77,SS_Rsh)),1)     | =IF(H77=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F77,SS_Rw,D77)),1)    | =IF(H77=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F77,SS_Rw,D77,SS_B,I77,SS_Mode)),1)     | =IF(H77=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F77,SS_Rw,SS_Rwb,J77,D77,SS_Mode),1,1)),1)     |
| 78  | 5026                                                                                                                                                                                                                               | 29.8                                                                                                      | 2.21                                                                                                                                                                                                                                                                                                                                    | 47.4       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B78,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C78,SS_RhoF))  | =MAX(0,F78-E78*SS_PhiTsh)   | =IF(AND(G78>=SS_PhiCut,E78<=SS_VshCut),1,0)   | =IF(H78=1,PO.PP.Qv.FromCEC(E78*SS_CECsh,F78,SS_RhoMa),0)    | =IF(H78=1,E78*SS_PhiTsh/F78,0)    | =IF(H78=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G78,SS_Rw,D78)),1)    | =IF(H78=1,MIN(1,PO.PP.Sw.Simandoux(G78,D78,SS_Rw,E78,SS_Rsh)),1)     | =IF(H78=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G78,SS_Rw,D78,E78,SS_Rsh)),1)     | =IF(H78=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F78,SS_Rw,D78)),1)    | =IF(H78=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F78,SS_Rw,D78,SS_B,I78,SS_Mode)),1)     | =IF(H78=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F78,SS_Rw,SS_Rwb,J78,D78,SS_Mode),1,1)),1)     |
| 79  | 5028                                                                                                                                                                                                                               | 34                                                                                                        | 2.216                                                                                                                                                                                                                                                                                                                                   | 48.3       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B79,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C79,SS_RhoF))  | =MAX(0,F79-E79*SS_PhiTsh)   | =IF(AND(G79>=SS_PhiCut,E79<=SS_VshCut),1,0)   | =IF(H79=1,PO.PP.Qv.FromCEC(E79*SS_CECsh,F79,SS_RhoMa),0)    | =IF(H79=1,E79*SS_PhiTsh/F79,0)    | =IF(H79=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G79,SS_Rw,D79)),1)    | =IF(H79=1,MIN(1,PO.PP.Sw.Simandoux(G79,D79,SS_Rw,E79,SS_Rsh)),1)     | =IF(H79=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G79,SS_Rw,D79,E79,SS_Rsh)),1)     | =IF(H79=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F79,SS_Rw,D79)),1)    | =IF(H79=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F79,SS_Rw,D79,SS_B,I79,SS_Mode)),1)     | =IF(H79=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F79,SS_Rw,SS_Rwb,J79,D79,SS_Mode),1,1)),1)     |
| 80  | 5030                                                                                                                                                                                                                               | 34                                                                                                        | 2.208                                                                                                                                                                                                                                                                                                                                   | 46.7       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B80,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C80,SS_RhoF))  | =MAX(0,F80-E80*SS_PhiTsh)   | =IF(AND(G80>=SS_PhiCut,E80<=SS_VshCut),1,0)   | =IF(H80=1,PO.PP.Qv.FromCEC(E80*SS_CECsh,F80,SS_RhoMa),0)    | =IF(H80=1,E80*SS_PhiTsh/F80,0)    | =IF(H80=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G80,SS_Rw,D80)),1)    | =IF(H80=1,MIN(1,PO.PP.Sw.Simandoux(G80,D80,SS_Rw,E80,SS_Rsh)),1)     | =IF(H80=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G80,SS_Rw,D80,E80,SS_Rsh)),1)     | =IF(H80=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F80,SS_Rw,D80)),1)    | =IF(H80=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F80,SS_Rw,D80,SS_B,I80,SS_Mode)),1)     | =IF(H80=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F80,SS_Rw,SS_Rwb,J80,D80,SS_Mode),1,1)),1)     |
| 81  | 5032                                                                                                                                                                                                                               | 37.5                                                                                                      | 2.234                                                                                                                                                                                                                                                                                                                                   | 37.3       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B81,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C81,SS_RhoF))  | =MAX(0,F81-E81*SS_PhiTsh)   | =IF(AND(G81>=SS_PhiCut,E81<=SS_VshCut),1,0)   | =IF(H81=1,PO.PP.Qv.FromCEC(E81*SS_CECsh,F81,SS_RhoMa),0)    | =IF(H81=1,E81*SS_PhiTsh/F81,0)    | =IF(H81=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G81,SS_Rw,D81)),1)    | =IF(H81=1,MIN(1,PO.PP.Sw.Simandoux(G81,D81,SS_Rw,E81,SS_Rsh)),1)     | =IF(H81=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G81,SS_Rw,D81,E81,SS_Rsh)),1)     | =IF(H81=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F81,SS_Rw,D81)),1)    | =IF(H81=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F81,SS_Rw,D81,SS_B,I81,SS_Mode)),1)     | =IF(H81=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F81,SS_Rw,SS_Rwb,J81,D81,SS_Mode),1,1)),1)     |
| 82  | 5034                                                                                                                                                                                                                               | 74.7                                                                                                      | 2.344                                                                                                                                                                                                                                                                                                                                   | 10.3       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B82,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C82,SS_RhoF))  | =MAX(0,F82-E82*SS_PhiTsh)   | =IF(AND(G82>=SS_PhiCut,E82<=SS_VshCut),1,0)   | =IF(H82=1,PO.PP.Qv.FromCEC(E82*SS_CECsh,F82,SS_RhoMa),0)    | =IF(H82=1,E82*SS_PhiTsh/F82,0)    | =IF(H82=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G82,SS_Rw,D82)),1)    | =IF(H82=1,MIN(1,PO.PP.Sw.Simandoux(G82,D82,SS_Rw,E82,SS_Rsh)),1)     | =IF(H82=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G82,SS_Rw,D82,E82,SS_Rsh)),1)     | =IF(H82=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F82,SS_Rw,D82)),1)    | =IF(H82=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F82,SS_Rw,D82,SS_B,I82,SS_Mode)),1)     | =IF(H82=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F82,SS_Rw,SS_Rwb,J82,D82,SS_Mode),1,1)),1)     |
| 83  | 5036                                                                                                                                                                                                                               | 108.7                                                                                                     | 2.463                                                                                                                                                                                                                                                                                                                                   | 3.25       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B83,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C83,SS_RhoF))  | =MAX(0,F83-E83*SS_PhiTsh)   | =IF(AND(G83>=SS_PhiCut,E83<=SS_VshCut),1,0)   | =IF(H83=1,PO.PP.Qv.FromCEC(E83*SS_CECsh,F83,SS_RhoMa),0)    | =IF(H83=1,E83*SS_PhiTsh/F83,0)    | =IF(H83=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G83,SS_Rw,D83)),1)    | =IF(H83=1,MIN(1,PO.PP.Sw.Simandoux(G83,D83,SS_Rw,E83,SS_Rsh)),1)     | =IF(H83=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G83,SS_Rw,D83,E83,SS_Rsh)),1)     | =IF(H83=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F83,SS_Rw,D83)),1)    | =IF(H83=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F83,SS_Rw,D83,SS_B,I83,SS_Mode)),1)     | =IF(H83=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F83,SS_Rw,SS_Rwb,J83,D83,SS_Mode),1,1)),1)     |
| 84  | 5038                                                                                                                                                                                                                               | 112.2                                                                                                     | 2.461                                                                                                                                                                                                                                                                                                                                   | 2.57       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B84,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C84,SS_RhoF))  | =MAX(0,F84-E84*SS_PhiTsh)   | =IF(AND(G84>=SS_PhiCut,E84<=SS_VshCut),1,0)   | =IF(H84=1,PO.PP.Qv.FromCEC(E84*SS_CECsh,F84,SS_RhoMa),0)    | =IF(H84=1,E84*SS_PhiTsh/F84,0)    | =IF(H84=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G84,SS_Rw,D84)),1)    | =IF(H84=1,MIN(1,PO.PP.Sw.Simandoux(G84,D84,SS_Rw,E84,SS_Rsh)),1)     | =IF(H84=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G84,SS_Rw,D84,E84,SS_Rsh)),1)     | =IF(H84=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F84,SS_Rw,D84)),1)    | =IF(H84=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F84,SS_Rw,D84,SS_B,I84,SS_Mode)),1)     | =IF(H84=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F84,SS_Rw,SS_Rwb,J84,D84,SS_Mode),1,1)),1)     |
| 85  | 5040                                                                                                                                                                                                                               | 85.4                                                                                                      | 2.41                                                                                                                                                                                                                                                                                                                                    | 6.84       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B85,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C85,SS_RhoF))  | =MAX(0,F85-E85*SS_PhiTsh)   | =IF(AND(G85>=SS_PhiCut,E85<=SS_VshCut),1,0)   | =IF(H85=1,PO.PP.Qv.FromCEC(E85*SS_CECsh,F85,SS_RhoMa),0)    | =IF(H85=1,E85*SS_PhiTsh/F85,0)    | =IF(H85=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G85,SS_Rw,D85)),1)    | =IF(H85=1,MIN(1,PO.PP.Sw.Simandoux(G85,D85,SS_Rw,E85,SS_Rsh)),1)     | =IF(H85=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G85,SS_Rw,D85,E85,SS_Rsh)),1)     | =IF(H85=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F85,SS_Rw,D85)),1)    | =IF(H85=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F85,SS_Rw,D85,SS_B,I85,SS_Mode)),1)     | =IF(H85=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F85,SS_Rw,SS_Rwb,J85,D85,SS_Mode),1,1)),1)     |
| 86  | 5042                                                                                                                                                                                                                               | 69.7                                                                                                      | 2.338                                                                                                                                                                                                                                                                                                                                   | 14.8       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B86,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C86,SS_RhoF))  | =MAX(0,F86-E86*SS_PhiTsh)   | =IF(AND(G86>=SS_PhiCut,E86<=SS_VshCut),1,0)   | =IF(H86=1,PO.PP.Qv.FromCEC(E86*SS_CECsh,F86,SS_RhoMa),0)    | =IF(H86=1,E86*SS_PhiTsh/F86,0)    | =IF(H86=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G86,SS_Rw,D86)),1)    | =IF(H86=1,MIN(1,PO.PP.Sw.Simandoux(G86,D86,SS_Rw,E86,SS_Rsh)),1)     | =IF(H86=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G86,SS_Rw,D86,E86,SS_Rsh)),1)     | =IF(H86=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F86,SS_Rw,D86)),1)    | =IF(H86=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F86,SS_Rw,D86,SS_B,I86,SS_Mode)),1)     | =IF(H86=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F86,SS_Rw,SS_Rwb,J86,D86,SS_Mode),1,1)),1)     |
| 87  | 5044                                                                                                                                                                                                                               | 59.9                                                                                                      | 2.33                                                                                                                                                                                                                                                                                                                                    | 18.3       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B87,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C87,SS_RhoF))  | =MAX(0,F87-E87*SS_PhiTsh)   | =IF(AND(G87>=SS_PhiCut,E87<=SS_VshCut),1,0)   | =IF(H87=1,PO.PP.Qv.FromCEC(E87*SS_CECsh,F87,SS_RhoMa),0)    | =IF(H87=1,E87*SS_PhiTsh/F87,0)    | =IF(H87=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G87,SS_Rw,D87)),1)    | =IF(H87=1,MIN(1,PO.PP.Sw.Simandoux(G87,D87,SS_Rw,E87,SS_Rsh)),1)     | =IF(H87=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G87,SS_Rw,D87,E87,SS_Rsh)),1)     | =IF(H87=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F87,SS_Rw,D87)),1)    | =IF(H87=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F87,SS_Rw,D87,SS_B,I87,SS_Mode)),1)     | =IF(H87=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F87,SS_Rw,SS_Rwb,J87,D87,SS_Mode),1,1)),1)     |
| 88  | 5046                                                                                                                                                                                                                               | 62.8                                                                                                      | 2.329                                                                                                                                                                                                                                                                                                                                   | 15.5       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B88,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C88,SS_RhoF))  | =MAX(0,F88-E88*SS_PhiTsh)   | =IF(AND(G88>=SS_PhiCut,E88<=SS_VshCut),1,0)   | =IF(H88=1,PO.PP.Qv.FromCEC(E88*SS_CECsh,F88,SS_RhoMa),0)    | =IF(H88=1,E88*SS_PhiTsh/F88,0)    | =IF(H88=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G88,SS_Rw,D88)),1)    | =IF(H88=1,MIN(1,PO.PP.Sw.Simandoux(G88,D88,SS_Rw,E88,SS_Rsh)),1)     | =IF(H88=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G88,SS_Rw,D88,E88,SS_Rsh)),1)     | =IF(H88=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F88,SS_Rw,D88)),1)    | =IF(H88=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F88,SS_Rw,D88,SS_B,I88,SS_Mode)),1)     | =IF(H88=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F88,SS_Rw,SS_Rwb,J88,D88,SS_Mode),1,1)),1)     |
| 89  | 5048                                                                                                                                                                                                                               | 60.8                                                                                                      | 2.333                                                                                                                                                                                                                                                                                                                                   | 10.3       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B89,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C89,SS_RhoF))  | =MAX(0,F89-E89*SS_PhiTsh)   | =IF(AND(G89>=SS_PhiCut,E89<=SS_VshCut),1,0)   | =IF(H89=1,PO.PP.Qv.FromCEC(E89*SS_CECsh,F89,SS_RhoMa),0)    | =IF(H89=1,E89*SS_PhiTsh/F89,0)    | =IF(H89=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G89,SS_Rw,D89)),1)    | =IF(H89=1,MIN(1,PO.PP.Sw.Simandoux(G89,D89,SS_Rw,E89,SS_Rsh)),1)     | =IF(H89=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G89,SS_Rw,D89,E89,SS_Rsh)),1)     | =IF(H89=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F89,SS_Rw,D89)),1)    | =IF(H89=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F89,SS_Rw,D89,SS_B,I89,SS_Mode)),1)     | =IF(H89=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F89,SS_Rw,SS_Rwb,J89,D89,SS_Mode),1,1)),1)     |
| 90  | 5050                                                                                                                                                                                                                               | 65.4                                                                                                      | 2.335                                                                                                                                                                                                                                                                                                                                   | 2.01       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B90,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C90,SS_RhoF))  | =MAX(0,F90-E90*SS_PhiTsh)   | =IF(AND(G90>=SS_PhiCut,E90<=SS_VshCut),1,0)   | =IF(H90=1,PO.PP.Qv.FromCEC(E90*SS_CECsh,F90,SS_RhoMa),0)    | =IF(H90=1,E90*SS_PhiTsh/F90,0)    | =IF(H90=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G90,SS_Rw,D90)),1)    | =IF(H90=1,MIN(1,PO.PP.Sw.Simandoux(G90,D90,SS_Rw,E90,SS_Rsh)),1)     | =IF(H90=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G90,SS_Rw,D90,E90,SS_Rsh)),1)     | =IF(H90=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F90,SS_Rw,D90)),1)    | =IF(H90=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F90,SS_Rw,D90,SS_B,I90,SS_Mode)),1)     | =IF(H90=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F90,SS_Rw,SS_Rwb,J90,D90,SS_Mode),1,1)),1)     |
| 91  | 5052                                                                                                                                                                                                                               | 61.1                                                                                                      | 2.336                                                                                                                                                                                                                                                                                                                                   | 1.15       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B91,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C91,SS_RhoF))  | =MAX(0,F91-E91*SS_PhiTsh)   | =IF(AND(G91>=SS_PhiCut,E91<=SS_VshCut),1,0)   | =IF(H91=1,PO.PP.Qv.FromCEC(E91*SS_CECsh,F91,SS_RhoMa),0)    | =IF(H91=1,E91*SS_PhiTsh/F91,0)    | =IF(H91=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G91,SS_Rw,D91)),1)    | =IF(H91=1,MIN(1,PO.PP.Sw.Simandoux(G91,D91,SS_Rw,E91,SS_Rsh)),1)     | =IF(H91=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G91,SS_Rw,D91,E91,SS_Rsh)),1)     | =IF(H91=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F91,SS_Rw,D91)),1)    | =IF(H91=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F91,SS_Rw,D91,SS_B,I91,SS_Mode)),1)     | =IF(H91=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F91,SS_Rw,SS_Rwb,J91,D91,SS_Mode),1,1)),1)     |
| 92  | 5054                                                                                                                                                                                                                               | 64.1                                                                                                      | 2.345                                                                                                                                                                                                                                                                                                                                   | 1.15       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B92,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C92,SS_RhoF))  | =MAX(0,F92-E92*SS_PhiTsh)   | =IF(AND(G92>=SS_PhiCut,E92<=SS_VshCut),1,0)   | =IF(H92=1,PO.PP.Qv.FromCEC(E92*SS_CECsh,F92,SS_RhoMa),0)    | =IF(H92=1,E92*SS_PhiTsh/F92,0)    | =IF(H92=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G92,SS_Rw,D92)),1)    | =IF(H92=1,MIN(1,PO.PP.Sw.Simandoux(G92,D92,SS_Rw,E92,SS_Rsh)),1)     | =IF(H92=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G92,SS_Rw,D92,E92,SS_Rsh)),1)     | =IF(H92=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F92,SS_Rw,D92)),1)    | =IF(H92=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F92,SS_Rw,D92,SS_B,I92,SS_Mode)),1)     | =IF(H92=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F92,SS_Rw,SS_Rwb,J92,D92,SS_Mode),1,1)),1)     |
| 93  | 5056                                                                                                                                                                                                                               | 68.7                                                                                                      | 2.345                                                                                                                                                                                                                                                                                                                                   | 1.18       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B93,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C93,SS_RhoF))  | =MAX(0,F93-E93*SS_PhiTsh)   | =IF(AND(G93>=SS_PhiCut,E93<=SS_VshCut),1,0)   | =IF(H93=1,PO.PP.Qv.FromCEC(E93*SS_CECsh,F93,SS_RhoMa),0)    | =IF(H93=1,E93*SS_PhiTsh/F93,0)    | =IF(H93=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G93,SS_Rw,D93)),1)    | =IF(H93=1,MIN(1,PO.PP.Sw.Simandoux(G93,D93,SS_Rw,E93,SS_Rsh)),1)     | =IF(H93=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G93,SS_Rw,D93,E93,SS_Rsh)),1)     | =IF(H93=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F93,SS_Rw,D93)),1)    | =IF(H93=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F93,SS_Rw,D93,SS_B,I93,SS_Mode)),1)     | =IF(H93=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F93,SS_Rw,SS_Rwb,J93,D93,SS_Mode),1,1)),1)     |
| 94  | 5058                                                                                                                                                                                                                               | 87.1                                                                                                      | 2.412                                                                                                                                                                                                                                                                                                                                   | 1.66       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B94,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C94,SS_RhoF))  | =MAX(0,F94-E94*SS_PhiTsh)   | =IF(AND(G94>=SS_PhiCut,E94<=SS_VshCut),1,0)   | =IF(H94=1,PO.PP.Qv.FromCEC(E94*SS_CECsh,F94,SS_RhoMa),0)    | =IF(H94=1,E94*SS_PhiTsh/F94,0)    | =IF(H94=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G94,SS_Rw,D94)),1)    | =IF(H94=1,MIN(1,PO.PP.Sw.Simandoux(G94,D94,SS_Rw,E94,SS_Rsh)),1)     | =IF(H94=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G94,SS_Rw,D94,E94,SS_Rsh)),1)     | =IF(H94=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F94,SS_Rw,D94)),1)    | =IF(H94=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F94,SS_Rw,D94,SS_B,I94,SS_Mode)),1)     | =IF(H94=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F94,SS_Rw,SS_Rwb,J94,D94,SS_Mode),1,1)),1)     |
| 95  | 5060                                                                                                                                                                                                                               | 111.4                                                                                                     | 2.467                                                                                                                                                                                                                                                                                                                                   | 2.19       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B95,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C95,SS_RhoF))  | =MAX(0,F95-E95*SS_PhiTsh)   | =IF(AND(G95>=SS_PhiCut,E95<=SS_VshCut),1,0)   | =IF(H95=1,PO.PP.Qv.FromCEC(E95*SS_CECsh,F95,SS_RhoMa),0)    | =IF(H95=1,E95*SS_PhiTsh/F95,0)    | =IF(H95=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G95,SS_Rw,D95)),1)    | =IF(H95=1,MIN(1,PO.PP.Sw.Simandoux(G95,D95,SS_Rw,E95,SS_Rsh)),1)     | =IF(H95=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G95,SS_Rw,D95,E95,SS_Rsh)),1)     | =IF(H95=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F95,SS_Rw,D95)),1)    | =IF(H95=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F95,SS_Rw,D95,SS_B,I95,SS_Mode)),1)     | =IF(H95=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F95,SS_Rw,SS_Rwb,J95,D95,SS_Mode),1,1)),1)     |
| 96  | 5062                                                                                                                                                                                                                               | 113.6                                                                                                     | 2.483                                                                                                                                                                                                                                                                                                                                   | 2.66       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B96,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C96,SS_RhoF))  | =MAX(0,F96-E96*SS_PhiTsh)   | =IF(AND(G96>=SS_PhiCut,E96<=SS_VshCut),1,0)   | =IF(H96=1,PO.PP.Qv.FromCEC(E96*SS_CECsh,F96,SS_RhoMa),0)    | =IF(H96=1,E96*SS_PhiTsh/F96,0)    | =IF(H96=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G96,SS_Rw,D96)),1)    | =IF(H96=1,MIN(1,PO.PP.Sw.Simandoux(G96,D96,SS_Rw,E96,SS_Rsh)),1)     | =IF(H96=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G96,SS_Rw,D96,E96,SS_Rsh)),1)     | =IF(H96=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F96,SS_Rw,D96)),1)    | =IF(H96=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F96,SS_Rw,D96,SS_B,I96,SS_Mode)),1)     | =IF(H96=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F96,SS_Rw,SS_Rwb,J96,D96,SS_Mode),1,1)),1)     |
| 97  | 5064                                                                                                                                                                                                                               | 116.6                                                                                                     | 2.474                                                                                                                                                                                                                                                                                                                                   | 2.24       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B97,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C97,SS_RhoF))  | =MAX(0,F97-E97*SS_PhiTsh)   | =IF(AND(G97>=SS_PhiCut,E97<=SS_VshCut),1,0)   | =IF(H97=1,PO.PP.Qv.FromCEC(E97*SS_CECsh,F97,SS_RhoMa),0)    | =IF(H97=1,E97*SS_PhiTsh/F97,0)    | =IF(H97=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G97,SS_Rw,D97)),1)    | =IF(H97=1,MIN(1,PO.PP.Sw.Simandoux(G97,D97,SS_Rw,E97,SS_Rsh)),1)     | =IF(H97=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G97,SS_Rw,D97,E97,SS_Rsh)),1)     | =IF(H97=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F97,SS_Rw,D97)),1)    | =IF(H97=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F97,SS_Rw,D97,SS_B,I97,SS_Mode)),1)     | =IF(H97=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F97,SS_Rw,SS_Rwb,J97,D97,SS_Mode),1,1)),1)     |
| 98  | 5066                                                                                                                                                                                                                               | 111.2                                                                                                     | 2.485                                                                                                                                                                                                                                                                                                                                   | 2.56       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B98,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C98,SS_RhoF))  | =MAX(0,F98-E98*SS_PhiTsh)   | =IF(AND(G98>=SS_PhiCut,E98<=SS_VshCut),1,0)   | =IF(H98=1,PO.PP.Qv.FromCEC(E98*SS_CECsh,F98,SS_RhoMa),0)    | =IF(H98=1,E98*SS_PhiTsh/F98,0)    | =IF(H98=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G98,SS_Rw,D98)),1)    | =IF(H98=1,MIN(1,PO.PP.Sw.Simandoux(G98,D98,SS_Rw,E98,SS_Rsh)),1)     | =IF(H98=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G98,SS_Rw,D98,E98,SS_Rsh)),1)     | =IF(H98=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F98,SS_Rw,D98)),1)    | =IF(H98=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F98,SS_Rw,D98,SS_B,I98,SS_Mode)),1)     | =IF(H98=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F98,SS_Rw,SS_Rwb,J98,D98,SS_Mode),1,1)),1)     |
| 99  | 5068                                                                                                                                                                                                                               | 117.9                                                                                                     | 2.48                                                                                                                                                                                                                                                                                                                                    | 2.45       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B99,SS_GRcl,SS_GRsh)))  | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C99,SS_RhoF))  | =MAX(0,F99-E99*SS_PhiTsh)   | =IF(AND(G99>=SS_PhiCut,E99<=SS_VshCut),1,0)   | =IF(H99=1,PO.PP.Qv.FromCEC(E99*SS_CECsh,F99,SS_RhoMa),0)    | =IF(H99=1,E99*SS_PhiTsh/F99,0)    | =IF(H99=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G99,SS_Rw,D99)),1)    | =IF(H99=1,MIN(1,PO.PP.Sw.Simandoux(G99,D99,SS_Rw,E99,SS_Rsh)),1)     | =IF(H99=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G99,SS_Rw,D99,E99,SS_Rsh)),1)     | =IF(H99=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F99,SS_Rw,D99)),1)    | =IF(H99=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F99,SS_Rw,D99,SS_B,I99,SS_Mode)),1)     | =IF(H99=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F99,SS_Rw,SS_Rwb,J99,D99,SS_Mode),1,1)),1)     |
| 100 | 5070                                                                                                                                                                                                                               | 106.2                                                                                                     | 2.488                                                                                                                                                                                                                                                                                                                                   | 3.74       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B100,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C100,SS_RhoF)) | =MAX(0,F100-E100*SS_PhiTsh) | =IF(AND(G100>=SS_PhiCut,E100<=SS_VshCut),1,0) | =IF(H100=1,PO.PP.Qv.FromCEC(E100*SS_CECsh,F100,SS_RhoMa),0) | =IF(H100=1,E100*SS_PhiTsh/F100,0) | =IF(H100=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G100,SS_Rw,D100)),1) | =IF(H100=1,MIN(1,PO.PP.Sw.Simandoux(G100,D100,SS_Rw,E100,SS_Rsh)),1) | =IF(H100=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G100,SS_Rw,D100,E100,SS_Rsh)),1) | =IF(H100=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F100,SS_Rw,D100)),1) | =IF(H100=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F100,SS_Rw,D100,SS_B,I100,SS_Mode)),1) | =IF(H100=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F100,SS_Rw,SS_Rwb,J100,D100,SS_Mode),1,1)),1) |
| 101 | 5072                                                                                                                                                                                                                               | 69.6                                                                                                      | 2.53                                                                                                                                                                                                                                                                                                                                    | 29.3       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B101,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C101,SS_RhoF)) | =MAX(0,F101-E101*SS_PhiTsh) | =IF(AND(G101>=SS_PhiCut,E101<=SS_VshCut),1,0) | =IF(H101=1,PO.PP.Qv.FromCEC(E101*SS_CECsh,F101,SS_RhoMa),0) | =IF(H101=1,E101*SS_PhiTsh/F101,0) | =IF(H101=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G101,SS_Rw,D101)),1) | =IF(H101=1,MIN(1,PO.PP.Sw.Simandoux(G101,D101,SS_Rw,E101,SS_Rsh)),1) | =IF(H101=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G101,SS_Rw,D101,E101,SS_Rsh)),1) | =IF(H101=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F101,SS_Rw,D101)),1) | =IF(H101=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F101,SS_Rw,D101,SS_B,I101,SS_Mode)),1) | =IF(H101=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F101,SS_Rw,SS_Rwb,J101,D101,SS_Mode),1,1)),1) |
| 102 | 5074                                                                                                                                                                                                                               | 28.7                                                                                                      | 2.567                                                                                                                                                                                                                                                                                                                                   | 259        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B102,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C102,SS_RhoF)) | =MAX(0,F102-E102*SS_PhiTsh) | =IF(AND(G102>=SS_PhiCut,E102<=SS_VshCut),1,0) | =IF(H102=1,PO.PP.Qv.FromCEC(E102*SS_CECsh,F102,SS_RhoMa),0) | =IF(H102=1,E102*SS_PhiTsh/F102,0) | =IF(H102=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G102,SS_Rw,D102)),1) | =IF(H102=1,MIN(1,PO.PP.Sw.Simandoux(G102,D102,SS_Rw,E102,SS_Rsh)),1) | =IF(H102=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G102,SS_Rw,D102,E102,SS_Rsh)),1) | =IF(H102=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F102,SS_Rw,D102)),1) | =IF(H102=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F102,SS_Rw,D102,SS_B,I102,SS_Mode)),1) | =IF(H102=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F102,SS_Rw,SS_Rwb,J102,D102,SS_Mode),1,1)),1) |
| 103 | 5076                                                                                                                                                                                                                               | 28.4                                                                                                      | 2.502                                                                                                                                                                                                                                                                                                                                   | 98.6       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B103,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C103,SS_RhoF)) | =MAX(0,F103-E103*SS_PhiTsh) | =IF(AND(G103>=SS_PhiCut,E103<=SS_VshCut),1,0) | =IF(H103=1,PO.PP.Qv.FromCEC(E103*SS_CECsh,F103,SS_RhoMa),0) | =IF(H103=1,E103*SS_PhiTsh/F103,0) | =IF(H103=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G103,SS_Rw,D103)),1) | =IF(H103=1,MIN(1,PO.PP.Sw.Simandoux(G103,D103,SS_Rw,E103,SS_Rsh)),1) | =IF(H103=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G103,SS_Rw,D103,E103,SS_Rsh)),1) | =IF(H103=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F103,SS_Rw,D103)),1) | =IF(H103=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F103,SS_Rw,D103,SS_B,I103,SS_Mode)),1) | =IF(H103=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F103,SS_Rw,SS_Rwb,J103,D103,SS_Mode),1,1)),1) |
| 104 | 5078                                                                                                                                                                                                                               | 31.9                                                                                                      | 2.306                                                                                                                                                                                                                                                                                                                                   | 2.92       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B104,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C104,SS_RhoF)) | =MAX(0,F104-E104*SS_PhiTsh) | =IF(AND(G104>=SS_PhiCut,E104<=SS_VshCut),1,0) | =IF(H104=1,PO.PP.Qv.FromCEC(E104*SS_CECsh,F104,SS_RhoMa),0) | =IF(H104=1,E104*SS_PhiTsh/F104,0) | =IF(H104=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G104,SS_Rw,D104)),1) | =IF(H104=1,MIN(1,PO.PP.Sw.Simandoux(G104,D104,SS_Rw,E104,SS_Rsh)),1) | =IF(H104=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G104,SS_Rw,D104,E104,SS_Rsh)),1) | =IF(H104=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F104,SS_Rw,D104)),1) | =IF(H104=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F104,SS_Rw,D104,SS_B,I104,SS_Mode)),1) | =IF(H104=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F104,SS_Rw,SS_Rwb,J104,D104,SS_Mode),1,1)),1) |
| 105 | 5080                                                                                                                                                                                                                               | 36                                                                                                        | 2.245                                                                                                                                                                                                                                                                                                                                   | 0.885      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B105,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C105,SS_RhoF)) | =MAX(0,F105-E105*SS_PhiTsh) | =IF(AND(G105>=SS_PhiCut,E105<=SS_VshCut),1,0) | =IF(H105=1,PO.PP.Qv.FromCEC(E105*SS_CECsh,F105,SS_RhoMa),0) | =IF(H105=1,E105*SS_PhiTsh/F105,0) | =IF(H105=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G105,SS_Rw,D105)),1) | =IF(H105=1,MIN(1,PO.PP.Sw.Simandoux(G105,D105,SS_Rw,E105,SS_Rsh)),1) | =IF(H105=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G105,SS_Rw,D105,E105,SS_Rsh)),1) | =IF(H105=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F105,SS_Rw,D105)),1) | =IF(H105=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F105,SS_Rw,D105,SS_B,I105,SS_Mode)),1) | =IF(H105=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F105,SS_Rw,SS_Rwb,J105,D105,SS_Mode),1,1)),1) |
| 106 | 5082                                                                                                                                                                                                                               | 38.7                                                                                                      | 2.227                                                                                                                                                                                                                                                                                                                                   | 0.742      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B106,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C106,SS_RhoF)) | =MAX(0,F106-E106*SS_PhiTsh) | =IF(AND(G106>=SS_PhiCut,E106<=SS_VshCut),1,0) | =IF(H106=1,PO.PP.Qv.FromCEC(E106*SS_CECsh,F106,SS_RhoMa),0) | =IF(H106=1,E106*SS_PhiTsh/F106,0) | =IF(H106=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G106,SS_Rw,D106)),1) | =IF(H106=1,MIN(1,PO.PP.Sw.Simandoux(G106,D106,SS_Rw,E106,SS_Rsh)),1) | =IF(H106=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G106,SS_Rw,D106,E106,SS_Rsh)),1) | =IF(H106=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F106,SS_Rw,D106)),1) | =IF(H106=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F106,SS_Rw,D106,SS_B,I106,SS_Mode)),1) | =IF(H106=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F106,SS_Rw,SS_Rwb,J106,D106,SS_Mode),1,1)),1) |
| 107 | 5084                                                                                                                                                                                                                               | 34.6                                                                                                      | 2.233                                                                                                                                                                                                                                                                                                                                   | 0.751      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B107,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C107,SS_RhoF)) | =MAX(0,F107-E107*SS_PhiTsh) | =IF(AND(G107>=SS_PhiCut,E107<=SS_VshCut),1,0) | =IF(H107=1,PO.PP.Qv.FromCEC(E107*SS_CECsh,F107,SS_RhoMa),0) | =IF(H107=1,E107*SS_PhiTsh/F107,0) | =IF(H107=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G107,SS_Rw,D107)),1) | =IF(H107=1,MIN(1,PO.PP.Sw.Simandoux(G107,D107,SS_Rw,E107,SS_Rsh)),1) | =IF(H107=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G107,SS_Rw,D107,E107,SS_Rsh)),1) | =IF(H107=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F107,SS_Rw,D107)),1) | =IF(H107=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F107,SS_Rw,D107,SS_B,I107,SS_Mode)),1) | =IF(H107=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F107,SS_Rw,SS_Rwb,J107,D107,SS_Mode),1,1)),1) |
| 108 | 5086                                                                                                                                                                                                                               | 37.5                                                                                                      | 2.228                                                                                                                                                                                                                                                                                                                                   | 0.693      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B108,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C108,SS_RhoF)) | =MAX(0,F108-E108*SS_PhiTsh) | =IF(AND(G108>=SS_PhiCut,E108<=SS_VshCut),1,0) | =IF(H108=1,PO.PP.Qv.FromCEC(E108*SS_CECsh,F108,SS_RhoMa),0) | =IF(H108=1,E108*SS_PhiTsh/F108,0) | =IF(H108=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G108,SS_Rw,D108)),1) | =IF(H108=1,MIN(1,PO.PP.Sw.Simandoux(G108,D108,SS_Rw,E108,SS_Rsh)),1) | =IF(H108=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G108,SS_Rw,D108,E108,SS_Rsh)),1) | =IF(H108=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F108,SS_Rw,D108)),1) | =IF(H108=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F108,SS_Rw,D108,SS_B,I108,SS_Mode)),1) | =IF(H108=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F108,SS_Rw,SS_Rwb,J108,D108,SS_Mode),1,1)),1) |
| 109 | 5088                                                                                                                                                                                                                               | 35.5                                                                                                      | 2.235                                                                                                                                                                                                                                                                                                                                   | 0.812      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B109,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C109,SS_RhoF)) | =MAX(0,F109-E109*SS_PhiTsh) | =IF(AND(G109>=SS_PhiCut,E109<=SS_VshCut),1,0) | =IF(H109=1,PO.PP.Qv.FromCEC(E109*SS_CECsh,F109,SS_RhoMa),0) | =IF(H109=1,E109*SS_PhiTsh/F109,0) | =IF(H109=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G109,SS_Rw,D109)),1) | =IF(H109=1,MIN(1,PO.PP.Sw.Simandoux(G109,D109,SS_Rw,E109,SS_Rsh)),1) | =IF(H109=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G109,SS_Rw,D109,E109,SS_Rsh)),1) | =IF(H109=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F109,SS_Rw,D109)),1) | =IF(H109=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F109,SS_Rw,D109,SS_B,I109,SS_Mode)),1) | =IF(H109=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F109,SS_Rw,SS_Rwb,J109,D109,SS_Mode),1,1)),1) |
| 110 | 5090                                                                                                                                                                                                                               | 38.7                                                                                                      | 2.224                                                                                                                                                                                                                                                                                                                                   | 0.681      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B110,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C110,SS_RhoF)) | =MAX(0,F110-E110*SS_PhiTsh) | =IF(AND(G110>=SS_PhiCut,E110<=SS_VshCut),1,0) | =IF(H110=1,PO.PP.Qv.FromCEC(E110*SS_CECsh,F110,SS_RhoMa),0) | =IF(H110=1,E110*SS_PhiTsh/F110,0) | =IF(H110=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G110,SS_Rw,D110)),1) | =IF(H110=1,MIN(1,PO.PP.Sw.Simandoux(G110,D110,SS_Rw,E110,SS_Rsh)),1) | =IF(H110=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G110,SS_Rw,D110,E110,SS_Rsh)),1) | =IF(H110=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F110,SS_Rw,D110)),1) | =IF(H110=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F110,SS_Rw,D110,SS_B,I110,SS_Mode)),1) | =IF(H110=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F110,SS_Rw,SS_Rwb,J110,D110,SS_Mode),1,1)),1) |
| 111 | 5092                                                                                                                                                                                                                               | 32.3                                                                                                      | 2.233                                                                                                                                                                                                                                                                                                                                   | 0.769      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B111,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C111,SS_RhoF)) | =MAX(0,F111-E111*SS_PhiTsh) | =IF(AND(G111>=SS_PhiCut,E111<=SS_VshCut),1,0) | =IF(H111=1,PO.PP.Qv.FromCEC(E111*SS_CECsh,F111,SS_RhoMa),0) | =IF(H111=1,E111*SS_PhiTsh/F111,0) | =IF(H111=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G111,SS_Rw,D111)),1) | =IF(H111=1,MIN(1,PO.PP.Sw.Simandoux(G111,D111,SS_Rw,E111,SS_Rsh)),1) | =IF(H111=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G111,SS_Rw,D111,E111,SS_Rsh)),1) | =IF(H111=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F111,SS_Rw,D111)),1) | =IF(H111=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F111,SS_Rw,D111,SS_B,I111,SS_Mode)),1) | =IF(H111=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F111,SS_Rw,SS_Rwb,J111,D111,SS_Mode),1,1)),1) |
| 112 | 5094                                                                                                                                                                                                                               | 39.2                                                                                                      | 2.229                                                                                                                                                                                                                                                                                                                                   | 0.727      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B112,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C112,SS_RhoF)) | =MAX(0,F112-E112*SS_PhiTsh) | =IF(AND(G112>=SS_PhiCut,E112<=SS_VshCut),1,0) | =IF(H112=1,PO.PP.Qv.FromCEC(E112*SS_CECsh,F112,SS_RhoMa),0) | =IF(H112=1,E112*SS_PhiTsh/F112,0) | =IF(H112=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G112,SS_Rw,D112)),1) | =IF(H112=1,MIN(1,PO.PP.Sw.Simandoux(G112,D112,SS_Rw,E112,SS_Rsh)),1) | =IF(H112=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G112,SS_Rw,D112,E112,SS_Rsh)),1) | =IF(H112=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F112,SS_Rw,D112)),1) | =IF(H112=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F112,SS_Rw,D112,SS_B,I112,SS_Mode)),1) | =IF(H112=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F112,SS_Rw,SS_Rwb,J112,D112,SS_Mode),1,1)),1) |
| 113 | 5096                                                                                                                                                                                                                               | 34.9                                                                                                      | 2.229                                                                                                                                                                                                                                                                                                                                   | 0.784      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B113,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C113,SS_RhoF)) | =MAX(0,F113-E113*SS_PhiTsh) | =IF(AND(G113>=SS_PhiCut,E113<=SS_VshCut),1,0) | =IF(H113=1,PO.PP.Qv.FromCEC(E113*SS_CECsh,F113,SS_RhoMa),0) | =IF(H113=1,E113*SS_PhiTsh/F113,0) | =IF(H113=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G113,SS_Rw,D113)),1) | =IF(H113=1,MIN(1,PO.PP.Sw.Simandoux(G113,D113,SS_Rw,E113,SS_Rsh)),1) | =IF(H113=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G113,SS_Rw,D113,E113,SS_Rsh)),1) | =IF(H113=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F113,SS_Rw,D113)),1) | =IF(H113=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F113,SS_Rw,D113,SS_B,I113,SS_Mode)),1) | =IF(H113=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F113,SS_Rw,SS_Rwb,J113,D113,SS_Mode),1,1)),1) |
| 114 | 5098                                                                                                                                                                                                                               | 42                                                                                                        | 2.248                                                                                                                                                                                                                                                                                                                                   | 0.767      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B114,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C114,SS_RhoF)) | =MAX(0,F114-E114*SS_PhiTsh) | =IF(AND(G114>=SS_PhiCut,E114<=SS_VshCut),1,0) | =IF(H114=1,PO.PP.Qv.FromCEC(E114*SS_CECsh,F114,SS_RhoMa),0) | =IF(H114=1,E114*SS_PhiTsh/F114,0) | =IF(H114=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G114,SS_Rw,D114)),1) | =IF(H114=1,MIN(1,PO.PP.Sw.Simandoux(G114,D114,SS_Rw,E114,SS_Rsh)),1) | =IF(H114=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G114,SS_Rw,D114,E114,SS_Rsh)),1) | =IF(H114=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F114,SS_Rw,D114)),1) | =IF(H114=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F114,SS_Rw,D114,SS_B,I114,SS_Mode)),1) | =IF(H114=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F114,SS_Rw,SS_Rwb,J114,D114,SS_Mode),1,1)),1) |
| 115 | 5100                                                                                                                                                                                                                               | 74                                                                                                        | 2.355                                                                                                                                                                                                                                                                                                                                   | 1.39       | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B115,SS_GRcl,SS_GRsh))) | =MAX(0,PO.PP.Porosity.FromDensity(SS_RhoMa,C115,SS_RhoF)) | =MAX(0,F115-E115*SS_PhiTsh) | =IF(AND(G115>=SS_PhiCut,E115<=SS_VshCut),1,0) | =IF(H115=1,PO.PP.Qv.FromCEC(E115*SS_CECsh,F115,SS_RhoMa),0) | =IF(H115=1,E115*SS_PhiTsh/F115,0) | =IF(H115=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,G115,SS_Rw,D115)),1) | =IF(H115=1,MIN(1,PO.PP.Sw.Simandoux(G115,D115,SS_Rw,E115,SS_Rsh)),1) | =IF(H115=1,MIN(1,PO.PP.Sw.Indonesia(SS_a,SS_m,SS_n,G115,SS_Rw,D115,E115,SS_Rsh)),1) | =IF(H115=1,MIN(1,PO.PP.Sw.Archie(SS_a,SS_m,SS_n,F115,SS_Rw,D115)),1) | =IF(H115=1,MIN(1,PO.PP.Sw.WaxmanSmits(SS_a,SS_m,SS_n,F115,SS_Rw,D115,SS_B,I115,SS_Mode)),1) | =IF(H115=1,MIN(1,INDEX(PO.PP.Sw.DualWater(SS_a,SS_m,SS_n,F115,SS_Rw,SS_Rwb,J115,D115,SS_Mode),1,1)),1) |

## Lambdas

| Name | RefersTo | Comment |
|------|----------|---------|
| PO.PP.Vsh.GammaRayIndex | =LAMBDA(GR, GR_cl, GR_sh, (GR-GR_cl)/(GR_sh-GR_cl)) | Linear gamma-ray shale index, IGR = (GR - GRclean) / (GRshale - GRclean). |
| PO.PP.Porosity.FromDensity | =LAMBDA(Rho_ma, Rho_b, Rho_f, (Rho_ma-Rho_b)/(Rho_ma-Rho_f)) | Porosity from a density log, (matrix density - bulk density) / (matrix density - fluid density). |
| PO.PP.Sw.Archie | =LAMBDA(a, m, n, Phi, Rw, Rt, ((a/Phi^m)*(Rw/Rt))^(1/n)) | Water saturation from the general Archie equation, Sw = ((a/phi^m)*(Rw/Rt))^(1/n). |
| PO.PP.Sw.Simandoux | =LAMBDA(Phi_e, Rt, Rw, Vsh, Rsh, (0.4*Rw/Phi_e^2)*(-Vsh/Rsh+SQRT((Vsh/Rsh)^2+5*Phi_e^2/(Rw*Rt)))) | Simandoux (1963) water saturation for a shaly sand, Bassiouni's a = 0.8 and m = 2 form. |
| PO.PP.Sw.Indonesia | =LAMBDA(a, m, n, Phi_e, Rw, Rt, Vsh, Rsh, POWER(1/(SQRT(Rt)*(Vsh^(1-Vsh/2)/SQRT(Rsh)+Phi_e^(m/2)/SQRT(a*Rw))), 2/n)) | Indonesia (Poupon-Leveaux 1971) water saturation for a shaly formation. |
| PO.PP.Qv.FromCEC | =LAMBDA(CEC, PhiT_frac, Rho_g, CEC*(1-PhiT_frac)*Rho_g/(100*PhiT_frac)) | Cation exchange capacity per unit pore volume, Qv = CEC (1 - phi) rho_g / (100 phi), meq/cm3, from CEC in meq/100 g. |
| PO.PP.Sw.WaxmanSmits | =LAMBDA(a, m, n, Phi, Rw, Rt, B, Qv, Mode, LET(ct, 1/Rt, cw, 1/Rw, kf, Phi^m/a, bq, B*Qv, IF(Mode=1, IF(n=2, (-bq+SQRT(bq^2+4*cw*ct/kf))/(2*cw), NA()), IF(Mode=2, REDUCE(1, SEQUENCE(30), LAMBDA(s, j, s-(kf*(cw*s^n+bq*s^(n-1))-ct)/(kf*(n*cw*s^(n-1)+(n-1)*bq*s^(n-2))))), NA())))) | Waxman-Smits (1968) water saturation from Qv and B: Mode 1 the quadratic closed form (n = 2 only), Mode 2 a 30-step Newton solve for any n. |
| PO.PP.Sw.DualWater | =LAMBDA(a, m, n, Phi_t, Rw, Rwb, Swb, Rt, Mode, LET(ct, 1/Rt, cw, 1/Rw, kf, Phi_t^m/a, bq, (1/Rwb-1/Rw)*Swb, swt, IF(Mode=1, IF(n=2, (-bq+SQRT(bq^2+4*cw*ct/kf))/(2*cw), NA()), IF(Mode=2, REDUCE(1, SEQUENCE(30), LAMBDA(s, j, s-(kf*(cw*s^n+bq*s^(n-1))-ct)/(kf*(n*cw*s^(n-1)+(n-1)*bq*s^(n-2))))), NA())), HSTACK(swt, (swt-Swb)/(1-Swb)))) | Dual-water (Clavier et al. 1984) saturation: {Swt, Swe}. Mode 1 the quadratic closed form (n = 2 only), Mode 2 a 30-step Newton solve for any n. |

## Names

| Name | RefersTo | Comment |
|------|----------|---------|
| SS_a | $B$4 | Tortuosity factor a |
| SS_m | $B$5 | Cementation exponent m (m* for Waxman-Smits) |
| SS_n | $B$6 | Saturation exponent n (n* for Waxman-Smits) |
| SS_Rw | $B$7 | Formation-water resistivity at formation temperature, ohm·m |
| SS_Rsh | $B$8 | Shale resistivity, read in a thick shale, ohm·m |
| SS_GRcl | $B$9 | Clean-sand gamma ray (Vsh = 0), API |
| SS_GRsh | $B$10 | Shale gamma ray (Vsh = 1), API |
| SS_RhoMa | $B$11 | Matrix and grain density (sandstone), g/cm³ |
| SS_RhoF | $B$12 | Fluid density (fresh mud filtrate), g/cm³ |
| SS_RhoSh | $B$13 | Shale bulk density, g/cm³ |
| SS_CECsh | $B$14 | Shale cation exchange capacity (core), scaled by Vsh in the sand, meq/100 g |
| SS_Tf | $B$15 | Formation temperature, °F |
| SS_ZTop | $B$16 | Zone top (the shaly oil sand, a foot inside), ft |
| SS_ZBase | $B$17 | Zone base (a foot inside the bed's base), ft |
| SS_VshCut | $B$18 | Shale-volume cutoff for reservoir, v/v |
| SS_PhiCut | $B$19 | Effective-porosity cutoff for reservoir, % |
| SS_Tol | $B$20 | Agreement limit between models, on hydrocarbon volume, % |
| SS_Inputs | $B$4:$B$20 | Archie's a, m and n, Rw, Rsh, the gamma-ray picks, the matrix, fluid and shale densities, the shale's CEC, the formation temperature, the zone, the reservoir cutoffs and the agreement limit |
| SS_PhiTsh | $B$24 | Shale total porosity (density), % |
| SS_Rwb | $B$25 | Bound-water resistivity Rwb = Rsh φtsh^m / a, ohm·m |
| SS_TfC | $B$26 | Formation temperature, °C |
| SS_B | $B$27 | Waxman-Smits B at formation temperature and Rw (Juhasz), (S/m)/(meq/cm³) |
| SS_Mode | $B$28 | Solve: 1 closed form (n = 2), 2 Newton |
| SS_ZVsh | $B$29 | Zone mean shale volume (reservoir samples), v/v |
| SS_ZPhiT | $B$30 | Zone mean total porosity, % |
| SS_ZPhiE | $B$31 | Zone mean effective porosity, % |
| SS_ZQv | $B$32 | Zone mean Qv, meq/cm³ |
| SS_ZSwb | $B$33 | Zone mean bound-water saturation, % |
| SS_Step | $B$34 | Log sample spacing, ft |
| SS_Bound | $B$35 | Clay-bound water thickness over the log, Σ φt Swb, ft |
| SS_ZSwA | $B$36 | Zone Sw, Archie (φe), % |
| SS_ZSwS | $B$37 | Zone Sw, Simandoux (φe), % |
| SS_ZSwI | $B$38 | Zone Sw, Indonesia (φe), % |
| SS_ZSwT | $B$39 | Zone Sw, Archie (φt), % |
| SS_ZSwW | $B$40 | Zone Sw, Waxman-Smits (φt), % |
| SS_ZSwD | $B$41 | Zone Sw, Dual water (φt), % |
| SS_ZHcA | $B$42 | Zone hydrocarbon volume, Archie on effective porosity, v/v |
| SS_ZHcShaly | $B$43 | Zone hydrocarbon volume, the four shaly-sand models' mean, v/v |
| SS_Short | $B$44 | Archie's shortfall in the zone against that mean, % |
| SS_HcA | $B$45 | Hydrocarbon pore thickness over the log, Archie (φe), ft |
| SS_HcS | $B$46 | Hydrocarbon pore thickness over the log, Simandoux (φe), ft |
| SS_HcI | $B$47 | Hydrocarbon pore thickness over the log, Indonesia (φe), ft |
| SS_HcT | $B$48 | Hydrocarbon pore thickness over the log, Archie (φt), ft |
| SS_HcW | $B$49 | Hydrocarbon pore thickness over the log, Waxman-Smits (φt), ft |
| SS_HcD | $B$50 | Hydrocarbon pore thickness over the log, Dual water (φt), ft |
| SS_Spread | $B$51 | Spread of the four shaly-sand models over the log, % |
| SS_ArchieCheck | $B$52 | Archie in the zone check verdict |
| SS_ArchieCheckNote | $C$52 | Archie in the zone check comment |
| SS_SpreadCheck | $B$53 | Model agreement check verdict |
| SS_SpreadCheckNote | $C$53 | Model agreement check comment |
| SS_Results | $B$24:$B$53 | Shale porosity, Rwb, temperature, B and the solve, the zone's shale volume, porosities, Qv, bound water and Sw by each model, hydrocarbon by Archie and the shaly-sand models, clay-bound water, HC pore thickness by model, their spread, two checks |
| SS_TfZero | $B$59 | Water's freezing point, °F |
| SS_TfPerC | $B$60 | Fahrenheit degrees per Celsius degree, °F/°C |
| SS_J1 | $B$61 | Juhasz B, constant term |
| SS_J2 | $B$62 | Juhasz B, temperature term, 1/°C |
| SS_J3 | $B$63 | Juhasz B, temperature-squared term, 1/°C² |
| SS_J4 | $B$64 | Juhasz B, exponent of Rw |
| SS_J5 | $B$65 | Juhasz B, Rw term's temperature slope, 1/°C |
| SS_J6 | $B$66 | Juhasz B, Rw term's constant |
| SS_Curve | $A$70:$P$115 | Each depth's GR, density and deep resistivity, its shale volume, total and effective porosity, reservoir flag, Qv, bound-water saturation and Sw by each of the six models |

---

## Related Blueprints
- [Net Pay and Cutoffs over an Interval](/blueprint/po.pp.netpay.cutoffs.md)
- [Saturation-Height Function by Leverett J](/blueprint/po.pp.shf.fit.md)
- [Archie Water Saturation and Bulk Volume Water](/blueprint/po.pp.sw.archie.md)
- [Permeability from Logs](/blueprint/po.pp.permeability.estimate.md)
- [Shale Volume from Gamma Ray](/blueprint/po.pp.vshale.gr.md)
- [Formation Water Resistivity](/blueprint/po.pp.rw.determination.md)

