---
cid: po.bp.pp.netpay.cutoffs
hub: pp
tags: [petrophysics, net-pay, net-reservoir, cutoffs, net-to-gross, shale-volume, porosity, water-saturation, core, permeability-cutoff, sensitivity, hydrocarbon-pore-thickness, quick-look]
facets: { discipline: reservoir, property: thickness, method-type: empirical }
title: Net Pay and Cutoffs over an Interval
summary: "How much of an interval is net reservoir and net pay by shale-volume, porosity and Sw cutoffs, and how much the answer depends on the cutoffs."
slug: po.pp.netpay.cutoffs
type: worksheet
---

# Net Pay and Cutoffs over an Interval

## Description

How much of the interval is reservoir, how much of it is pay, and how much does that depend on where the cutoffs sit? You enter a log of gamma ray, bulk density and deep resistivity, the picks and Archie's parameters, the gross interval, the Vsh, porosity and Sw cutoffs, and core plugs with a permeability cutoff. You read off the net reservoir, the net pay, the net-to-gross, the pay's mean porosity and Sw, its hydrocarbon pore thickness, the porosity cutoff core supports, and net pay over a range of cutoffs.

**Parameters:**
- **Picks and rock**: the clean and shale gamma ray `NP_GRcl`, `NP_GRsh` (API), the matrix, fluid and shale densities `NP_RhoMa`, `NP_RhoF`, `NP_RhoSh` (g/cm³)
- **Archie**: `NP_a`, `NP_m`, `NP_n` and `NP_Rw` (ohm·m at formation temperature)
- **Gross interval**: its top `NP_Top` and base `NP_Base` (ft)
- **Cutoffs**: `NP_VshCut` (v/v), `NP_PhiCut` and `NP_SwCut`, and the core permeability cutoff `NP_KCut` (mD)
- **Limits**: the agreement with core `NP_CutTol` (porosity) and the largest net-pay change `NP_SensMax`
- **Log and core**: each depth's GR, bulk density and deep resistivity in the log table, and each plug's depth, porosity and permeability in the core table

**How to use it:** The log and the core are synthetic. Paste your depth, GR, bulk density and deep resistivity over the log table, and your routine-core porosity and permeability over the core table. Set the cutoffs from core and flow tests, and the permeability cutoff from the lowest permeability that has flowed in this field. Where a shaly-sand model reads the shaly beds better than Archie, compute Sw with it and paste the Sw column in. Read the core check before trusting the porosity cutoff, and the sensitivity check before quoting net pay to the foot: when a 2 p.u. step in the porosity cutoff moves net pay by more than the limit, much rock sits near the cutoff.

**Method:**

- **Curves.** At every log sample the sheet works out three curves: the shale volume from the linear gamma-ray index, the density porosity corrected for shale, and Archie's water saturation on it. Vsh is the gamma-ray index (GR − GRcl)/(GRsh − GRcl), kept between 0 and 1. The effective porosity is the density porosity (ρma − ρb)/(ρma − ρf) less Vsh times the shale's density porosity, at least 0. Sw is Archie's (a Rw / (φ^m Rt))^(1/n) on it, at most 1.
- **Sums.** Each sample stands for the log spacing h inside the gross interval and for nothing outside it. A sample is reservoir when Vsh ≤ the Vsh cutoff and φ ≥ the porosity cutoff, and pay when also Sw ≤ the Sw cutoff. The net-pay function sums the gross Σ h, the net reservoir Σ h over reservoir, and the net pay Σ h over pay. The net-to-gross is the net reservoir over the gross. The pay's porosity is Σ h φ / Σ h over pay, and its Sw is Σ h φ Sw / Σ h φ over pay. The sheet adds the hydrocarbon pore thickness, net pay × φ × (1 − Sw).
- **Porosity cutoff from core.** log10 k = A + B φ is fitted by least squares over the plugs, and the porosity cutoff is the porosity at the permeability cutoff, (log10 kcut − A)/B.
- **Sensitivity.** A table works out net pay over porosity cutoffs from 4 p.u. below to 6 p.u. above the input, at Sw cutoffs 0.2 either side of its input, and the chart draws it. The sensitivity is the net pay at the porosity cutoff 2 p.u. below less that at 2 p.u. above, halved and over the net pay.
- **Checks.** The pay check fails when no sample passes all three cutoffs. The core cutoff check warns when core's porosity cutoff differs from the one used by more than the limit, and gives the net pay at core's. The sensitivity check warns when the sensitivity is above the limit.

**Example:** The default case is the Well-Log Display workbook's synthetic interval, 5,000 to 5,120 ft, every 2 ft, with its picks of 30 and 115 API, Rw of 0.05 ohm·m and cutoffs of 0.40 Vsh, 10% porosity and 60% Sw. The gross interval runs from the oil sand's top at 5,012 ft to the water sand's base at 5,100 ft. Archie's a, m and n are 1, 2 and 2, and the shale's 2.48 g/cm³ makes the shale correction. The core is the interval's fifteen synthetic plugs, and the permeability cutoff is 1 mD.

The gross interval holds 44 samples, 88 ft. The shale's density porosity is (2.65 − 2.48)/1.65 = 10.3%. Over the gross the thickness-weighted Vsh is 0.341, the porosity 16.1% and the Sw 68.3%. Twenty-five samples, 50 ft, pass the Vsh and porosity cutoffs: a net-to-gross of 56.8%. The oil sand's ten and the shaly sand's three oil-bearing samples also pass the Sw cutoff, so the net pay is 26 ft, 29.5% of the gross. Its mean porosity is 23.5% and its Sw 16.7%, a hydrocarbon pore thickness of 26 × 0.2349 × 0.8333 = 5.09 ft. Core puts 1 mD at 10.4% porosity, within 1 p.u. of the 10% cutoff, and net pay at core's cutoff is the same 26 ft. A 2 p.u. step in the porosity cutoff moves net pay 4%: the beds are either well above or well below it. A 40% Sw cutoff drops the shaly sand's wettest sample and gives 24 ft. A 16% porosity cutoff drops the shaly sand's samples and leaves 20 ft, and the core check warns. A 10 mD permeability cutoff puts core's porosity cutoff at 15.5%, and the core check warns. A 5% Sw cutoff leaves no pay, and the pay check fails.

## Validity

Cutoffs are a convention, not a law: they should be chosen so that what they call pay is rock that flows, from core permeability, capillary pressure and flow tests. They are not the same for oil and gas, or from one rock type to another. A sample counts whole or not at all, so thin beds below the log's resolution are lost or overcounted. Archie's Sw reads too wet in shaly beds. The poro-perm cutoff from core assumes one rock type; split the plugs when they fall on several trends. The net-to-gross here is the reservoir's; some reserves rules use the pay's. The log and core are synthetic. Field units.

Named alternatives: a Thomas-Stieber or high-resolution analysis for a laminated sand; the Shaly-Sand Water Saturation sheet's Sw in the shaly beds; the Permeability from Logs sheet for a poro-perm transform calibrated to core.

## References

- Worthington, P.F. and Cosentino, L. (2005). The Role of Cutoffs in Integrated Reservoir Studies. *SPE Reservoir Evaluation & Engineering* 8(4), 276–290, SPE-84387-PA.
- Worthington, P.F. (2010). Net Pay — What Is It? What Does It Do? How Do We Quantify It? How Do We Use It? *SPE Reservoir Evaluation & Engineering* 13(5), 812–822, SPE-123561-PA.
- Asquith, G. and Krygowski, D. (2004). *Basic Well Log Analysis*, 2nd ed. AAPG Methods in Exploration 16, ch. 4 and 6 (shale volume, porosity and Archie).
- Cosentino, L. (2001). *Integrated Reservoir Studies*. Editions Technip, ch. 3 (net pay and cutoffs).

## Functions used

`PO.PP.Vsh.GammaRayIndex`, `PO.PP.Porosity.FromDensity`, `PO.PP.Sw.Archie`, `PO.PP.Pay.NetPay`, `PO.PP.Cutoff.PermFromCore`

## Spreadsheet: NetPayCutoffs

|     | A                                                                                                                                                                                                                                                             | B                                                                                                                     | C                                                                                                                                                                                                                                                                                                                                                                                                                  | D                                                                                                              | E                                                                                                                  | F                                                                                                                  | G                                                                       | H                                                                    | I                                                    | J                      |
|-----|---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|-----------------------------------------------------------------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------|-------------------------------------------------------------------------|----------------------------------------------------------------------|------------------------------------------------------|------------------------|
| 1   | Net Pay and Cutoffs over an Interval                                                                                                                                                                                                                          |                                                                                                                       | Petroleum Office                                                                                                                                                                                                                                                                                                                                                                                                   |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 2   | Blue cells on yellow are inputs. Set the picks, Archie's parameters and Rw, the gross interval, the three cutoffs and the core's permeability cutoff; paste your own GR, density and deep resistivity over the log below, and your plugs over the core table. |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 3   | The Picks, Archie's Parameters, the Gross Interval and the Cutoffs                                                                                                                                                                                            |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 4   | Clean-sand gamma ray (Vsh = 0)                                                                                                                                                                                                                                | 30                                                                                                                    | API                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 5   | Shale gamma ray (Vsh = 1)                                                                                                                                                                                                                                     | 115                                                                                                                   | API                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 6   | Matrix density (sandstone)                                                                                                                                                                                                                                    | 2.65                                                                                                                  | g/cm³                                                                                                                                                                                                                                                                                                                                                                                                              |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 7   | Fluid density (fresh mud filtrate)                                                                                                                                                                                                                            | 1                                                                                                                     | g/cm³                                                                                                                                                                                                                                                                                                                                                                                                              |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 8   | Shale bulk density, for the shale correction                                                                                                                                                                                                                  | 2.48                                                                                                                  | g/cm³                                                                                                                                                                                                                                                                                                                                                                                                              |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 9   | Tortuosity factor a                                                                                                                                                                                                                                           | 1                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 10  | Cementation exponent m                                                                                                                                                                                                                                        | 2                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 11  | Saturation exponent n                                                                                                                                                                                                                                         | 2                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 12  | Formation-water resistivity at formation temperature                                                                                                                                                                                                          | 0.05                                                                                                                  | ohm·m                                                                                                                                                                                                                                                                                                                                                                                                              |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 13  | Gross interval top (the oil sand's top)                                                                                                                                                                                                                       | 5012                                                                                                                  | ft                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 14  | Gross interval base (the water sand's base)                                                                                                                                                                                                                   | 5100                                                                                                                  | ft                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 15  | Shale-volume cutoff for reservoir                                                                                                                                                                                                                             | 0.4                                                                                                                   | v/v                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 16  | Effective-porosity cutoff for reservoir                                                                                                                                                                                                                       | 0.1                                                                                                                   | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 17  | Water-saturation cutoff for pay                                                                                                                                                                                                                               | 0.6                                                                                                                   | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 18  | Permeability cutoff, for the porosity cutoff from core                                                                                                                                                                                                        | 1                                                                                                                     | mD                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 19  | Agreement limit of the porosity cutoff with core's                                                                                                                                                                                                            | 0.01                                                                                                                  | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 20  | Largest net-pay change for a 2 p.u. step in the porosity cutoff                                                                                                                                                                                               | 0.25                                                                                                                  | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 24  | Gross, Net Reservoir and Net Pay, the Pay's Averages and the Core's Porosity Cutoff                                                                                                                                                                           |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 25  | Log sample spacing                                                                                                                                                                                                                                            | =(MAX($A$88:$A$148)-MIN($A$88:$A$148))/(COUNT($A$88:$A$148)-1)                                                        | ft                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 26  | Shale's density porosity, the shale correction                                                                                                                                                                                                                | =PO.PP.Porosity.FromDensity(NP_RhoMa,NP_RhoSh,NP_RhoF)                                                                | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 27  | Gross interval mean shale volume                                                                                                                                                                                                                              | =SUMPRODUCT($E$88:$E$148,$F$88:$F$148)/SUM($E$88:$E$148)                                                              | v/v                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 28  | Gross interval mean effective porosity                                                                                                                                                                                                                        | =SUMPRODUCT($E$88:$E$148,$G$88:$G$148)/SUM($E$88:$E$148)                                                              | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 29  | Gross interval mean water saturation                                                                                                                                                                                                                          | =SUMPRODUCT($E$88:$E$148,$H$88:$H$148)/SUM($E$88:$E$148)                                                              | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 30  | Gross thickness                                                                                                                                                                                                                                               | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,NP_PhiCut,NP_SwCut),1)          | ft                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 31  | Net reservoir (Vsh and porosity cutoffs)                                                                                                                                                                                                                      | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,NP_PhiCut,NP_SwCut),2)          | ft                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 32  | Net pay (and the Sw cutoff)                                                                                                                                                                                                                                   | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,NP_PhiCut,NP_SwCut),NP_OutPay)  | ft                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 33  | Net-to-gross, net reservoir over gross                                                                                                                                                                                                                        | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,NP_PhiCut,NP_SwCut),NP_OutNTG)  | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 34  | Pay over gross                                                                                                                                                                                                                                                | =NP_Pay/NP_Gross                                                                                                      | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 35  | Pay's mean porosity                                                                                                                                                                                                                                           | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,NP_PhiCut,NP_SwCut),NP_OutPhi)  | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 36  | Pay's mean water saturation (pore-volume weighted)                                                                                                                                                                                                            | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,NP_PhiCut,NP_SwCut),NP_OutSw)   | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 37  | Hydrocarbon pore thickness of the pay, φ (1 − Sw) h                                                                                                                                                                                                           | =NP_Pay*NP_PayPhi*(1-NP_PaySw)                                                                                        | ft                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 38  | Core plugs                                                                                                                                                                                                                                                    | =COUNT($B$62:$B$76)                                                                                                   | —                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 39  | Porosity cutoff from core at the permeability cutoff                                                                                                                                                                                                          | =PO.PP.Cutoff.PermFromCore($B$62:$B$76,$C$62:$C$76,NP_KCut)                                                           | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 40  | Net pay at core's porosity cutoff                                                                                                                                                                                                                             | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,NP_PhiCore,NP_SwCut),NP_OutPay) | ft                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 41  | Net-pay change per 2 p.u. of porosity cutoff                                                                                                                                                                                                                  | =IF(NP_Pay>0,(D52-D54)/2/NP_Pay,0)                                                                                    | %                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 42  | Pay check                                                                                                                                                                                                                                                     | =IF(NP_Pay>0,"PASS","FAIL")                                                                                           | =IF(NP_Pay>0,""&FIXED(NP_Pay,0)&" ft of net pay in "&FIXED(NP_Gross,0)&" ft gross, at a mean porosity of "&FIXED(NP_PayPhi*100,1)&"% and Sw of "&FIXED(NP_PaySw*100,1)&"%","no sample passes all three cutoffs: the interval has no pay at these cutoffs")                                                                                                                                                         |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 43  | Core cutoff check                                                                                                                                                                                                                                             | =IF(NP_Plugs<=2,"FAIL",IF(ABS(NP_PhiCore-NP_PhiCut)<=NP_CutTol,"PASS","WARN"))                                        | =IF(NP_Plugs<=2,"the core cutoff needs three plugs or more",IF(ABS(NP_PhiCore-NP_PhiCut)<=NP_CutTol,"core puts "&FIXED(NP_KCut,1)&" mD at "&FIXED(NP_PhiCore*100,1)&"% porosity, within "&FIXED(NP_CutTol*100,1)&" p.u. of the cutoff","core puts "&FIXED(NP_KCut,1)&" mD at "&FIXED(NP_PhiCore*100,1)&"% porosity, not the "&FIXED(NP_PhiCut*100,1)&"% cutoff: net pay is "&FIXED(NP_PayCore,0)&" ft at core's")) |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 44  | Cutoff sensitivity check                                                                                                                                                                                                                                      | =IF(NP_Sens<=NP_SensMax,"PASS","WARN")                                                                                | =IF(NP_Sens<=NP_SensMax,"a 2 p.u. change in the porosity cutoff moves net pay "&FIXED(NP_Sens*100,0)&"%: the cutoff falls where little rock is","a 2 p.u. change in the porosity cutoff moves net pay "&FIXED(NP_Sens*100,0)&"%: much rock sits near the cutoff, so tie it to core and flow tests")                                                                                                                |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 46  | How to use it: paste your depth, GR, bulk density and deep resistivity over the log table, and your plugs' porosity and permeability over the core table; set the cutoffs from core and flow tests, not by habit.                                             |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 47  | The log and core are synthetic, the log display workbook's interval. Each sample stands for the log spacing; outside the gross interval it counts for nothing.                                                                                                |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 49  | Net Pay over the Porosity Cutoff (down) and the Sw Cutoff (across)                                                                                                                                                                                            |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 50  | Porosity cutoff (%)                                                                                                                                                                                                                                           | Sw cut − 0.2 (ft)                                                                                                     | Sw cut − 0.1 (ft)                                                                                                                                                                                                                                                                                                                                                                                                  | Sw cut (ft)                                                                                                    | Sw cut + 0.1 (ft)                                                                                                  | Sw cut + 0.2 (ft)                                                                                                  |                                                                         |                                                                      |                                                      |                        |
| 51  | =NP_PhiCut-0.04                                                                                                                                                                                                                                               | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A51,NP_SwCut-0.2),NP_OutPay)    | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A51,NP_SwCut-0.1),NP_OutPay)                                                                                                                                                                                                                                                                                                 | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A51,NP_SwCut),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A51,NP_SwCut+0.1),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A51,NP_SwCut+0.2),NP_OutPay) |                                                                         |                                                                      |                                                      |                        |
| 52  | =NP_PhiCut-0.02                                                                                                                                                                                                                                               | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A52,NP_SwCut-0.2),NP_OutPay)    | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A52,NP_SwCut-0.1),NP_OutPay)                                                                                                                                                                                                                                                                                                 | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A52,NP_SwCut),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A52,NP_SwCut+0.1),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A52,NP_SwCut+0.2),NP_OutPay) |                                                                         |                                                                      |                                                      |                        |
| 53  | =NP_PhiCut                                                                                                                                                                                                                                                    | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A53,NP_SwCut-0.2),NP_OutPay)    | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A53,NP_SwCut-0.1),NP_OutPay)                                                                                                                                                                                                                                                                                                 | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A53,NP_SwCut),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A53,NP_SwCut+0.1),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A53,NP_SwCut+0.2),NP_OutPay) |                                                                         |                                                                      |                                                      |                        |
| 54  | =NP_PhiCut+0.02                                                                                                                                                                                                                                               | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A54,NP_SwCut-0.2),NP_OutPay)    | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A54,NP_SwCut-0.1),NP_OutPay)                                                                                                                                                                                                                                                                                                 | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A54,NP_SwCut),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A54,NP_SwCut+0.1),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A54,NP_SwCut+0.2),NP_OutPay) |                                                                         |                                                                      |                                                      |                        |
| 55  | =NP_PhiCut+0.04                                                                                                                                                                                                                                               | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A55,NP_SwCut-0.2),NP_OutPay)    | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A55,NP_SwCut-0.1),NP_OutPay)                                                                                                                                                                                                                                                                                                 | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A55,NP_SwCut),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A55,NP_SwCut+0.1),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A55,NP_SwCut+0.2),NP_OutPay) |                                                                         |                                                                      |                                                      |                        |
| 56  | =NP_PhiCut+0.06                                                                                                                                                                                                                                               | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A56,NP_SwCut-0.2),NP_OutPay)    | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A56,NP_SwCut-0.1),NP_OutPay)                                                                                                                                                                                                                                                                                                 | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A56,NP_SwCut),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A56,NP_SwCut+0.1),NP_OutPay) | =INDEX(PO.PP.Pay.NetPay($E$88:$E$148,$F$88:$F$148,$G$88:$G$148,$H$88:$H$148,NP_VshCut,A56,NP_SwCut+0.2),NP_OutPay) |                                                                         |                                                                      |                                                      |                        |
| 60  | Core Plugs (helium porosity and air permeability)                                                                                                                                                                                                             |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 61  | Core depth (ft)                                                                                                                                                                                                                                               | φ core (%)                                                                                                            | k core (mD)                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 62  | 5017                                                                                                                                                                                                                                                          | 0.254                                                                                                                 | 1130                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 63  | 5019                                                                                                                                                                                                                                                          | 0.263                                                                                                                 | 1330                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 64  | 5021                                                                                                                                                                                                                                                          | 0.269                                                                                                                 | 1110                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 65  | 5025                                                                                                                                                                                                                                                          | 0.261                                                                                                                 | 1790                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 66  | 5029                                                                                                                                                                                                                                                          | 0.27                                                                                                                  | 1380                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 67  | 5033                                                                                                                                                                                                                                                          | 0.264                                                                                                                 | 1110                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 68  | 5045                                                                                                                                                                                                                                                          | 0.193                                                                                                                 | 90                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 69  | 5049                                                                                                                                                                                                                                                          | 0.191                                                                                                                 | 36                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 70  | 5055                                                                                                                                                                                                                                                          | 0.194                                                                                                                 | 68                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 71  | 5059                                                                                                                                                                                                                                                          | 0.182                                                                                                                 | 47                                                                                                                                                                                                                                                                                                                                                                                                                 |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 72  | 5077                                                                                                                                                                                                                                                          | 0.053                                                                                                                 | 0.08                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 73  | 5085                                                                                                                                                                                                                                                          | 0.253                                                                                                                 | 1150                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 74  | 5089                                                                                                                                                                                                                                                          | 0.259                                                                                                                 | 1040                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 75  | 5093                                                                                                                                                                                                                                                          | 0.255                                                                                                                 | 630                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 76  | 5097                                                                                                                                                                                                                                                          | 0.258                                                                                                                 | 1590                                                                                                                                                                                                                                                                                                                                                                                                               |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 79  | Constants (the place of each output in the net-pay function's six)                                                                                                                                                                                            |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 80  | Net pay, third of the six                                                                                                                                                                                                                                     | 3                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 81  | Net-to-gross, fourth                                                                                                                                                                                                                                          | 4                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 82  | Pay's mean porosity, fifth                                                                                                                                                                                                                                    | 5                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 83  | Pay's mean water saturation, sixth                                                                                                                                                                                                                            | 6                                                                                                                     | —                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 86  | Log: Readings, Vsh, Porosity, Sw and the Flags (the log display workbook's interval every 2 ft)                                                                                                                                                               |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                                |                                                                                                                    |                                                                                                                    |                                                                         |                                                                      |                                                      |                        |
| 87  | Depth (ft)                                                                                                                                                                                                                                                    | GR (API)                                                                                                              | RHOB (g/cm³)                                                                                                                                                                                                                                                                                                                                                                                                       | Rt (ohm·m)                                                                                                     | h in gross (ft)                                                                                                    | Vsh (v/v)                                                                                                          | φ effective (%)                                                         | Sw, Archie (%)                                                       | Reservoir                                            | Pay                    |
| 88  | 5000                                                                                                                                                                                                                                                          | 111.3                                                                                                                 | 2.479                                                                                                                                                                                                                                                                                                                                                                                                              | 2.43                                                                                                           | =IF(AND(A88>=NP_Top,A88<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B88,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C88,NP_RhoF)-F88*NP_PhiSh)   | =IF(G88>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G88,NP_Rw,D88)),1)    | =IF(AND(E88>0,F88<=NP_VshCut,G88>=NP_PhiCut),1,0)    | =I88*(H88<=NP_SwCut)   |
| 89  | 5002                                                                                                                                                                                                                                                          | 116.4                                                                                                                 | 2.482                                                                                                                                                                                                                                                                                                                                                                                                              | 2.44                                                                                                           | =IF(AND(A89>=NP_Top,A89<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B89,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C89,NP_RhoF)-F89*NP_PhiSh)   | =IF(G89>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G89,NP_Rw,D89)),1)    | =IF(AND(E89>0,F89<=NP_VshCut,G89>=NP_PhiCut),1,0)    | =I89*(H89<=NP_SwCut)   |
| 90  | 5004                                                                                                                                                                                                                                                          | 114.4                                                                                                                 | 2.475                                                                                                                                                                                                                                                                                                                                                                                                              | 2.46                                                                                                           | =IF(AND(A90>=NP_Top,A90<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B90,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C90,NP_RhoF)-F90*NP_PhiSh)   | =IF(G90>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G90,NP_Rw,D90)),1)    | =IF(AND(E90>0,F90<=NP_VshCut,G90>=NP_PhiCut),1,0)    | =I90*(H90<=NP_SwCut)   |
| 91  | 5006                                                                                                                                                                                                                                                          | 113.2                                                                                                                 | 2.481                                                                                                                                                                                                                                                                                                                                                                                                              | 2.38                                                                                                           | =IF(AND(A91>=NP_Top,A91<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B91,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C91,NP_RhoF)-F91*NP_PhiSh)   | =IF(G91>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G91,NP_Rw,D91)),1)    | =IF(AND(E91>0,F91<=NP_VshCut,G91>=NP_PhiCut),1,0)    | =I91*(H91<=NP_SwCut)   |
| 92  | 5008                                                                                                                                                                                                                                                          | 114.2                                                                                                                 | 2.476                                                                                                                                                                                                                                                                                                                                                                                                              | 2.46                                                                                                           | =IF(AND(A92>=NP_Top,A92<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B92,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C92,NP_RhoF)-F92*NP_PhiSh)   | =IF(G92>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G92,NP_Rw,D92)),1)    | =IF(AND(E92>0,F92<=NP_VshCut,G92>=NP_PhiCut),1,0)    | =I92*(H92<=NP_SwCut)   |
| 93  | 5010                                                                                                                                                                                                                                                          | 108.4                                                                                                                 | 2.462                                                                                                                                                                                                                                                                                                                                                                                                              | 3.27                                                                                                           | =IF(AND(A93>=NP_Top,A93<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B93,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C93,NP_RhoF)-F93*NP_PhiSh)   | =IF(G93>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G93,NP_Rw,D93)),1)    | =IF(AND(E93>0,F93<=NP_VshCut,G93>=NP_PhiCut),1,0)    | =I93*(H93<=NP_SwCut)   |
| 94  | 5012                                                                                                                                                                                                                                                          | 73.9                                                                                                                  | 2.339                                                                                                                                                                                                                                                                                                                                                                                                              | 10                                                                                                             | =IF(AND(A94>=NP_Top,A94<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B94,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C94,NP_RhoF)-F94*NP_PhiSh)   | =IF(G94>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G94,NP_Rw,D94)),1)    | =IF(AND(E94>0,F94<=NP_VshCut,G94>=NP_PhiCut),1,0)    | =I94*(H94<=NP_SwCut)   |
| 95  | 5014                                                                                                                                                                                                                                                          | 35.2                                                                                                                  | 2.237                                                                                                                                                                                                                                                                                                                                                                                                              | 41.2                                                                                                           | =IF(AND(A95>=NP_Top,A95<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B95,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C95,NP_RhoF)-F95*NP_PhiSh)   | =IF(G95>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G95,NP_Rw,D95)),1)    | =IF(AND(E95>0,F95<=NP_VshCut,G95>=NP_PhiCut),1,0)    | =I95*(H95<=NP_SwCut)   |
| 96  | 5016                                                                                                                                                                                                                                                          | 36.1                                                                                                                  | 2.209                                                                                                                                                                                                                                                                                                                                                                                                              | 46.3                                                                                                           | =IF(AND(A96>=NP_Top,A96<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B96,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C96,NP_RhoF)-F96*NP_PhiSh)   | =IF(G96>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G96,NP_Rw,D96)),1)    | =IF(AND(E96>0,F96<=NP_VshCut,G96>=NP_PhiCut),1,0)    | =I96*(H96<=NP_SwCut)   |
| 97  | 5018                                                                                                                                                                                                                                                          | 29.5                                                                                                                  | 2.212                                                                                                                                                                                                                                                                                                                                                                                                              | 50.6                                                                                                           | =IF(AND(A97>=NP_Top,A97<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B97,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C97,NP_RhoF)-F97*NP_PhiSh)   | =IF(G97>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G97,NP_Rw,D97)),1)    | =IF(AND(E97>0,F97<=NP_VshCut,G97>=NP_PhiCut),1,0)    | =I97*(H97<=NP_SwCut)   |
| 98  | 5020                                                                                                                                                                                                                                                          | 33.4                                                                                                                  | 2.21                                                                                                                                                                                                                                                                                                                                                                                                               | 44.8                                                                                                           | =IF(AND(A98>=NP_Top,A98<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B98,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C98,NP_RhoF)-F98*NP_PhiSh)   | =IF(G98>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G98,NP_Rw,D98)),1)    | =IF(AND(E98>0,F98<=NP_VshCut,G98>=NP_PhiCut),1,0)    | =I98*(H98<=NP_SwCut)   |
| 99  | 5022                                                                                                                                                                                                                                                          | 31.1                                                                                                                  | 2.214                                                                                                                                                                                                                                                                                                                                                                                                              | 52.3                                                                                                           | =IF(AND(A99>=NP_Top,A99<NP_Base),NP_Step,0)                                                                        | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B99,NP_GRcl,NP_GRsh)))                                                        | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C99,NP_RhoF)-F99*NP_PhiSh)   | =IF(G99>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G99,NP_Rw,D99)),1)    | =IF(AND(E99>0,F99<=NP_VshCut,G99>=NP_PhiCut),1,0)    | =I99*(H99<=NP_SwCut)   |
| 100 | 5024                                                                                                                                                                                                                                                          | 35                                                                                                                    | 2.209                                                                                                                                                                                                                                                                                                                                                                                                              | 46.1                                                                                                           | =IF(AND(A100>=NP_Top,A100<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B100,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C100,NP_RhoF)-F100*NP_PhiSh) | =IF(G100>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G100,NP_Rw,D100)),1) | =IF(AND(E100>0,F100<=NP_VshCut,G100>=NP_PhiCut),1,0) | =I100*(H100<=NP_SwCut) |
| 101 | 5026                                                                                                                                                                                                                                                          | 29.8                                                                                                                  | 2.21                                                                                                                                                                                                                                                                                                                                                                                                               | 47.4                                                                                                           | =IF(AND(A101>=NP_Top,A101<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B101,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C101,NP_RhoF)-F101*NP_PhiSh) | =IF(G101>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G101,NP_Rw,D101)),1) | =IF(AND(E101>0,F101<=NP_VshCut,G101>=NP_PhiCut),1,0) | =I101*(H101<=NP_SwCut) |
| 102 | 5028                                                                                                                                                                                                                                                          | 34                                                                                                                    | 2.216                                                                                                                                                                                                                                                                                                                                                                                                              | 48.3                                                                                                           | =IF(AND(A102>=NP_Top,A102<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B102,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C102,NP_RhoF)-F102*NP_PhiSh) | =IF(G102>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G102,NP_Rw,D102)),1) | =IF(AND(E102>0,F102<=NP_VshCut,G102>=NP_PhiCut),1,0) | =I102*(H102<=NP_SwCut) |
| 103 | 5030                                                                                                                                                                                                                                                          | 34                                                                                                                    | 2.208                                                                                                                                                                                                                                                                                                                                                                                                              | 46.7                                                                                                           | =IF(AND(A103>=NP_Top,A103<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B103,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C103,NP_RhoF)-F103*NP_PhiSh) | =IF(G103>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G103,NP_Rw,D103)),1) | =IF(AND(E103>0,F103<=NP_VshCut,G103>=NP_PhiCut),1,0) | =I103*(H103<=NP_SwCut) |
| 104 | 5032                                                                                                                                                                                                                                                          | 37.5                                                                                                                  | 2.234                                                                                                                                                                                                                                                                                                                                                                                                              | 37.3                                                                                                           | =IF(AND(A104>=NP_Top,A104<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B104,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C104,NP_RhoF)-F104*NP_PhiSh) | =IF(G104>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G104,NP_Rw,D104)),1) | =IF(AND(E104>0,F104<=NP_VshCut,G104>=NP_PhiCut),1,0) | =I104*(H104<=NP_SwCut) |
| 105 | 5034                                                                                                                                                                                                                                                          | 74.7                                                                                                                  | 2.344                                                                                                                                                                                                                                                                                                                                                                                                              | 10.3                                                                                                           | =IF(AND(A105>=NP_Top,A105<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B105,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C105,NP_RhoF)-F105*NP_PhiSh) | =IF(G105>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G105,NP_Rw,D105)),1) | =IF(AND(E105>0,F105<=NP_VshCut,G105>=NP_PhiCut),1,0) | =I105*(H105<=NP_SwCut) |
| 106 | 5036                                                                                                                                                                                                                                                          | 108.7                                                                                                                 | 2.463                                                                                                                                                                                                                                                                                                                                                                                                              | 3.25                                                                                                           | =IF(AND(A106>=NP_Top,A106<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B106,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C106,NP_RhoF)-F106*NP_PhiSh) | =IF(G106>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G106,NP_Rw,D106)),1) | =IF(AND(E106>0,F106<=NP_VshCut,G106>=NP_PhiCut),1,0) | =I106*(H106<=NP_SwCut) |
| 107 | 5038                                                                                                                                                                                                                                                          | 112.2                                                                                                                 | 2.461                                                                                                                                                                                                                                                                                                                                                                                                              | 2.57                                                                                                           | =IF(AND(A107>=NP_Top,A107<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B107,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C107,NP_RhoF)-F107*NP_PhiSh) | =IF(G107>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G107,NP_Rw,D107)),1) | =IF(AND(E107>0,F107<=NP_VshCut,G107>=NP_PhiCut),1,0) | =I107*(H107<=NP_SwCut) |
| 108 | 5040                                                                                                                                                                                                                                                          | 85.4                                                                                                                  | 2.41                                                                                                                                                                                                                                                                                                                                                                                                               | 6.84                                                                                                           | =IF(AND(A108>=NP_Top,A108<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B108,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C108,NP_RhoF)-F108*NP_PhiSh) | =IF(G108>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G108,NP_Rw,D108)),1) | =IF(AND(E108>0,F108<=NP_VshCut,G108>=NP_PhiCut),1,0) | =I108*(H108<=NP_SwCut) |
| 109 | 5042                                                                                                                                                                                                                                                          | 69.7                                                                                                                  | 2.338                                                                                                                                                                                                                                                                                                                                                                                                              | 14.8                                                                                                           | =IF(AND(A109>=NP_Top,A109<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B109,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C109,NP_RhoF)-F109*NP_PhiSh) | =IF(G109>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G109,NP_Rw,D109)),1) | =IF(AND(E109>0,F109<=NP_VshCut,G109>=NP_PhiCut),1,0) | =I109*(H109<=NP_SwCut) |
| 110 | 5044                                                                                                                                                                                                                                                          | 59.9                                                                                                                  | 2.33                                                                                                                                                                                                                                                                                                                                                                                                               | 18.3                                                                                                           | =IF(AND(A110>=NP_Top,A110<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B110,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C110,NP_RhoF)-F110*NP_PhiSh) | =IF(G110>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G110,NP_Rw,D110)),1) | =IF(AND(E110>0,F110<=NP_VshCut,G110>=NP_PhiCut),1,0) | =I110*(H110<=NP_SwCut) |
| 111 | 5046                                                                                                                                                                                                                                                          | 62.8                                                                                                                  | 2.329                                                                                                                                                                                                                                                                                                                                                                                                              | 15.5                                                                                                           | =IF(AND(A111>=NP_Top,A111<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B111,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C111,NP_RhoF)-F111*NP_PhiSh) | =IF(G111>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G111,NP_Rw,D111)),1) | =IF(AND(E111>0,F111<=NP_VshCut,G111>=NP_PhiCut),1,0) | =I111*(H111<=NP_SwCut) |
| 112 | 5048                                                                                                                                                                                                                                                          | 60.8                                                                                                                  | 2.333                                                                                                                                                                                                                                                                                                                                                                                                              | 10.3                                                                                                           | =IF(AND(A112>=NP_Top,A112<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B112,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C112,NP_RhoF)-F112*NP_PhiSh) | =IF(G112>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G112,NP_Rw,D112)),1) | =IF(AND(E112>0,F112<=NP_VshCut,G112>=NP_PhiCut),1,0) | =I112*(H112<=NP_SwCut) |
| 113 | 5050                                                                                                                                                                                                                                                          | 65.4                                                                                                                  | 2.335                                                                                                                                                                                                                                                                                                                                                                                                              | 2.01                                                                                                           | =IF(AND(A113>=NP_Top,A113<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B113,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C113,NP_RhoF)-F113*NP_PhiSh) | =IF(G113>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G113,NP_Rw,D113)),1) | =IF(AND(E113>0,F113<=NP_VshCut,G113>=NP_PhiCut),1,0) | =I113*(H113<=NP_SwCut) |
| 114 | 5052                                                                                                                                                                                                                                                          | 61.1                                                                                                                  | 2.336                                                                                                                                                                                                                                                                                                                                                                                                              | 1.15                                                                                                           | =IF(AND(A114>=NP_Top,A114<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B114,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C114,NP_RhoF)-F114*NP_PhiSh) | =IF(G114>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G114,NP_Rw,D114)),1) | =IF(AND(E114>0,F114<=NP_VshCut,G114>=NP_PhiCut),1,0) | =I114*(H114<=NP_SwCut) |
| 115 | 5054                                                                                                                                                                                                                                                          | 64.1                                                                                                                  | 2.345                                                                                                                                                                                                                                                                                                                                                                                                              | 1.15                                                                                                           | =IF(AND(A115>=NP_Top,A115<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B115,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C115,NP_RhoF)-F115*NP_PhiSh) | =IF(G115>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G115,NP_Rw,D115)),1) | =IF(AND(E115>0,F115<=NP_VshCut,G115>=NP_PhiCut),1,0) | =I115*(H115<=NP_SwCut) |
| 116 | 5056                                                                                                                                                                                                                                                          | 68.7                                                                                                                  | 2.345                                                                                                                                                                                                                                                                                                                                                                                                              | 1.18                                                                                                           | =IF(AND(A116>=NP_Top,A116<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B116,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C116,NP_RhoF)-F116*NP_PhiSh) | =IF(G116>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G116,NP_Rw,D116)),1) | =IF(AND(E116>0,F116<=NP_VshCut,G116>=NP_PhiCut),1,0) | =I116*(H116<=NP_SwCut) |
| 117 | 5058                                                                                                                                                                                                                                                          | 87.1                                                                                                                  | 2.412                                                                                                                                                                                                                                                                                                                                                                                                              | 1.66                                                                                                           | =IF(AND(A117>=NP_Top,A117<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B117,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C117,NP_RhoF)-F117*NP_PhiSh) | =IF(G117>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G117,NP_Rw,D117)),1) | =IF(AND(E117>0,F117<=NP_VshCut,G117>=NP_PhiCut),1,0) | =I117*(H117<=NP_SwCut) |
| 118 | 5060                                                                                                                                                                                                                                                          | 111.4                                                                                                                 | 2.467                                                                                                                                                                                                                                                                                                                                                                                                              | 2.19                                                                                                           | =IF(AND(A118>=NP_Top,A118<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B118,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C118,NP_RhoF)-F118*NP_PhiSh) | =IF(G118>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G118,NP_Rw,D118)),1) | =IF(AND(E118>0,F118<=NP_VshCut,G118>=NP_PhiCut),1,0) | =I118*(H118<=NP_SwCut) |
| 119 | 5062                                                                                                                                                                                                                                                          | 113.6                                                                                                                 | 2.483                                                                                                                                                                                                                                                                                                                                                                                                              | 2.66                                                                                                           | =IF(AND(A119>=NP_Top,A119<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B119,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C119,NP_RhoF)-F119*NP_PhiSh) | =IF(G119>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G119,NP_Rw,D119)),1) | =IF(AND(E119>0,F119<=NP_VshCut,G119>=NP_PhiCut),1,0) | =I119*(H119<=NP_SwCut) |
| 120 | 5064                                                                                                                                                                                                                                                          | 116.6                                                                                                                 | 2.474                                                                                                                                                                                                                                                                                                                                                                                                              | 2.24                                                                                                           | =IF(AND(A120>=NP_Top,A120<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B120,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C120,NP_RhoF)-F120*NP_PhiSh) | =IF(G120>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G120,NP_Rw,D120)),1) | =IF(AND(E120>0,F120<=NP_VshCut,G120>=NP_PhiCut),1,0) | =I120*(H120<=NP_SwCut) |
| 121 | 5066                                                                                                                                                                                                                                                          | 111.2                                                                                                                 | 2.485                                                                                                                                                                                                                                                                                                                                                                                                              | 2.56                                                                                                           | =IF(AND(A121>=NP_Top,A121<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B121,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C121,NP_RhoF)-F121*NP_PhiSh) | =IF(G121>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G121,NP_Rw,D121)),1) | =IF(AND(E121>0,F121<=NP_VshCut,G121>=NP_PhiCut),1,0) | =I121*(H121<=NP_SwCut) |
| 122 | 5068                                                                                                                                                                                                                                                          | 117.9                                                                                                                 | 2.48                                                                                                                                                                                                                                                                                                                                                                                                               | 2.45                                                                                                           | =IF(AND(A122>=NP_Top,A122<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B122,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C122,NP_RhoF)-F122*NP_PhiSh) | =IF(G122>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G122,NP_Rw,D122)),1) | =IF(AND(E122>0,F122<=NP_VshCut,G122>=NP_PhiCut),1,0) | =I122*(H122<=NP_SwCut) |
| 123 | 5070                                                                                                                                                                                                                                                          | 106.2                                                                                                                 | 2.488                                                                                                                                                                                                                                                                                                                                                                                                              | 3.74                                                                                                           | =IF(AND(A123>=NP_Top,A123<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B123,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C123,NP_RhoF)-F123*NP_PhiSh) | =IF(G123>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G123,NP_Rw,D123)),1) | =IF(AND(E123>0,F123<=NP_VshCut,G123>=NP_PhiCut),1,0) | =I123*(H123<=NP_SwCut) |
| 124 | 5072                                                                                                                                                                                                                                                          | 69.6                                                                                                                  | 2.53                                                                                                                                                                                                                                                                                                                                                                                                               | 29.3                                                                                                           | =IF(AND(A124>=NP_Top,A124<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B124,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C124,NP_RhoF)-F124*NP_PhiSh) | =IF(G124>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G124,NP_Rw,D124)),1) | =IF(AND(E124>0,F124<=NP_VshCut,G124>=NP_PhiCut),1,0) | =I124*(H124<=NP_SwCut) |
| 125 | 5074                                                                                                                                                                                                                                                          | 28.7                                                                                                                  | 2.567                                                                                                                                                                                                                                                                                                                                                                                                              | 259                                                                                                            | =IF(AND(A125>=NP_Top,A125<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B125,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C125,NP_RhoF)-F125*NP_PhiSh) | =IF(G125>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G125,NP_Rw,D125)),1) | =IF(AND(E125>0,F125<=NP_VshCut,G125>=NP_PhiCut),1,0) | =I125*(H125<=NP_SwCut) |
| 126 | 5076                                                                                                                                                                                                                                                          | 28.4                                                                                                                  | 2.502                                                                                                                                                                                                                                                                                                                                                                                                              | 98.6                                                                                                           | =IF(AND(A126>=NP_Top,A126<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B126,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C126,NP_RhoF)-F126*NP_PhiSh) | =IF(G126>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G126,NP_Rw,D126)),1) | =IF(AND(E126>0,F126<=NP_VshCut,G126>=NP_PhiCut),1,0) | =I126*(H126<=NP_SwCut) |
| 127 | 5078                                                                                                                                                                                                                                                          | 31.9                                                                                                                  | 2.306                                                                                                                                                                                                                                                                                                                                                                                                              | 2.92                                                                                                           | =IF(AND(A127>=NP_Top,A127<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B127,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C127,NP_RhoF)-F127*NP_PhiSh) | =IF(G127>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G127,NP_Rw,D127)),1) | =IF(AND(E127>0,F127<=NP_VshCut,G127>=NP_PhiCut),1,0) | =I127*(H127<=NP_SwCut) |
| 128 | 5080                                                                                                                                                                                                                                                          | 36                                                                                                                    | 2.245                                                                                                                                                                                                                                                                                                                                                                                                              | 0.885                                                                                                          | =IF(AND(A128>=NP_Top,A128<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B128,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C128,NP_RhoF)-F128*NP_PhiSh) | =IF(G128>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G128,NP_Rw,D128)),1) | =IF(AND(E128>0,F128<=NP_VshCut,G128>=NP_PhiCut),1,0) | =I128*(H128<=NP_SwCut) |
| 129 | 5082                                                                                                                                                                                                                                                          | 38.7                                                                                                                  | 2.227                                                                                                                                                                                                                                                                                                                                                                                                              | 0.742                                                                                                          | =IF(AND(A129>=NP_Top,A129<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B129,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C129,NP_RhoF)-F129*NP_PhiSh) | =IF(G129>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G129,NP_Rw,D129)),1) | =IF(AND(E129>0,F129<=NP_VshCut,G129>=NP_PhiCut),1,0) | =I129*(H129<=NP_SwCut) |
| 130 | 5084                                                                                                                                                                                                                                                          | 34.6                                                                                                                  | 2.233                                                                                                                                                                                                                                                                                                                                                                                                              | 0.751                                                                                                          | =IF(AND(A130>=NP_Top,A130<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B130,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C130,NP_RhoF)-F130*NP_PhiSh) | =IF(G130>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G130,NP_Rw,D130)),1) | =IF(AND(E130>0,F130<=NP_VshCut,G130>=NP_PhiCut),1,0) | =I130*(H130<=NP_SwCut) |
| 131 | 5086                                                                                                                                                                                                                                                          | 37.5                                                                                                                  | 2.228                                                                                                                                                                                                                                                                                                                                                                                                              | 0.693                                                                                                          | =IF(AND(A131>=NP_Top,A131<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B131,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C131,NP_RhoF)-F131*NP_PhiSh) | =IF(G131>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G131,NP_Rw,D131)),1) | =IF(AND(E131>0,F131<=NP_VshCut,G131>=NP_PhiCut),1,0) | =I131*(H131<=NP_SwCut) |
| 132 | 5088                                                                                                                                                                                                                                                          | 35.5                                                                                                                  | 2.235                                                                                                                                                                                                                                                                                                                                                                                                              | 0.812                                                                                                          | =IF(AND(A132>=NP_Top,A132<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B132,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C132,NP_RhoF)-F132*NP_PhiSh) | =IF(G132>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G132,NP_Rw,D132)),1) | =IF(AND(E132>0,F132<=NP_VshCut,G132>=NP_PhiCut),1,0) | =I132*(H132<=NP_SwCut) |
| 133 | 5090                                                                                                                                                                                                                                                          | 38.7                                                                                                                  | 2.224                                                                                                                                                                                                                                                                                                                                                                                                              | 0.681                                                                                                          | =IF(AND(A133>=NP_Top,A133<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B133,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C133,NP_RhoF)-F133*NP_PhiSh) | =IF(G133>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G133,NP_Rw,D133)),1) | =IF(AND(E133>0,F133<=NP_VshCut,G133>=NP_PhiCut),1,0) | =I133*(H133<=NP_SwCut) |
| 134 | 5092                                                                                                                                                                                                                                                          | 32.3                                                                                                                  | 2.233                                                                                                                                                                                                                                                                                                                                                                                                              | 0.769                                                                                                          | =IF(AND(A134>=NP_Top,A134<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B134,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C134,NP_RhoF)-F134*NP_PhiSh) | =IF(G134>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G134,NP_Rw,D134)),1) | =IF(AND(E134>0,F134<=NP_VshCut,G134>=NP_PhiCut),1,0) | =I134*(H134<=NP_SwCut) |
| 135 | 5094                                                                                                                                                                                                                                                          | 39.2                                                                                                                  | 2.229                                                                                                                                                                                                                                                                                                                                                                                                              | 0.727                                                                                                          | =IF(AND(A135>=NP_Top,A135<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B135,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C135,NP_RhoF)-F135*NP_PhiSh) | =IF(G135>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G135,NP_Rw,D135)),1) | =IF(AND(E135>0,F135<=NP_VshCut,G135>=NP_PhiCut),1,0) | =I135*(H135<=NP_SwCut) |
| 136 | 5096                                                                                                                                                                                                                                                          | 34.9                                                                                                                  | 2.229                                                                                                                                                                                                                                                                                                                                                                                                              | 0.784                                                                                                          | =IF(AND(A136>=NP_Top,A136<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B136,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C136,NP_RhoF)-F136*NP_PhiSh) | =IF(G136>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G136,NP_Rw,D136)),1) | =IF(AND(E136>0,F136<=NP_VshCut,G136>=NP_PhiCut),1,0) | =I136*(H136<=NP_SwCut) |
| 137 | 5098                                                                                                                                                                                                                                                          | 42                                                                                                                    | 2.248                                                                                                                                                                                                                                                                                                                                                                                                              | 0.767                                                                                                          | =IF(AND(A137>=NP_Top,A137<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B137,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C137,NP_RhoF)-F137*NP_PhiSh) | =IF(G137>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G137,NP_Rw,D137)),1) | =IF(AND(E137>0,F137<=NP_VshCut,G137>=NP_PhiCut),1,0) | =I137*(H137<=NP_SwCut) |
| 138 | 5100                                                                                                                                                                                                                                                          | 74                                                                                                                    | 2.355                                                                                                                                                                                                                                                                                                                                                                                                              | 1.39                                                                                                           | =IF(AND(A138>=NP_Top,A138<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B138,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C138,NP_RhoF)-F138*NP_PhiSh) | =IF(G138>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G138,NP_Rw,D138)),1) | =IF(AND(E138>0,F138<=NP_VshCut,G138>=NP_PhiCut),1,0) | =I138*(H138<=NP_SwCut) |
| 139 | 5102                                                                                                                                                                                                                                                          | 110.2                                                                                                                 | 2.461                                                                                                                                                                                                                                                                                                                                                                                                              | 2.25                                                                                                           | =IF(AND(A139>=NP_Top,A139<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B139,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C139,NP_RhoF)-F139*NP_PhiSh) | =IF(G139>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G139,NP_Rw,D139)),1) | =IF(AND(E139>0,F139<=NP_VshCut,G139>=NP_PhiCut),1,0) | =I139*(H139<=NP_SwCut) |
| 140 | 5104                                                                                                                                                                                                                                                          | 112.8                                                                                                                 | 2.473                                                                                                                                                                                                                                                                                                                                                                                                              | 2.28                                                                                                           | =IF(AND(A140>=NP_Top,A140<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B140,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C140,NP_RhoF)-F140*NP_PhiSh) | =IF(G140>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G140,NP_Rw,D140)),1) | =IF(AND(E140>0,F140<=NP_VshCut,G140>=NP_PhiCut),1,0) | =I140*(H140<=NP_SwCut) |
| 141 | 5106                                                                                                                                                                                                                                                          | 113.1                                                                                                                 | 2.485                                                                                                                                                                                                                                                                                                                                                                                                              | 2.52                                                                                                           | =IF(AND(A141>=NP_Top,A141<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B141,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C141,NP_RhoF)-F141*NP_PhiSh) | =IF(G141>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G141,NP_Rw,D141)),1) | =IF(AND(E141>0,F141<=NP_VshCut,G141>=NP_PhiCut),1,0) | =I141*(H141<=NP_SwCut) |
| 142 | 5108                                                                                                                                                                                                                                                          | 117                                                                                                                   | 2.475                                                                                                                                                                                                                                                                                                                                                                                                              | 2.4                                                                                                            | =IF(AND(A142>=NP_Top,A142<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B142,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C142,NP_RhoF)-F142*NP_PhiSh) | =IF(G142>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G142,NP_Rw,D142)),1) | =IF(AND(E142>0,F142<=NP_VshCut,G142>=NP_PhiCut),1,0) | =I142*(H142<=NP_SwCut) |
| 143 | 5110                                                                                                                                                                                                                                                          | 112.2                                                                                                                 | 2.482                                                                                                                                                                                                                                                                                                                                                                                                              | 2.51                                                                                                           | =IF(AND(A143>=NP_Top,A143<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B143,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C143,NP_RhoF)-F143*NP_PhiSh) | =IF(G143>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G143,NP_Rw,D143)),1) | =IF(AND(E143>0,F143<=NP_VshCut,G143>=NP_PhiCut),1,0) | =I143*(H143<=NP_SwCut) |
| 144 | 5112                                                                                                                                                                                                                                                          | 115.6                                                                                                                 | 2.477                                                                                                                                                                                                                                                                                                                                                                                                              | 2.27                                                                                                           | =IF(AND(A144>=NP_Top,A144<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B144,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C144,NP_RhoF)-F144*NP_PhiSh) | =IF(G144>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G144,NP_Rw,D144)),1) | =IF(AND(E144>0,F144<=NP_VshCut,G144>=NP_PhiCut),1,0) | =I144*(H144<=NP_SwCut) |
| 145 | 5114                                                                                                                                                                                                                                                          | 113.4                                                                                                                 | 2.485                                                                                                                                                                                                                                                                                                                                                                                                              | 2.69                                                                                                           | =IF(AND(A145>=NP_Top,A145<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B145,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C145,NP_RhoF)-F145*NP_PhiSh) | =IF(G145>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G145,NP_Rw,D145)),1) | =IF(AND(E145>0,F145<=NP_VshCut,G145>=NP_PhiCut),1,0) | =I145*(H145<=NP_SwCut) |
| 146 | 5116                                                                                                                                                                                                                                                          | 117.6                                                                                                                 | 2.475                                                                                                                                                                                                                                                                                                                                                                                                              | 2.27                                                                                                           | =IF(AND(A146>=NP_Top,A146<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B146,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C146,NP_RhoF)-F146*NP_PhiSh) | =IF(G146>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G146,NP_Rw,D146)),1) | =IF(AND(E146>0,F146<=NP_VshCut,G146>=NP_PhiCut),1,0) | =I146*(H146<=NP_SwCut) |
| 147 | 5118                                                                                                                                                                                                                                                          | 111.2                                                                                                                 | 2.483                                                                                                                                                                                                                                                                                                                                                                                                              | 2.5                                                                                                            | =IF(AND(A147>=NP_Top,A147<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B147,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C147,NP_RhoF)-F147*NP_PhiSh) | =IF(G147>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G147,NP_Rw,D147)),1) | =IF(AND(E147>0,F147<=NP_VshCut,G147>=NP_PhiCut),1,0) | =I147*(H147<=NP_SwCut) |
| 148 | 5120                                                                                                                                                                                                                                                          | 117.9                                                                                                                 | 2.482                                                                                                                                                                                                                                                                                                                                                                                                              | 2.38                                                                                                           | =IF(AND(A148>=NP_Top,A148<NP_Base),NP_Step,0)                                                                      | =MAX(0,MIN(1,PO.PP.Vsh.GammaRayIndex(B148,NP_GRcl,NP_GRsh)))                                                       | =MAX(0,PO.PP.Porosity.FromDensity(NP_RhoMa,C148,NP_RhoF)-F148*NP_PhiSh) | =IF(G148>0,MIN(1,PO.PP.Sw.Archie(NP_a,NP_m,NP_n,G148,NP_Rw,D148)),1) | =IF(AND(E148>0,F148<=NP_VshCut,G148>=NP_PhiCut),1,0) | =I148*(H148<=NP_SwCut) |

## Lambdas

| Name | RefersTo | Comment |
|------|----------|---------|
| PO.PP.Vsh.GammaRayIndex | =LAMBDA(GR, GR_cl, GR_sh, (GR-GR_cl)/(GR_sh-GR_cl)) | Linear gamma-ray shale index, IGR = (GR - GRclean) / (GRshale - GRclean). |
| PO.PP.Porosity.FromDensity | =LAMBDA(Rho_ma, Rho_b, Rho_f, (Rho_ma-Rho_b)/(Rho_ma-Rho_f)) | Porosity from a density log, (matrix density - bulk density) / (matrix density - fluid density). |
| PO.PP.Sw.Archie | =LAMBDA(a, m, n, Phi, Rw, Rt, ((a/Phi^m)*(Rw/Rt))^(1/n)) | Water saturation from the general Archie equation, Sw = ((a/phi^m)*(Rw/Rt))^(1/n). |
| PO.PP.Pay.NetPay | =LAMBDA(H, Vsh, PhiEff_frac, Sw, Vsh_cut, Phi_cut, Sw_cut, LET(res, (Vsh<=Vsh_cut)*(PhiEff_frac>=Phi_cut), pay, res*(Sw<=Sw_cut), gross, SUM(H), net, SUM(H*res), np, SUM(H*pay), hp, SUM(H*PhiEff_frac*pay), HSTACK(gross, net, np, net/gross, IF(np>0, hp/np, 0), IF(hp>0, SUM(H*PhiEff_frac*Sw*pay)/hp, 0)))) | Net reservoir and net pay over an interval from Vsh, porosity and Sw cut-offs: {gross, net reservoir, net pay, net-to-gross, pay porosity, pay Sw}. |
| PO.PP.Cutoff.PermFromCore | =LAMBDA(Phi_core, K_core, K_cut, LET(lk, LOG10(K_core), b, SLOPE(lk, Phi_core), (LOG10(K_cut)-INTERCEPT(lk, Phi_core))/b)) | Porosity cut-off at a permeability cut-off, from a least-squares fit of log10(k) on porosity to core points. |

## Names

| Name | RefersTo | Comment |
|------|----------|---------|
| NP_GRcl | $B$4 | Clean-sand gamma ray (Vsh = 0), API |
| NP_GRsh | $B$5 | Shale gamma ray (Vsh = 1), API |
| NP_RhoMa | $B$6 | Matrix density (sandstone), g/cm³ |
| NP_RhoF | $B$7 | Fluid density (fresh mud filtrate), g/cm³ |
| NP_RhoSh | $B$8 | Shale bulk density, for the shale correction, g/cm³ |
| NP_a | $B$9 | Tortuosity factor a |
| NP_m | $B$10 | Cementation exponent m |
| NP_n | $B$11 | Saturation exponent n |
| NP_Rw | $B$12 | Formation-water resistivity at formation temperature, ohm·m |
| NP_Top | $B$13 | Gross interval top (the oil sand's top), ft |
| NP_Base | $B$14 | Gross interval base (the water sand's base), ft |
| NP_VshCut | $B$15 | Shale-volume cutoff for reservoir, v/v |
| NP_PhiCut | $B$16 | Effective-porosity cutoff for reservoir, % |
| NP_SwCut | $B$17 | Water-saturation cutoff for pay, % |
| NP_KCut | $B$18 | Permeability cutoff, for the porosity cutoff from core, mD |
| NP_CutTol | $B$19 | Agreement limit of the porosity cutoff with core's, % |
| NP_SensMax | $B$20 | Largest net-pay change for a 2 p.u. step in the porosity cutoff, % |
| NP_Inputs | $B$4:$B$20 | The gamma-ray picks, the matrix, fluid and shale densities, Archie's a, m and n and Rw, the gross interval, the shale-volume, porosity and Sw cutoffs, the core permeability cutoff and the check limits |
| NP_Step | $B$25 | Log sample spacing, ft |
| NP_PhiSh | $B$26 | Shale's density porosity, the shale correction, % |
| NP_GVsh | $B$27 | Gross interval mean shale volume, v/v |
| NP_GPhi | $B$28 | Gross interval mean effective porosity, % |
| NP_GSw | $B$29 | Gross interval mean water saturation, % |
| NP_Gross | $B$30 | Gross thickness, ft |
| NP_Net | $B$31 | Net reservoir (Vsh and porosity cutoffs), ft |
| NP_Pay | $B$32 | Net pay (and the Sw cutoff), ft |
| NP_NTG | $B$33 | Net-to-gross, net reservoir over gross, % |
| NP_PayG | $B$34 | Pay over gross, % |
| NP_PayPhi | $B$35 | Pay's mean porosity, % |
| NP_PaySw | $B$36 | Pay's mean water saturation (pore-volume weighted), % |
| NP_HCPT | $B$37 | Hydrocarbon pore thickness of the pay, φ (1 − Sw) h, ft |
| NP_Plugs | $B$38 | Core plugs |
| NP_PhiCore | $B$39 | Porosity cutoff from core at the permeability cutoff, % |
| NP_PayCore | $B$40 | Net pay at core's porosity cutoff, ft |
| NP_Sens | $B$41 | Net-pay change per 2 p.u. of porosity cutoff, % |
| NP_PayCheck | $B$42 | Pay check verdict |
| NP_PayCheckNote | $C$42 | Pay check comment |
| NP_CoreCheck | $B$43 | Core cutoff check verdict |
| NP_CoreCheckNote | $C$43 | Core cutoff check comment |
| NP_SensCheck | $B$44 | Cutoff sensitivity check verdict |
| NP_SensCheckNote | $C$44 | Cutoff sensitivity check comment |
| NP_Results | $B$25:$B$44 | Sample spacing, shale porosity, the gross interval's mean Vsh, porosity and Sw, gross, net reservoir, net pay, net-to-gross, pay over gross, the pay's porosity, Sw and HC pore thickness, the core porosity cutoff and its net pay, sensitivity, three checks |
| NP_Curve | $A$51:$F$56 | Net pay for each porosity cutoff from 4 p.u. below to 6 p.u. above the input, at Sw cutoffs from 0.2 below to 0.2 above its input |
| NP_Core | $A$62:$C$76 | Each plug's core depth, helium porosity and air permeability |
| NP_OutPay | $B$80 | Net pay, third of the six |
| NP_OutNTG | $B$81 | Net-to-gross, fourth |
| NP_OutPhi | $B$82 | Pay's mean porosity, fifth |
| NP_OutSw | $B$83 | Pay's mean water saturation, sixth |
| NP_Log | $A$88:$J$148 | Each depth's GR, bulk density and deep resistivity, the thickness it stands for in the gross interval, its Vsh, effective porosity and Archie Sw, and whether it is reservoir and pay |

---

## Related Blueprints
- [Saturation-Height Function by Leverett J](/blueprint/po.pp.shf.fit.md)
- [Shaly-Sand Water Saturation](/blueprint/po.pp.sw.shaly.md)
- [Archie Water Saturation and Bulk Volume Water](/blueprint/po.pp.sw.archie.md)
- [Permeability from Logs](/blueprint/po.pp.permeability.estimate.md)
- [Shale Volume from Gamma Ray](/blueprint/po.pp.vshale.gr.md)
- [Formation Water Resistivity](/blueprint/po.pp.rw.determination.md)

