---
cid: po.bp.gl.unloading.design
hub: gl
tags: [gas-lift, unloading, valve-spacing, IPO, transfer-pressure, kill-fluid, design, artificial-lift]
facets: { discipline: production, phase: gas }
title: Gas-Lift Unloading Design
summary: "Places the unloading valves of a continuous gas-lift well and shows what each one sees as the kill fluid is unloaded."
slug: po.gl.unloading.design
type: worksheet
---

# Gas-Lift Unloading Design

## Description

Where do the unloading valves of a continuous gas-lift well go, and what does each one see as the well unloads its kill fluid? You enter the kickoff and operating injection pressures, the well and its kill fluid, the point of injection, a spacing factor and the valve's port and bellows. You read off each injection-pressure-operated (IPO) valve's depth, the transfer pressure there, its dome and test-rack setting, its closing pressure and spread, and the operating port.

**Parameters:**
- **Pressures**: surface kickoff and operating injection pressures and the drop per valve (`GLU_Pko`, `GLU_Pso`, `GLU_Drop`)
- **Well**: lift-gas gravity, wellhead pressure, kill-fluid gradient, surface and packer temperatures and the packer depth (`GLU_SG`, `GLU_Pwh`, `GLU_Gs`, `GLU_Ts`, `GLU_Tb`, `GLU_Dpk`)
- **From the injection-pressure sheet**: the point of injection, the tubing pressure there and the design gas rate (`GLU_Dpoi`, `GLU_Ptpoi`, `GLU_Qgi`)
- **Spacing**: the spacing factor (`GLU_Fs`, 20 %) and the least differential across a valve at transfer (`GLU_dPmin`, 100 psi)
- **Port and valve**: discharge coefficient, specific heat ratio, bellows area and spring tension (`GLU_Cd`, `GLU_k`, `GLU_Ab`, `GLU_St`) and the largest spread accepted (`GLU_SpreadMax`)
- **Overrides**: the casing gas gradient and R, each computed in the sheet until a measured value is typed over it (`GLU_Gg`, `GLU_R`)

**How to use it:** Type your kickoff and operating pressures, the kill fluid's gradient (0.052 psi/ft per ppg) and the point of injection and tubing pressure from your own Gas-Lift Injection Pressure and Point of Injection sheet. Type your valve's bellows area and port sizes from its catalogue. The spacing factor is a design choice: a larger one draws the transfer line nearer the casing, which spaces the valves closer and gives more of them, with a smaller differential at each. The table has ten mandrels; if the reach check fails, raise the kickoff pressure, lower the spacing factor or the drop per valve, or extend the table's formulas by a row per mandrel.

For each unloading valve the sheet gives its depth and temperature, its opening pressure at the surface and at depth, the transfer pressure there, the nitrogen dome it needs, and its closing pressure at depth and at the surface. It also gives the spread, the test-rack opening pressure at 60 °F, its closing margin at the operating pressure, the differential at transfer, and how far its surface closing pressure sits above the next valve's. The pressure-depth design chart draws the kickoff and operating casing lines, the transfer line, the flowing tubing line and the unloading zig-zag.

**Method:** The kickoff pressure U-tubes the kill fluid to the wellhead, which places the top valve. Each next mandrel sits where the kill fluid, standing on the transfer pressure at the valve above, meets that valve's own opening pressure. The transfer pressures lie on a design line drawn with a spacing factor: the wellhead pressure plus a share of the casing-to-wellhead difference at the surface, straight down to the flowing tubing pressure at the point of injection. The operating port is sized in the sheet by Thornhill-Craver.

- **Gas gradient.** The casing gas gradient Gg is the static gas-column gradient at the column's average temperature, in two passes as the valve-setting sheet takes it: at the operating pressure, then at the average pressure that first gradient gives to the point of injection. z is Dranchuk-Abou-Kassem at Standing's pseudo-criticals.
- **Kill fluid.** The kill fluid's gradient Gs is an input; the sheet shows its density, Gs/0.052 ppg.
- **Transfer line.** At the surface it starts at Ptr,0 = Pwh + Fs·(Pso − Pwh). It runs straight to the tubing pressure at the point of injection: Ptr(D) = Ptr,0 + (Ptpoi − Ptr,0)·D/Dpoi.
- **Spacing**, written in the sheet. The top valve sits where the kickoff casing pressure balances the kill fluid from the wellhead, D1 = (Pko − Pwh)/(Gs − Gg). Valve i opens at the surface at Psoi = Pko − i·ΔPdrop. Each next valve sits where its casing pressure meets the kill fluid standing on the transfer pressure at the valve above: Di = Di−1 + (Psoi + Gg·Di−1 − Ptr(Di−1))/(Gs − Gg). The first mandrel at or below the point of injection takes the operating orifice; the rows after it are not needed.
- **Port size**, written in the sheet. The Thornhill-Craver rate is linear in the port area, so the area the design rate needs is Qgi over the throughput of a 1 in² port, taken at the operating casing and tubing pressures of the point of injection. The smallest catalogue port that passes Qgi is the operating port, and its area over the bellows area is R. The unloading valves share it.
- **Settings of each unloading valve.** The opening pressure at depth is Pvo = Psoi + Gg·D. The dome that opens it against the transfer pressure there is Pd = (1 − R)·(Pvo − St) + R·Ptr. It closes at Pvc = Pd + St·(1 − R), its spread is Pvo − Pvc, and its surface closing pressure is Pvc − Gg·D. The test-rack opening pressure takes the dome to 60 °F with nitrogen's z, against one atmosphere on the tubing side.
- **Checks.**
  - Reach: a mandrel reaches the point of injection.
  - Port: the operating port passes the design rate.
  - Transfer: every unloading valve opens at least ΔPmin over its transfer pressure, so gas still passes as it takes over.
  - Closing sequence: each valve's surface closing pressure is above the next one's, so the upper valve closes once the next takes the gas.
  - Closing: every unloading valve closes at the operating casing pressure, so only the orifice injects once the well is unloaded.
  - Spread: the largest spread is within the limit.

**Example:** The well is GL-1, the one the Gas-Lift Injection Pressure and Point of Injection, Gas-Lift Valve Setting and Gas-Lift Valve Throughput sheets use: 0.65-gravity lift gas, 120 psia at the wellhead, 80 °F at surface and 200 °F at the packer at 8,000 ft, and 500 Mscf/d of design gas. Its point of injection (7,154 ft) and the flowing tubing pressure there (1,080.5 psia) are typed in from the injection-pressure sheet. Kickoff is at 1,200 psia with a 0.465 psi/ft kill fluid, the surface opening pressure drops 25 psi per valve, and the well then operates at 1,000 psia. The spacing factor is 20 %.

The gas gradient is 0.0253 psi/ft, and the 500 Mscf/d design takes a 16/64-in port, R = 0.0638, as the valve-setting sheet finds. The kill fluid is 8.94 ppg. The transfer line starts at 120 + 0.2 × 880 = 296 psia and runs at 0.1097 psi/ft to 1,080.5 psia at the point of injection. Six unloading valves reach it, at 2,456, 3,927, 5,059, 5,917, 6,554 and 7,011 ft, and the orifice sits at 7,154 ft. The top valve, at 117 °F, opens at 1,237.1 psia against a 565.3 psia transfer pressure. Its dome holds 1,194.3 psia at depth, it closes there with a 43 psi spread, and it sets at 1,130.3 psia on the test rack. The test-rack settings fall to 1,017.6 psia at valve 6. Every valve opens at least 163 psi over its transfer pressure. The surface closing pressures fall from 1,132.2 to 1,039.6 psia, by at least 15 psi from each valve to the next. The closest valve (6) closes 40 psi above the operating casing pressure. The design reaches the point of injection, the port passes the design rate, and the valves transfer, close in turn and close at the operating pressure within the spread limit. With no spacing factor the transfer line is the valve-setting sheet's straight design tubing line, and the sheet gives that sheet's five valves, at 2,456, 4,190, 5,437, 6,319 and 6,925 ft; the 20 % factor adds a sixth. At a 1,100 psia kickoff the ten mandrels bunch up near 6,600 ft and never reach the point of injection: the reach and closing checks fail.

The sheet was checked against Guo, Lyons and Ghalambor (2007) Example Problem 13.7, whose top valve, at 2,347 ft and 126 °F with R = 0.2562 and no spring, is designed to open at 953 psia against 424 psia tubing, which needs an 817 psia dome that closes at 817 psia. To check it, put the sheet's top valve there, as on the valve-setting sheet: no spacing factor, R typed over as 0.2562, a zero gas gradient and drop, a 953 psia kickoff, a flat 424 psia tubing line, both temperatures at 126 °F, and the kill-fluid gradient that puts valve 1 at 2,347 ft (529/2,347 = 0.225394 psi/ft). The sheet returns the printed 817 psia dome and closing pressure and the 135 psi spread.

## Validity

Unbalanced IPO bellows valves with a nitrogen dome, set on a test rack at 60 °F, and an orifice at the point of injection, in a vertical well unloaded down the casing annulus. The spacing assumes a constant gas gradient and a straight transfer line; a flowing-gradient survey's curve moves the deeper mandrels by tens of feet. The kill fluid is a single gradient standing in the tubing: a well with oil and water above the kill fluid unloads differently. The unloading valves share the operating port, so they share one R. Each valve's temperature is the static geotherm at its depth; a flowing well runs warmer and sets its domes a little higher. The drop per valve is a fixed surface-pressure step, so the closing-sequence check, not the step, is what proves the valves close in turn.

The 20 % spacing factor is the rule of thumb usually quoted for the surface point of the design (transfer) line, after Winkler and Smith. That book and API RP 11V6 were not to hand, so 20 % is a design input here, not a value taken from them; the sheet's numbers are checked against the valve-setting sheet and an independent calculation instead.

Named alternatives: the Gas-Lift Valve Setting sheet's design on the straight tubing line (this sheet with a zero spacing factor); a percentage-load or gradient spacing factor in psi/ft, as Brown's charts give by rate and tubing size; production-pressure-operated (PPO) valves, set against the tubing; and the Gas-Lift Injection Pressure and Point of Injection sheet for the point of injection itself.

## References

- Winkler, H.W. and Smith, S.S. (1962). *Camco Gas Lift Manual*. Camco Inc., Houston (the IPO design with a transfer line; not to hand).
- Brown, K.E. (1980). *The Technology of Artificial Lift Methods*, Vol. 2a. PennWell (continuous-flow unloading design and spacing factors; not to hand).
- API RP 11V6 (2008). *Recommended Practice for Design of Continuous Flow Gas Lift Installations Using Injection Pressure Operated Valves* (not to hand).
- Guo, B., Lyons, W.C. and Ghalambor, A. (2007). *Petroleum Production Engineering: A Computer-Assisted Approach*. Gulf Professional Publishing, Ch. 13 (gas lift), Eqs. 13.42, 13.43, 13.57 and 13.58, Example Problem 13.7.
- Takacs, G. (2005). *Gas Lift Manual*. PennWell, Ch. 6 (unloading valve string design).

## Functions used

`PO.GL.Inj.Grad`, `PO.PVT.Z.ByDAK`, `PO.PVT.Ppc.ByStanding`, `PO.PVT.Tpc.ByStanding`, `PO.GL.Valve.ThornhillCraver`, `PO.GL.Valve.Pd.Required`, `PO.GL.Valve.Pvc`, `PO.GL.Valve.Spread`, `PO.GL.Valve.TRO`

## Spreadsheet: GlUnloadingDesign

|     | A                                                                                                                                                                                                         | B                                                                                                                                               | C                                                                                                                                                                                                                                                                                                                                     | D                                   | E                                                                                        | F                                        | G                                           | H                                                                       | I                                                           | J                                                     | K                                        | L                                                               | M                                                  | N                                 | O                                                       |
|-----|-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|-------------------------------------------------------------------------------------------------------------------------------------------------|---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|-------------------------------------|------------------------------------------------------------------------------------------|------------------------------------------|---------------------------------------------|-------------------------------------------------------------------------|-------------------------------------------------------------|-------------------------------------------------------|------------------------------------------|-----------------------------------------------------------------|----------------------------------------------------|-----------------------------------|---------------------------------------------------------|
| 1   | Gas-Lift Unloading Design                                                                                                                                                                                 |                                                                                                                                                 | Petroleum Office                                                                                                                                                                                                                                                                                                                      |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 2   | Blue cells on yellow are inputs. Type the kickoff and operating pressures, the kill fluid and the spacing factor; the mandrels, transfer pressures and valve settings follow.                             |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 4   | Well GL-1, Kickoff and Kill Fluid                                                                                                                                                                         |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 5   | Surface kickoff pressure                                                                                                                                                                                  | 1200                                                                                                                                            | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 6   | Surface operating injection pressure                                                                                                                                                                      | 1000                                                                                                                                            | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 7   | Surface opening pressure drop per valve                                                                                                                                                                   | 25                                                                                                                                              | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 8   | Lift-gas specific gravity                                                                                                                                                                                 | 0.65                                                                                                                                            | air = 1                                                                                                                                                                                                                                                                                                                               |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 9   | Flowing wellhead pressure                                                                                                                                                                                 | 120                                                                                                                                             | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 10  | Kill-fluid gradient                                                                                                                                                                                       | 0.465                                                                                                                                           | psi/ft                                                                                                                                                                                                                                                                                                                                |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 11  | Surface temperature                                                                                                                                                                                       | 80                                                                                                                                              | °F                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 12  | Temperature at the packer depth                                                                                                                                                                           | 200                                                                                                                                             | °F                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 13  | Packer depth                                                                                                                                                                                              | 8000                                                                                                                                            | ft                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 14  | Point of injection (gl.injection.pressure)                                                                                                                                                                | 7154                                                                                                                                            | ft                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 15  | Tubing pressure at the point of injection                                                                                                                                                                 | 1080.5                                                                                                                                          | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 16  | Design injection gas rate                                                                                                                                                                                 | 500                                                                                                                                             | Mscf/d                                                                                                                                                                                                                                                                                                                                |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 17  | Spacing Factor and Transfer                                                                                                                                                                               |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 18  | Spacing factor, share of Pso − Pwh added at the surface                                                                                                                                                   | 0.2                                                                                                                                             | %                                                                                                                                                                                                                                                                                                                                     |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 19  | Least differential across a valve at transfer                                                                                                                                                             | 100                                                                                                                                             | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 20  | Valve and Port                                                                                                                                                                                            |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 21  | Port discharge coefficient                                                                                                                                                                                | 0.6                                                                                                                                             | —                                                                                                                                                                                                                                                                                                                                     |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 22  | Lift-gas specific heat ratio, Cp/Cv                                                                                                                                                                       | 1.28                                                                                                                                            | —                                                                                                                                                                                                                                                                                                                                     |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 23  | Valve bellows area                                                                                                                                                                                        | 0.77                                                                                                                                            | in²                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 24  | Spring tension as a pressure (0: none)                                                                                                                                                                    | 0                                                                                                                                               | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 25  | Largest valve spread accepted                                                                                                                                                                             | 100                                                                                                                                             | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 26  | Casing gas gradient (type over to override)                                                                                                                                                               | =GLU_GgCalc                                                                                                                                     | psi/ft                                                                                                                                                                                                                                                                                                                                |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 27  | Port-to-bellows ratio R (type over to override)                                                                                                                                                           | =GLU_Rport                                                                                                                                      | —                                                                                                                                                                                                                                                                                                                                     |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 29  | Constants                                                                                                                                                                                                 |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 30  | Rankine at 0 °F                                                                                                                                                                                           | 459.67                                                                                                                                          | °R                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 31  | Test-rack temperature                                                                                                                                                                                     | 60                                                                                                                                              | °F                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 32  | Gradient of a 1 ppg fluid                                                                                                                                                                                 | 0.052                                                                                                                                           | psi/ft per ppg                                                                                                                                                                                                                                                                                                                        |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 34  | Operating Port (GL.Design.PortSize, in the Sheet)                                                                                                                                                         |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 35  | Each port's Thornhill-Craver capacity at the operating casing and tubing pressures of the point of injection; the smallest that passes the design rate is chosen.                                         |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 36  | Port (1/64 in)                                                                                                                                                                                            | Port diameter (in)                                                                                                                              | Port area (in²)                                                                                                                                                                                                                                                                                                                       | Ap/Ab, R                            | Capacity (Mscf/d)                                                                        |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 37  | 8                                                                                                                                                                                                         | =A37/64                                                                                                                                         | =PI()*(B37/2)^2                                                                                                                                                                                                                                                                                                                       | =C37/GLU_Ab                         | =PO.GL.Valve.ThornhillCraver(GLU_Cd,C37,GLU_P1op,GLU_Ptpoi,GLU_SG,GLU_TPOI+GLU_R0,GLU_k) |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 38  | 12                                                                                                                                                                                                        | =A38/64                                                                                                                                         | =PI()*(B38/2)^2                                                                                                                                                                                                                                                                                                                       | =C38/GLU_Ab                         | =PO.GL.Valve.ThornhillCraver(GLU_Cd,C38,GLU_P1op,GLU_Ptpoi,GLU_SG,GLU_TPOI+GLU_R0,GLU_k) |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 39  | 16                                                                                                                                                                                                        | =A39/64                                                                                                                                         | =PI()*(B39/2)^2                                                                                                                                                                                                                                                                                                                       | =C39/GLU_Ab                         | =PO.GL.Valve.ThornhillCraver(GLU_Cd,C39,GLU_P1op,GLU_Ptpoi,GLU_SG,GLU_TPOI+GLU_R0,GLU_k) |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 40  | 20                                                                                                                                                                                                        | =A40/64                                                                                                                                         | =PI()*(B40/2)^2                                                                                                                                                                                                                                                                                                                       | =C40/GLU_Ab                         | =PO.GL.Valve.ThornhillCraver(GLU_Cd,C40,GLU_P1op,GLU_Ptpoi,GLU_SG,GLU_TPOI+GLU_R0,GLU_k) |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 41  | 24                                                                                                                                                                                                        | =A41/64                                                                                                                                         | =PI()*(B41/2)^2                                                                                                                                                                                                                                                                                                                       | =C41/GLU_Ab                         | =PO.GL.Valve.ThornhillCraver(GLU_Cd,C41,GLU_P1op,GLU_Ptpoi,GLU_SG,GLU_TPOI+GLU_R0,GLU_k) |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 42  | 28                                                                                                                                                                                                        | =A42/64                                                                                                                                         | =PI()*(B42/2)^2                                                                                                                                                                                                                                                                                                                       | =C42/GLU_Ab                         | =PO.GL.Valve.ThornhillCraver(GLU_Cd,C42,GLU_P1op,GLU_Ptpoi,GLU_SG,GLU_TPOI+GLU_R0,GLU_k) |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 43  | 32                                                                                                                                                                                                        | =A43/64                                                                                                                                         | =PI()*(B43/2)^2                                                                                                                                                                                                                                                                                                                       | =C43/GLU_Ab                         | =PO.GL.Valve.ThornhillCraver(GLU_Cd,C43,GLU_P1op,GLU_Ptpoi,GLU_SG,GLU_TPOI+GLU_R0,GLU_k) |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 46  | Unloading Valves (GL.Design.Spacing, in the Sheet)                                                                                                                                                        |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 47  | Valve 1 sits where the kickoff pressure U-tubes the kill fluid to the wellhead; each next valve where its own opening pressure meets the kill fluid standing on the transfer pressure at the valve above. |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 48  | The transfer line runs from the wellhead pressure plus the spacing factor's share of Pso − Pwh at the surface to the tubing pressure at the point of injection.                                           |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 49  | How to use it: type your kickoff, operating and kill-fluid values and your point of injection; when the reach check fails, raise the kickoff pressure or lower the spacing factor.                        |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 50  | Valve                                                                                                                                                                                                     | Role                                                                                                                                            | Depth (ft)                                                                                                                                                                                                                                                                                                                            | Temperature (°F)                    | Surface opening (psi)                                                                    | Opening at depth (psi)                   | Transfer (psi)                              | Dome at depth (psi)                                                     | Closing (psi)                                               | Spread (psi)                                          | Surface closing (psi)                    | Test-rack opening (psi)                                         | Closing margin (psi)                               | Transfer differential (psi)       | Closes before next (psi)                                |
| 51  | 1                                                                                                                                                                                                         | =IF(C51>=GLU_Dpoi,"operating","unloading")                                                                                                      | =MIN((GLU_Pko-GLU_Pwh)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                                      | =GLU_Ts+(GLU_Tb-GLU_Ts)*C51/GLU_Dpk | =GLU_Pko-A51*GLU_Drop                                                                    | =IF($B51="unloading",E51+GLU_Gg*C51,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C51/GLU_Dpoi | =IF($B51="unloading",PO.GL.Valve.Pd.Required(F51,GLU_R,G51,GLU_St),"—") | =IF($B51="unloading",PO.GL.Valve.Pvc(H51,GLU_R,GLU_St),"—") | =IF($B51="unloading",PO.GL.Valve.Spread(F51,I51),"—") | =IF($B51="unloading",I51-GLU_Gg*C51,"—") | =IF($B51="unloading",PO.GL.Valve.TRO(H51,D51,GLU_R,GLU_St),"—") | =IF($B51="unloading",I51-(GLU_Pso+GLU_Gg*C51),"—") | =IF($B51="unloading",F51-G51,"—") | =IF(AND($B51="unloading",$B52="unloading"),K51-K52,"—") |
| 52  | 2                                                                                                                                                                                                         | =IF(C52<GLU_Dpoi,"unloading",IF(C51<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C51+(E52+GLU_Gg*C51-G51)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C52/GLU_Dpk | =GLU_Pko-A52*GLU_Drop                                                                    | =IF($B52="unloading",E52+GLU_Gg*C52,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C52/GLU_Dpoi | =IF($B52="unloading",PO.GL.Valve.Pd.Required(F52,GLU_R,G52,GLU_St),"—") | =IF($B52="unloading",PO.GL.Valve.Pvc(H52,GLU_R,GLU_St),"—") | =IF($B52="unloading",PO.GL.Valve.Spread(F52,I52),"—") | =IF($B52="unloading",I52-GLU_Gg*C52,"—") | =IF($B52="unloading",PO.GL.Valve.TRO(H52,D52,GLU_R,GLU_St),"—") | =IF($B52="unloading",I52-(GLU_Pso+GLU_Gg*C52),"—") | =IF($B52="unloading",F52-G52,"—") | =IF(AND($B52="unloading",$B53="unloading"),K52-K53,"—") |
| 53  | 3                                                                                                                                                                                                         | =IF(C53<GLU_Dpoi,"unloading",IF(C52<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C52+(E53+GLU_Gg*C52-G52)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C53/GLU_Dpk | =GLU_Pko-A53*GLU_Drop                                                                    | =IF($B53="unloading",E53+GLU_Gg*C53,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C53/GLU_Dpoi | =IF($B53="unloading",PO.GL.Valve.Pd.Required(F53,GLU_R,G53,GLU_St),"—") | =IF($B53="unloading",PO.GL.Valve.Pvc(H53,GLU_R,GLU_St),"—") | =IF($B53="unloading",PO.GL.Valve.Spread(F53,I53),"—") | =IF($B53="unloading",I53-GLU_Gg*C53,"—") | =IF($B53="unloading",PO.GL.Valve.TRO(H53,D53,GLU_R,GLU_St),"—") | =IF($B53="unloading",I53-(GLU_Pso+GLU_Gg*C53),"—") | =IF($B53="unloading",F53-G53,"—") | =IF(AND($B53="unloading",$B54="unloading"),K53-K54,"—") |
| 54  | 4                                                                                                                                                                                                         | =IF(C54<GLU_Dpoi,"unloading",IF(C53<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C53+(E54+GLU_Gg*C53-G53)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C54/GLU_Dpk | =GLU_Pko-A54*GLU_Drop                                                                    | =IF($B54="unloading",E54+GLU_Gg*C54,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C54/GLU_Dpoi | =IF($B54="unloading",PO.GL.Valve.Pd.Required(F54,GLU_R,G54,GLU_St),"—") | =IF($B54="unloading",PO.GL.Valve.Pvc(H54,GLU_R,GLU_St),"—") | =IF($B54="unloading",PO.GL.Valve.Spread(F54,I54),"—") | =IF($B54="unloading",I54-GLU_Gg*C54,"—") | =IF($B54="unloading",PO.GL.Valve.TRO(H54,D54,GLU_R,GLU_St),"—") | =IF($B54="unloading",I54-(GLU_Pso+GLU_Gg*C54),"—") | =IF($B54="unloading",F54-G54,"—") | =IF(AND($B54="unloading",$B55="unloading"),K54-K55,"—") |
| 55  | 5                                                                                                                                                                                                         | =IF(C55<GLU_Dpoi,"unloading",IF(C54<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C54+(E55+GLU_Gg*C54-G54)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C55/GLU_Dpk | =GLU_Pko-A55*GLU_Drop                                                                    | =IF($B55="unloading",E55+GLU_Gg*C55,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C55/GLU_Dpoi | =IF($B55="unloading",PO.GL.Valve.Pd.Required(F55,GLU_R,G55,GLU_St),"—") | =IF($B55="unloading",PO.GL.Valve.Pvc(H55,GLU_R,GLU_St),"—") | =IF($B55="unloading",PO.GL.Valve.Spread(F55,I55),"—") | =IF($B55="unloading",I55-GLU_Gg*C55,"—") | =IF($B55="unloading",PO.GL.Valve.TRO(H55,D55,GLU_R,GLU_St),"—") | =IF($B55="unloading",I55-(GLU_Pso+GLU_Gg*C55),"—") | =IF($B55="unloading",F55-G55,"—") | =IF(AND($B55="unloading",$B56="unloading"),K55-K56,"—") |
| 56  | 6                                                                                                                                                                                                         | =IF(C56<GLU_Dpoi,"unloading",IF(C55<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C55+(E56+GLU_Gg*C55-G55)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C56/GLU_Dpk | =GLU_Pko-A56*GLU_Drop                                                                    | =IF($B56="unloading",E56+GLU_Gg*C56,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C56/GLU_Dpoi | =IF($B56="unloading",PO.GL.Valve.Pd.Required(F56,GLU_R,G56,GLU_St),"—") | =IF($B56="unloading",PO.GL.Valve.Pvc(H56,GLU_R,GLU_St),"—") | =IF($B56="unloading",PO.GL.Valve.Spread(F56,I56),"—") | =IF($B56="unloading",I56-GLU_Gg*C56,"—") | =IF($B56="unloading",PO.GL.Valve.TRO(H56,D56,GLU_R,GLU_St),"—") | =IF($B56="unloading",I56-(GLU_Pso+GLU_Gg*C56),"—") | =IF($B56="unloading",F56-G56,"—") | =IF(AND($B56="unloading",$B57="unloading"),K56-K57,"—") |
| 57  | 7                                                                                                                                                                                                         | =IF(C57<GLU_Dpoi,"unloading",IF(C56<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C56+(E57+GLU_Gg*C56-G56)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C57/GLU_Dpk | =GLU_Pko-A57*GLU_Drop                                                                    | =IF($B57="unloading",E57+GLU_Gg*C57,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C57/GLU_Dpoi | =IF($B57="unloading",PO.GL.Valve.Pd.Required(F57,GLU_R,G57,GLU_St),"—") | =IF($B57="unloading",PO.GL.Valve.Pvc(H57,GLU_R,GLU_St),"—") | =IF($B57="unloading",PO.GL.Valve.Spread(F57,I57),"—") | =IF($B57="unloading",I57-GLU_Gg*C57,"—") | =IF($B57="unloading",PO.GL.Valve.TRO(H57,D57,GLU_R,GLU_St),"—") | =IF($B57="unloading",I57-(GLU_Pso+GLU_Gg*C57),"—") | =IF($B57="unloading",F57-G57,"—") | =IF(AND($B57="unloading",$B58="unloading"),K57-K58,"—") |
| 58  | 8                                                                                                                                                                                                         | =IF(C58<GLU_Dpoi,"unloading",IF(C57<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C57+(E58+GLU_Gg*C57-G57)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C58/GLU_Dpk | =GLU_Pko-A58*GLU_Drop                                                                    | =IF($B58="unloading",E58+GLU_Gg*C58,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C58/GLU_Dpoi | =IF($B58="unloading",PO.GL.Valve.Pd.Required(F58,GLU_R,G58,GLU_St),"—") | =IF($B58="unloading",PO.GL.Valve.Pvc(H58,GLU_R,GLU_St),"—") | =IF($B58="unloading",PO.GL.Valve.Spread(F58,I58),"—") | =IF($B58="unloading",I58-GLU_Gg*C58,"—") | =IF($B58="unloading",PO.GL.Valve.TRO(H58,D58,GLU_R,GLU_St),"—") | =IF($B58="unloading",I58-(GLU_Pso+GLU_Gg*C58),"—") | =IF($B58="unloading",F58-G58,"—") | =IF(AND($B58="unloading",$B59="unloading"),K58-K59,"—") |
| 59  | 9                                                                                                                                                                                                         | =IF(C59<GLU_Dpoi,"unloading",IF(C58<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C58+(E59+GLU_Gg*C58-G58)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C59/GLU_Dpk | =GLU_Pko-A59*GLU_Drop                                                                    | =IF($B59="unloading",E59+GLU_Gg*C59,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C59/GLU_Dpoi | =IF($B59="unloading",PO.GL.Valve.Pd.Required(F59,GLU_R,G59,GLU_St),"—") | =IF($B59="unloading",PO.GL.Valve.Pvc(H59,GLU_R,GLU_St),"—") | =IF($B59="unloading",PO.GL.Valve.Spread(F59,I59),"—") | =IF($B59="unloading",I59-GLU_Gg*C59,"—") | =IF($B59="unloading",PO.GL.Valve.TRO(H59,D59,GLU_R,GLU_St),"—") | =IF($B59="unloading",I59-(GLU_Pso+GLU_Gg*C59),"—") | =IF($B59="unloading",F59-G59,"—") | =IF(AND($B59="unloading",$B60="unloading"),K59-K60,"—") |
| 60  | 10                                                                                                                                                                                                        | =IF(C60<GLU_Dpoi,"unloading",IF(C59<GLU_Dpoi,"operating","not needed"))                                                                         | =MIN(C59+(E60+GLU_Gg*C59-G59)/(GLU_Gs-GLU_Gg),GLU_Dpoi)                                                                                                                                                                                                                                                                               | =GLU_Ts+(GLU_Tb-GLU_Ts)*C60/GLU_Dpk | =GLU_Pko-A60*GLU_Drop                                                                    | =IF($B60="unloading",E60+GLU_Gg*C60,"—") | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*C60/GLU_Dpoi | =IF($B60="unloading",PO.GL.Valve.Pd.Required(F60,GLU_R,G60,GLU_St),"—") | =IF($B60="unloading",PO.GL.Valve.Pvc(H60,GLU_R,GLU_St),"—") | =IF($B60="unloading",PO.GL.Valve.Spread(F60,I60),"—") | =IF($B60="unloading",I60-GLU_Gg*C60,"—") | =IF($B60="unloading",PO.GL.Valve.TRO(H60,D60,GLU_R,GLU_St),"—") | =IF($B60="unloading",I60-(GLU_Pso+GLU_Gg*C60),"—") | =IF($B60="unloading",F60-G60,"—") | —                                                       |
| 62  | Design Lines                                                                                                                                                                                              |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 63  | Depth (ft)                                                                                                                                                                                                | Unloading (psi)                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       | Depth (ft)                          | Kickoff casing (psi)                                                                     | Operating casing (psi)                   | Transfer line (psi)                         | Flowing tubing (psi)                                                    |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 64  | 0                                                                                                                                                                                                         | =GLU_Pwh                                                                                                                                        |                                                                                                                                                                                                                                                                                                                                       | 0                                   | =GLU_Pko+GLU_Gg*D64                                                                      | =GLU_Pso+GLU_Gg*D64                      | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*D64/GLU_Dpoi | =GLU_Pwh+(GLU_Ptpoi-GLU_Pwh)*D64/GLU_Dpoi                               |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 65  | =C51                                                                                                                                                                                                      | =GLU_Pwh+GLU_Gs*C51                                                                                                                             |                                                                                                                                                                                                                                                                                                                                       | =GLU_Dpoi                           | =GLU_Pko+GLU_Gg*D65                                                                      | =GLU_Pso+GLU_Gg*D65                      | =GLU_Ptr0+(GLU_Ptpoi-GLU_Ptr0)*D65/GLU_Dpoi | =GLU_Pwh+(GLU_Ptpoi-GLU_Pwh)*D65/GLU_Dpoi                               |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 66  | =C51                                                                                                                                                                                                      | =G51                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 67  | =C52                                                                                                                                                                                                      | =G51+GLU_Gs*(C52-C51)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 68  | =C52                                                                                                                                                                                                      | =G52                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 69  | =C53                                                                                                                                                                                                      | =G52+GLU_Gs*(C53-C52)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 70  | =C53                                                                                                                                                                                                      | =G53                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 71  | =C54                                                                                                                                                                                                      | =G53+GLU_Gs*(C54-C53)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 72  | =C54                                                                                                                                                                                                      | =G54                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 73  | =C55                                                                                                                                                                                                      | =G54+GLU_Gs*(C55-C54)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 74  | =C55                                                                                                                                                                                                      | =G55                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 75  | =C56                                                                                                                                                                                                      | =G55+GLU_Gs*(C56-C55)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 76  | =C56                                                                                                                                                                                                      | =G56                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 77  | =C57                                                                                                                                                                                                      | =G56+GLU_Gs*(C57-C56)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 78  | =C57                                                                                                                                                                                                      | =G57                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 79  | =C58                                                                                                                                                                                                      | =G57+GLU_Gs*(C58-C57)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 80  | =C58                                                                                                                                                                                                      | =G58                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 81  | =C59                                                                                                                                                                                                      | =G58+GLU_Gs*(C59-C58)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 82  | =C59                                                                                                                                                                                                      | =G59                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 83  | =C60                                                                                                                                                                                                      | =G59+GLU_Gs*(C60-C59)                                                                                                                           |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 84  | =C60                                                                                                                                                                                                      | =G60                                                                                                                                            |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 86  | Gas Gradient, Kill Fluid and Port                                                                                                                                                                         |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 87  | Pseudo-critical temperature (Standing)                                                                                                                                                                    | =PO.PVT.Tpc.ByStanding(GLU_SG)                                                                                                                  | °R                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 88  | Pseudo-critical pressure (Standing)                                                                                                                                                                       | =PO.PVT.Ppc.ByStanding(GLU_SG)                                                                                                                  | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 89  | Temperature at the point of injection                                                                                                                                                                     | =GLU_Ts+(GLU_Tb-GLU_Ts)*GLU_Dpoi/GLU_Dpk                                                                                                        | °F                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 90  | Gas-column average temperature                                                                                                                                                                            | =(GLU_Ts+GLU_TPOI)/2                                                                                                                            | °F                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 91  | Gas gradient, first pass                                                                                                                                                                                  | =PO.GL.Inj.Grad(GLU_SG,GLU_Pso,GLU_Tcol+GLU_R0,PO.PVT.Z.ByDAK(GLU_Pso/GLU_Ppc,(GLU_Tcol+GLU_R0)/GLU_Tpc))                                       | psi/ft                                                                                                                                                                                                                                                                                                                                |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 92  | Gas gradient at the average pressure                                                                                                                                                                      | =PO.GL.Inj.Grad(GLU_SG,GLU_Pso+GLU_G1*GLU_Dpoi/2,GLU_Tcol+GLU_R0,PO.PVT.Z.ByDAK((GLU_Pso+GLU_G1*GLU_Dpoi/2)/GLU_Ppc,(GLU_Tcol+GLU_R0)/GLU_Tpc)) | psi/ft                                                                                                                                                                                                                                                                                                                                |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 93  | Kill-fluid density for its gradient                                                                                                                                                                       | =GLU_Gs/GLU_PsiPpg                                                                                                                              | ppg                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 94  | Operating casing pressure at injection depth                                                                                                                                                              | =GLU_Pso+GLU_Gg*GLU_Dpoi                                                                                                                        | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 95  | Port area the design rate needs                                                                                                                                                                           | =GLU_Qgi/PO.GL.Valve.ThornhillCraver(GLU_Cd,1,GLU_P1op,GLU_Ptpoi,GLU_SG,GLU_TPOI+GLU_R0,GLU_k)                                                  | in²                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 96  | Ports too small for the design rate                                                                                                                                                                       | =COUNTIF($E$37:$E$43,"<"&GLU_Qgi)                                                                                                               | —                                                                                                                                                                                                                                                                                                                                     |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 97  | Operating port                                                                                                                                                                                            | =INDEX($A$37:$A$43,MIN(GLU_Small+1,ROWS($E$37:$E$43)))                                                                                          | 1/64 in                                                                                                                                                                                                                                                                                                                               |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 98  | Operating port area                                                                                                                                                                                       | =INDEX($C$37:$C$43,MIN(GLU_Small+1,ROWS($E$37:$E$43)))                                                                                          | in²                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 99  | R of the operating port                                                                                                                                                                                   | =GLU_Ap/GLU_Ab                                                                                                                                  | —                                                                                                                                                                                                                                                                                                                                     |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 100 | Gas the operating port passes                                                                                                                                                                             | =INDEX($E$37:$E$43,MIN(GLU_Small+1,ROWS($E$37:$E$43)))                                                                                          | Mscf/d                                                                                                                                                                                                                                                                                                                                |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 101 | Unloading                                                                                                                                                                                                 |                                                                                                                                                 |                                                                                                                                                                                                                                                                                                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 102 | Transfer line at the surface, Pwh + Fs·(Pso − Pwh)                                                                                                                                                        | =GLU_Pwh+GLU_Fs*(GLU_Pso-GLU_Pwh)                                                                                                               | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 103 | Transfer line's gradient to the point of injection                                                                                                                                                        | =(GLU_Ptpoi-GLU_Ptr0)/GLU_Dpoi                                                                                                                  | psi/ft                                                                                                                                                                                                                                                                                                                                |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 104 | Unloading valves                                                                                                                                                                                          | =COUNTIF($B$51:$B$60,"unloading")                                                                                                               | —                                                                                                                                                                                                                                                                                                                                     |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 105 | Deepest mandrel                                                                                                                                                                                           | =MAX($C$51:$C$60)                                                                                                                               | ft                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 106 | Top valve depth                                                                                                                                                                                           | =C51                                                                                                                                            | ft                                                                                                                                                                                                                                                                                                                                    |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 107 | Top valve opening pressure at depth                                                                                                                                                                       | =F51                                                                                                                                            | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 108 | Top valve dome pressure at depth                                                                                                                                                                          | =H51                                                                                                                                            | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 109 | Top valve closing pressure                                                                                                                                                                                | =I51                                                                                                                                            | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 110 | Top valve spread                                                                                                                                                                                          | =J51                                                                                                                                            | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 111 | Top valve test-rack opening at 60 °F                                                                                                                                                                      | =L51                                                                                                                                            | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 112 | Smallest closing margin at the operating pressure                                                                                                                                                         | =MIN($M$51:$M$60)                                                                                                                               | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 113 | Largest valve spread                                                                                                                                                                                      | =MAX($J$51:$J$60)                                                                                                                               | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 114 | Smallest transfer differential                                                                                                                                                                            | =MIN($N$51:$N$60)                                                                                                                               | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 115 | Smallest fall in surface closing pressure, valve to valve                                                                                                                                                 | =IF(COUNT($O$51:$O$60)=0,0,MIN($O$51:$O$60))                                                                                                    | psi                                                                                                                                                                                                                                                                                                                                   |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 116 | Reach check                                                                                                                                                                                               | =IF(COUNTIF($B$51:$B$60,"operating")=1,"PASS","FAIL")                                                                                           | =IF(COUNTIF($B$51:$B$60,"operating")=1,""&GLU_Nu&" unloading valves reach the point of injection; the operating orifice sits at "&FIXED(GLU_Dpoi,0)&" ft","10 mandrels reach only "&FIXED(GLU_Dlast,0)&" ft, above the point of injection: raise the kickoff pressure, lower the spacing factor or add mandrels")                     |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 117 | Port check                                                                                                                                                                                                | =IF(GLU_Qport>=GLU_Qgi,"PASS","FAIL")                                                                                                           | =IF(GLU_Qport>=GLU_Qgi,"a "&GLU_Port&"/64-in port passes "&FIXED(GLU_Qport,0)&" Mscf/d against the design "&FIXED(GLU_Qgi,0)&" Mscf/d","even a "&GLU_Port&"/64-in port passes only "&FIXED(GLU_Qport,0)&" Mscf/d: raise the differential or run two orifices")                                                                        |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 118 | Transfer check                                                                                                                                                                                            | =IF(GLU_DiffMin>=GLU_dPmin,"PASS","WARN")                                                                                                       | =IF(GLU_DiffMin>=GLU_dPmin,"every unloading valve opens at least "&FIXED(GLU_DiffMin,0)&" psi over its transfer pressure, against "&FIXED(GLU_dPmin,0)&" psi","a valve opens only "&FIXED(GLU_DiffMin,0)&" psi over its transfer pressure, under "&FIXED(GLU_dPmin,0)&" psi: lower the spacing factor or raise the kickoff pressure") |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 119 | Closing sequence check                                                                                                                                                                                    | =IF(GLU_FallMin>0,"PASS","WARN")                                                                                                                | =IF(GLU_FallMin>0,"each valve's surface closing pressure is at least "&FIXED(GLU_FallMin,0)&" psi above the next one's, so the valves close in turn","a valve's surface closing pressure is not above the next one's ("&FIXED(GLU_FallMin,0)&" psi): raise the drop per valve")                                                       |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 120 | Closing check                                                                                                                                                                                             | =IF(GLU_Margin>0,"PASS","FAIL")                                                                                                                 | =IF(GLU_Margin>0,"every unloading valve closes at the operating casing pressure, the closest by "&FIXED(GLU_Margin,0)&" psi","an unloading valve stays open at the operating casing pressure ("&FIXED(GLU_Margin,0)&" psi): raise the kickoff pressure or the drop per valve")                                                        |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |
| 121 | Spread check                                                                                                                                                                                              | =IF(GLU_SpreadTop<=GLU_SpreadMax,"PASS","WARN")                                                                                                 | =IF(GLU_SpreadTop<=GLU_SpreadMax,"the largest spread is "&FIXED(GLU_SpreadTop,0)&" psi, within "&FIXED(GLU_SpreadMax,0)&" psi","a valve spreads "&FIXED(GLU_SpreadTop,0)&" psi, over "&FIXED(GLU_SpreadMax,0)&" psi: a smaller port lowers R and the spread")                                                                         |                                     |                                                                                          |                                          |                                             |                                                                         |                                                             |                                                       |                                          |                                                                 |                                                    |                                   |                                                         |

## Names

| Name | RefersTo | Comment |
|------|----------|---------|
| GLU_Pko | $B$5 | Surface kickoff pressure, psi |
| GLU_Pso | $B$6 | Surface operating injection pressure, psi |
| GLU_Drop | $B$7 | Surface opening pressure drop per valve, psi |
| GLU_SG | $B$8 | Lift-gas specific gravity, air = 1 |
| GLU_Pwh | $B$9 | Flowing wellhead pressure, psi |
| GLU_Gs | $B$10 | Kill-fluid gradient, psi/ft |
| GLU_Ts | $B$11 | Surface temperature, °F |
| GLU_Tb | $B$12 | Temperature at the packer depth, °F |
| GLU_Dpk | $B$13 | Packer depth, ft |
| GLU_Dpoi | $B$14 | Point of injection (gl.injection.pressure), ft |
| GLU_Ptpoi | $B$15 | Tubing pressure at the point of injection, psi |
| GLU_Qgi | $B$16 | Design injection gas rate, Mscf/d |
| GLU_Fs | $B$18 | Spacing factor, share of Pso − Pwh added at the surface, % |
| GLU_dPmin | $B$19 | Least differential across a valve at transfer, psi |
| GLU_Cd | $B$21 | Port discharge coefficient |
| GLU_k | $B$22 | Lift-gas specific heat ratio, Cp/Cv |
| GLU_Ab | $B$23 | Valve bellows area, in² |
| GLU_St | $B$24 | Spring tension as a pressure (0: none), psi |
| GLU_SpreadMax | $B$25 | Largest valve spread accepted, psi |
| GLU_Gg | $B$26 | Casing gas gradient (type over to override), psi/ft |
| GLU_R | $B$27 | Port-to-bellows ratio R (type over to override) |
| GLU_Inputs | $B$5:$B$27 | Kickoff and operating pressures, the drop per valve, gas, wellhead, kill fluid, temperatures, depths and the design gas rate, the spacing factor and transfer differential, the port and valve, and the gas gradient and R |
| GLU_R0 | $B$30 | Rankine at 0 °F, °R |
| GLU_Track | $B$31 | Test-rack temperature, °F |
| GLU_PsiPpg | $B$32 | Gradient of a 1 ppg fluid, psi/ft per ppg |
| GLU_Ports | $A$37:$E$43 | Port sizes, diameter, area, R and Thornhill-Craver capacity at the point of injection |
| GLU_Dv1 | $C$51 | Depth of valve 1, ft |
| GLU_Ptr1 | $G$51 | Transfer pressure at valve 1, psia |
| GLU_Tro1 | $L$51 | Test-rack opening pressure of valve 1 at 60 °F, psia |
| GLU_Dv2 | $C$52 | Depth of valve 2, ft |
| GLU_Ptr2 | $G$52 | Transfer pressure at valve 2, psia |
| GLU_Tro2 | $L$52 | Test-rack opening pressure of valve 2 at 60 °F, psia |
| GLU_Dv3 | $C$53 | Depth of valve 3, ft |
| GLU_Ptr3 | $G$53 | Transfer pressure at valve 3, psia |
| GLU_Tro3 | $L$53 | Test-rack opening pressure of valve 3 at 60 °F, psia |
| GLU_Dv4 | $C$54 | Depth of valve 4, ft |
| GLU_Ptr4 | $G$54 | Transfer pressure at valve 4, psia |
| GLU_Tro4 | $L$54 | Test-rack opening pressure of valve 4 at 60 °F, psia |
| GLU_Dv5 | $C$55 | Depth of valve 5, ft |
| GLU_Ptr5 | $G$55 | Transfer pressure at valve 5, psia |
| GLU_Tro5 | $L$55 | Test-rack opening pressure of valve 5 at 60 °F, psia |
| GLU_Dv6 | $C$56 | Depth of valve 6, ft |
| GLU_Ptr6 | $G$56 | Transfer pressure at valve 6, psia |
| GLU_Tro6 | $L$56 | Test-rack opening pressure of valve 6 at 60 °F, psia |
| GLU_Dv7 | $C$57 | Depth of valve 7, ft |
| GLU_Ptr7 | $G$57 | Transfer pressure at valve 7, psia |
| GLU_Tro7 | $L$57 | Test-rack opening pressure of valve 7 at 60 °F, psia |
| GLU_Dv8 | $C$58 | Depth of valve 8, ft |
| GLU_Ptr8 | $G$58 | Transfer pressure at valve 8, psia |
| GLU_Tro8 | $L$58 | Test-rack opening pressure of valve 8 at 60 °F, psia |
| GLU_Dv9 | $C$59 | Depth of valve 9, ft |
| GLU_Ptr9 | $G$59 | Transfer pressure at valve 9, psia |
| GLU_Tro9 | $L$59 | Test-rack opening pressure of valve 9 at 60 °F, psia |
| GLU_Dv10 | $C$60 | Depth of valve 10, ft |
| GLU_Ptr10 | $G$60 | Transfer pressure at valve 10, psia |
| GLU_Tro10 | $L$60 | Test-rack opening pressure of valve 10 at 60 °F, psia |
| GLU_Valves | $A$51:$O$60 | Valve schedule: role, depth, temperature, opening at surface and depth, transfer pressure, dome, closing, spread, surface closing, test-rack opening, closing margin, transfer differential and the fall to the next valve's closing pressure |
| GLU_Tpc | $B$87 | Pseudo-critical temperature (Standing), °R |
| GLU_Ppc | $B$88 | Pseudo-critical pressure (Standing), psi |
| GLU_TPOI | $B$89 | Temperature at the point of injection, °F |
| GLU_Tcol | $B$90 | Gas-column average temperature, °F |
| GLU_G1 | $B$91 | Gas gradient, first pass, psi/ft |
| GLU_GgCalc | $B$92 | Gas gradient at the average pressure, psi/ft |
| GLU_KillPpg | $B$93 | Kill-fluid density for its gradient, ppg |
| GLU_P1op | $B$94 | Operating casing pressure at injection depth, psi |
| GLU_ApReq | $B$95 | Port area the design rate needs, in² |
| GLU_Small | $B$96 | Ports too small for the design rate |
| GLU_Port | $B$97 | Operating port |
| GLU_Ap | $B$98 | Operating port area, in² |
| GLU_Rport | $B$99 | R of the operating port |
| GLU_Qport | $B$100 | Gas the operating port passes, Mscf/d |
| GLU_Ptr0 | $B$102 | Transfer line at the surface, Pwh + Fs·(Pso − Pwh), psi |
| GLU_Gtr | $B$103 | Transfer line's gradient to the point of injection, psi/ft |
| GLU_Nu | $B$104 | Unloading valves |
| GLU_Dlast | $B$105 | Deepest mandrel, ft |
| GLU_D1 | $B$106 | Top valve depth, ft |
| GLU_Pvo1 | $B$107 | Top valve opening pressure at depth, psi |
| GLU_Pd1 | $B$108 | Top valve dome pressure at depth, psi |
| GLU_Pvc1 | $B$109 | Top valve closing pressure, psi |
| GLU_Spread1 | $B$110 | Top valve spread, psi |
| GLU_Ptro1 | $B$111 | Top valve test-rack opening at 60 °F, psi |
| GLU_Margin | $B$112 | Smallest closing margin at the operating pressure, psi |
| GLU_SpreadTop | $B$113 | Largest valve spread, psi |
| GLU_DiffMin | $B$114 | Smallest transfer differential, psi |
| GLU_FallMin | $B$115 | Smallest fall in surface closing pressure, valve to valve, psi |
| GLU_ReachCheck | $B$116 | Reach check verdict |
| GLU_ReachCheckNote | $C$116 | Reach check comment |
| GLU_PortCheck | $B$117 | Port check verdict |
| GLU_PortCheckNote | $C$117 | Port check comment |
| GLU_TransferCheck | $B$118 | Transfer check verdict |
| GLU_TransferCheckNote | $C$118 | Transfer check comment |
| GLU_SequenceCheck | $B$119 | Closing sequence check verdict |
| GLU_SequenceCheckNote | $C$119 | Closing sequence check comment |
| GLU_ClosingCheck | $B$120 | Closing check verdict |
| GLU_ClosingCheckNote | $C$120 | Closing check comment |
| GLU_SpreadCheck | $B$121 | Spread check verdict |
| GLU_SpreadCheckNote | $C$121 | Spread check comment |
| GLU_Results | $B$87:$B$121 | Pseudo-criticals, gas gradient, kill-fluid density, operating port, the transfer line, the valve count and the top valve's settings, and the reach, port, transfer, closing-sequence, closing and spread checks |
| GLU_Curve | $A$64:$H$84 | Gas-Lift Unloading Design |

---

## Related Blueprints
- [Gas-Lift Injection Pressure and Point of Injection](/blueprint/po.gl.injection.pressure.md)
- [Gas-Lift Valve Setting](/blueprint/po.gl.valve.setting.md)
- [Gas-Lift Valve Throughput](/blueprint/po.gl.valve.throughput.md)
- [Gas-Lift Allocation Across Four Wells by Equal Slope](/blueprint/po.gl.allocation.multiwell.md)
- [Compressor Staging and Power](/blueprint/po.sf.compressor.power.md)
- [Gas Well Tubing Sizing](/blueprint/po.vfp.tubing.sizing.md)

