---
cid: po.bp.frac.kgd.radial.geometry
hub: frac
tags: [frac, hydraulic-fracture, fracture-geometry, pkn, kgd, radial, penny-shaped, carter-leakoff, net-pressure, fluid-efficiency, height-containment]
facets: { discipline: completions, property: fracture-geometry, model: pkn, method-type: analytical }
title: Fracture Geometry Models Compared
summary: "Which 2D fracture model fits a treatment: one job pumped into PKN, KGD and radial, with the barriers deciding containment."
slug: po.frac.kgd.radial.geometry
type: worksheet
---

# Fracture Geometry Models Compared

## Description

Which 2D fracture model describes this treatment, and how different are the answers? You enter one job (rate, viscosity, pumping time, height, rock moduli and Carter leakoff) and the stress contrast to the barriers. You read off, side by side for PKN, KGD and radial geometries, the half-length or radius, the width at the wellbore and on average, the net pressure, the fracture volume and the fluid efficiency, and which model the height containment picks.

**Parameters:**
- **Treatment**: the rate per wing `FGC_Q`, the fluid viscosity `FGC_Mu`, the pumping time `FGC_Te`, the fracture height between the barriers `FGC_Hf`, Young's modulus `FGC_E`, Poisson's ratio `FGC_Nu`, Carter's leakoff coefficient `FGC_CL` and the opening-time factor `FGC_KL`
- **Height containment**: the stress contrast to the barriers above and below `FGC_Dsig`, and the height growth allowed before the fracture counts as uncontained `FGC_HMax`

**How to use it:** Take E and ν from the dipole sonic log or core, CL and the closure stress from a minifrac falloff (the DFIT G-Function Analysis sheet), and Δσ from a stress profile across the barriers. The sheet ships no synthetic data; its inputs are the screening sheet's. It pumps the job for the same time into the three classical geometries: PKN (height fixed, longer than high), KGD (height fixed, shorter than high) and radial (penny-shaped, no barriers). Each model's length at the pumping time comes from Nolte's material balance with Carter leakoff and the model's own width, solved by Newton passes written out as rows. Then the barriers decide: the height that PKN's net pressure would open between symmetric barriers of a given stress contrast (Simonson) says whether the fracture is contained, and the containment picks the model. Two charts draw each model's length and net pressure against pumping time.

**Method:** Per wing, the slurry pumped fills the fracture and leaks off through both faces: qi·t = A·(w̄ + 2·KL·CL·√t), with A = hf·L for PKN and KGD and π·R²/2 for the radial fracture (Nolte; Economides, Oligney and Valkó, Table 7-4). The average width w̄ is the model's at that length and the treatment rate: the PKN average of the PKN width at (qi, μ, L, E), the KGD average of the KGD width at (2qi, μ, L, hf, G), and the radial average of the radial width at (2qi, μ, R, G), with G = E/(2(1 + ν)). For a given length the balance is a quadratic in √t, √t = (c + √(c² + qa·w̄))/qa with c = KL·CL and qa = qi/A, so t(L) is explicit. Its inverse, the length at the pumping time, takes Newton passes in ln L: with A ∝ L^a and w̄ ∝ L^b (a = 1, b = ¼ for PKN; 1 and ½ for KGD; 2 and ¼ for radial), d ln t/d ln L = ((a + b)·w̄ + 2·a·c·√t)/(qa·t − c·√t), and each pass adds ln(te/t)/that slope. The passes start from each model's closed form without leakoff (Nordgren's PKN, Geertsma-de Klerk's KGD and radial), which the sheet also reports as the bound leakoff pulls the length below. The net pressures and volumes (both wings) are each model's own, and each efficiency is that volume over the slurry injected. For containment, a fracture of height hf between symmetric barriers of contrast Δσ opens to h = hf/sin(π/2·(1 − pnet/Δσ)) (Simonson, Abou-Sayed and Clifton), unbounded once pnet reaches Δσ; with PKN's net pressure, the fracture is contained when h/hf is within the height growth allowed. Contained and at least as long as high is PKN, contained and shorter is KGD, and uncontained is radial.

**Example:** The default is the job the Fracture Design Screening (Unified Fracture Design) sheet sizes: 15 bbl/min a wing of a 200 cp crosslinked gel into a 100 ft high fracture, E = 4 × 10⁶ psi, ν = 0.25, CL = 0.0015 ft/√min and KL = 1.5, pumped for 27.78 min, the time that sheet's PKN balance takes to its 600 ft design half-length. The barriers carry 1,500 psi more stress than the pay, and a quarter more height than hf still counts as contained.

G = 1.6 × 10⁶ psi and the slurry injected is 30 × 27.78 = 833.4 bbl. From the no-leakoff lengths (1,179, 656 and 348 ft) the balance closes to machine precision by the fourth pass. PKN reaches 600.0 ft at 0.311 in at the wellbore (0.183 in average), a net pressure of 553 psi and an efficiency of 39.2 %: the screening sheet's numbers. KGD reaches 441.5 ft, wider at 0.447 in, with a net pressure of only 90 psi and an efficiency of 55.2 %. The radial fracture reaches a radius of 207.7 ft (415 ft high), 0.243 in wide, at 164 psi and 31.3 %. PKN's 553 psi is 36.9 % of the 1,500 psi contrast, which opens the height to 1.195·hf = 119.5 ft, inside the 1.25 allowed, and the fracture is 6.0 times longer than high: the containment picks PKN.

## Validity

Two-dimensional models with a Newtonian fluid, a constant rate, a linear-elastic, homogeneous rock and Carter leakoff without spurt. The widths are the fixed-length widths each model gives at the treatment rate, which is how the screening sheet and Economides, Oligney and Valkó's design procedure use them; the closed-form time solutions (Nordgren's PKN, Geertsma-de Klerk's KGD and radial) agree only in their own limits, and the closed-form high-leakoff lengths need Carter's tD ≥ 1, while the default job sits near tD = 0.17, between the limits. PKN's net pressure is the one the containment uses, because PKN is the contained model: if that pressure breaks the barriers, the fracture isn't PKN. The Simonson relation is for symmetric barriers of equal stress and ignores the fracture toughness and the fluid's pressure drop in height; asymmetric barriers, several layers or a toughness contrast need a pseudo-3D or planar-3D model, which the sheet doesn't have. A power-law gel's apparent viscosity at the fracture's shear rate is the μ to type.

Named alternatives: the Fracture Design Screening (Unified Fracture Design) sheet sizes the job on PKN by unified fracture design, and the closed-form PKN, KGD and radial lengths without leakoff give the length a fluid without leakoff reaches.

## References

- Perkins, T.K. and Kern, L.R. (1961). "Widths of Hydraulic Fractures." *JPT* 13(9), 937–949; Nordgren, R.P. (1972). "Propagation of a Vertical Hydraulic Fracture." *SPEJ* 12(4), 306–314.
- Geertsma, J. and de Klerk, F. (1969). "A Rapid Method of Predicting Width and Extent of Hydraulically Induced Fractures." *JPT* 21(12), 1571–1581.
- Nolte, K.G. (1979). "Determination of Fracture Parameters from Fracturing Pressure Decline." SPE 8341; Nolte, K.G. and Smith, M.B. (1981). "Interpretation of Fracturing Pressures." *JPT* 33(9), 1767–1775.
- Simonson, E.R., Abou-Sayed, A.S. and Clifton, R.J. (1978). "Containment of Massive Hydraulic Fractures." *SPEJ* 18(1), 27–32.
- Economides, M.J., Oligney, R. and Valkó, P. (2002). *Unified Fracture Design*. Orsa Press, ch. 7 (Table 7-4, the material balance with the PKN width).
- Economides, M.J. and Nolte, K.G. (eds.) (2000). *Reservoir Stimulation*, 3rd ed. Wiley, ch. 6 "Mechanics of Hydraulic Fracturing".

## Functions used

`PO.FRAC.PKN.Width`, `PO.FRAC.PKN.Wavg`, `PO.FRAC.PKN.Pnet`, `PO.FRAC.PKN.Volume`, `PO.FRAC.PKN.Length.NoLoss`, `PO.FRAC.KGD.Width`, `PO.FRAC.KGD.Wavg`, `PO.FRAC.KGD.Pnet`, `PO.FRAC.KGD.Volume`, `PO.FRAC.KGD.Length.NoLoss`, `PO.FRAC.Radial.Width`, `PO.FRAC.Radial.Wavg`, `PO.FRAC.Radial.Pnet`, `PO.FRAC.Radial.Volume`, `PO.FRAC.Radial.Radius.NoLoss`, `PO.FRAC.Leakoff.Eff`, `PO.UnitConverter`

## Spreadsheet: FracGeometryModels

|    | A                                                                                                                                                                            | B                                                                                                                                                | C                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      | D                                                                                                 | E                                                                                                                               | F                                                                                                                                                                  | G                                                                               | H                                                                                                 | I                                                                                                                                                                   | J                                                                                     | K                                                                    | L                                                                                                   | M                                                                                                                                 |
|----|------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|---------------------------------------------------------------------------------------------------|---------------------------------------------------------------------------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------------------------|---------------------------------------------------------------------------------|---------------------------------------------------------------------------------------------------|---------------------------------------------------------------------------------------------------------------------------------------------------------------------|---------------------------------------------------------------------------------------|----------------------------------------------------------------------|-----------------------------------------------------------------------------------------------------|-----------------------------------------------------------------------------------------------------------------------------------|
| 1  | Fracture Geometry Models Compared                                                                                                                                            |                                                                                                                                                  | Petroleum Office                                                                                                                                                                                                                                                                                                                                                                                                                                                                       |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 2  | Blue cells on yellow are inputs. Type the treatment and the barriers' stress contrast; each model's geometry at the pumping time and the model the containment picks follow. |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 3  | Treatment (the Fracture Design Screening Job)                                                                                                                                |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 4  | Injection rate per wing, qi                                                                                                                                                  | 15                                                                                                                                               | bbl/min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 5  | Fracturing fluid viscosity, μ                                                                                                                                                | 200                                                                                                                                              | cp                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 6  | Pumping time, te                                                                                                                                                             | 27.78                                                                                                                                            | min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 7  | Fracture height between the barriers, hf                                                                                                                                     | 100                                                                                                                                              | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 8  | Young's modulus, E                                                                                                                                                           | 4000000                                                                                                                                          | psi                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 9  | Poisson's ratio, ν                                                                                                                                                           | 0.25                                                                                                                                             | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 10 | Carter leakoff coefficient, CL                                                                                                                                               | 0.0015                                                                                                                                           | ft/√min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 11 | Opening-time distribution factor, KL                                                                                                                                         | 1.5                                                                                                                                              | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 12 | Height Containment                                                                                                                                                           |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 13 | Stress contrast to the barriers above and below, Δσ                                                                                                                          | 1500                                                                                                                                             | psi                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 14 | Height growth allowed, opened height over hf                                                                                                                                 | 1.25                                                                                                                                             | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 16 | Common Terms                                                                                                                                                                 |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 17 | Shear modulus, G = E/(2·(1 + ν))                                                                                                                                             | =FGC_E/(2*(1+FGC_Nu))                                                                                                                            | psi                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 18 | Rate per wing in ft³/min                                                                                                                                                     | =PO.UnitConverter(FGC_Q,"bbl","ft3")                                                                                                             | ft³/min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 19 | Leakoff term of the balance, c = KL·CL                                                                                                                                       | =FGC_KL*FGC_CL                                                                                                                                   | ft/√min                                                                                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 20 | Slurry injected, both wings                                                                                                                                                  | =2*FGC_Q*FGC_Te                                                                                                                                  | bbl                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 21 | PKN: Height Fixed, Longer Than High                                                                                                                                          |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 22 | Half-length at the pumping time, L                                                                                                                                           | =B72                                                                                                                                             | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 23 | Width at the wellbore                                                                                                                                                        | =PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,FGC_PknL,FGC_E)                                                                                                  | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 24 | Average width                                                                                                                                                                | =PO.FRAC.PKN.Wavg(FGC_PknW)                                                                                                                      | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 25 | Net pressure                                                                                                                                                                 | =PO.FRAC.PKN.Pnet(FGC_PknW,FGC_Hf,FGC_E,FGC_Nu)                                                                                                  | psi                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 26 | Fracture volume, both wings                                                                                                                                                  | =2*PO.FRAC.PKN.Volume(FGC_PknW,FGC_Hf,FGC_PknL)                                                                                                  | bbl                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 27 | Fluid efficiency, η                                                                                                                                                          | =PO.FRAC.Leakoff.Eff(FGC_PknVol,FGC_Vi)                                                                                                          | %                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 28 | Half-length without leakoff (Nordgren)                                                                                                                                       | =B67                                                                                                                                             | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 29 | KGD: Height Fixed, Shorter Than High                                                                                                                                         |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 30 | Half-length at the pumping time, L                                                                                                                                           | =F72                                                                                                                                             | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 31 | Width at the wellbore                                                                                                                                                        | =PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,FGC_KgdL,FGC_Hf,FGC_G)                                                                                         | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 32 | Average width                                                                                                                                                                | =PO.FRAC.KGD.Wavg(FGC_KgdW)                                                                                                                      | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 33 | Net pressure                                                                                                                                                                 | =PO.FRAC.KGD.Pnet(FGC_KgdW,FGC_KgdL,FGC_G)                                                                                                       | psi                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 34 | Fracture volume, both wings                                                                                                                                                  | =PO.FRAC.KGD.Volume(FGC_KgdW,FGC_Hf,FGC_KgdL)                                                                                                    | bbl                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 35 | Fluid efficiency, η                                                                                                                                                          | =PO.FRAC.Leakoff.Eff(FGC_KgdVol,FGC_Vi)                                                                                                          | %                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 36 | Half-length without leakoff (Geertsma-de Klerk)                                                                                                                              | =F67                                                                                                                                             | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 37 | Radial: Penny-Shaped, Unconfined                                                                                                                                             |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 38 | Radius at the pumping time, R                                                                                                                                                | =J72                                                                                                                                             | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 39 | Width at the wellbore                                                                                                                                                        | =PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,FGC_RadR,FGC_G)                                                                                             | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 40 | Average width                                                                                                                                                                | =PO.FRAC.Radial.Wavg(FGC_RadW)                                                                                                                   | in                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 41 | Net pressure                                                                                                                                                                 | =PO.FRAC.Radial.Pnet(FGC_RadW,FGC_RadR,FGC_G,FGC_Nu)                                                                                             | psi                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 42 | Fracture volume                                                                                                                                                              | =PO.FRAC.Radial.Volume(FGC_RadW,FGC_RadR)                                                                                                        | bbl                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 43 | Fluid efficiency, η                                                                                                                                                          | =PO.FRAC.Leakoff.Eff(FGC_RadVol,FGC_Vi)                                                                                                          | %                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 44 | Radius without leakoff (Geertsma-de Klerk)                                                                                                                                   | =J67                                                                                                                                             | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 45 | Height of the radial fracture, 2·R                                                                                                                                           | =2*FGC_RadR                                                                                                                                      | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 46 | Height Containment and the Model It Picks                                                                                                                                    |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 47 | PKN net pressure over the stress contrast                                                                                                                                    | =FGC_PknPnet/FGC_Dsig                                                                                                                            | %                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 48 | Height opened over hf (Simonson; 0 is unbounded)                                                                                                                             | =IF(FGC_PRatio<1,1/SIN(PI()/2*(1-FGC_PRatio)),0)                                                                                                 | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 49 | Height the PKN net pressure opens                                                                                                                                            | =FGC_Hf*FGC_HRatio                                                                                                                               | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 50 | PKN half-length over the height, L/hf                                                                                                                                        | =FGC_PknL/FGC_Hf                                                                                                                                 | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 51 | Model the containment picks                                                                                                                                                  | =""&IF(AND(FGC_HRatio>0,FGC_HRatio<=FGC_HMax),IF(FGC_Aspect>=1,"PKN","KGD"),"Radial")                                                            |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 52 | Half-length (radius) of the model picked                                                                                                                                     | =IF(FGC_Model="PKN",FGC_PknL,IF(FGC_Model="KGD",FGC_KgdL,FGC_RadR))                                                                              | ft                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 53 | Fluid efficiency of the model picked                                                                                                                                         | =IF(FGC_Model="PKN",FGC_PknEta,IF(FGC_Model="KGD",FGC_KgdEta,FGC_RadEta))                                                                        | %                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 54 | Material balance check                                                                                                                                                       | =IF(OR(FGC_Q<=0,FGC_Te<=0,FGC_Hf<=0,FGC_CL<0),"FAIL",IF(MAX(ABS(D72/FGC_Te-1),ABS(H72/FGC_Te-1),ABS(L72/FGC_Te-1))<=FGC_SolveTol,"PASS","FAIL")) | =IF(OR(FGC_Q<=0,FGC_Te<=0,FGC_Hf<=0,FGC_CL<0),"the rate, the pumping time and the height must be positive, and CL not negative",IF(MAX(ABS(D72/FGC_Te-1),ABS(H72/FGC_Te-1),ABS(L72/FGC_Te-1))<=FGC_SolveTol,"each model's material balance closes at the pumping time after "&FGC_Passes&" Newton passes","a model's material balance doesn't close in the passes written; check the inputs"))                                                                                         |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 55 | Containment check                                                                                                                                                            | =IF(FGC_HMax<1,"FAIL",IF(FGC_Model="PKN","PASS",IF(FGC_Model="KGD","PASS","WARN")))                                                              | =IF(FGC_HMax<1,"the height growth allowed must be at least 1, no growth",IF(FGC_Model="PKN","PKN; the barriers hold the height to "&FIXED(FGC_Height,0)&" ft and the fracture is "&FIXED(FGC_Aspect,1)&" times longer than high",IF(FGC_Model="KGD","KGD; the barriers hold the height and the fracture is shorter than high, L/hf "&FIXED(FGC_Aspect,2),"radial; PKN's net pressure is "&FIXED(FGC_PRatio*100,0)&"% of the barriers' contrast, so the height grows past the limit"))) |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 57 | Calculation Constants                                                                                                                                                        |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 58 | Width exponent of PKN and radial, w ∝ L^¼                                                                                                                                    | 0.25                                                                                                                                             | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 59 | Width exponent of KGD, w ∝ L^½                                                                                                                                               | 0.5                                                                                                                                              | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 60 | Balance closed within this share of the pumping time                                                                                                                         | 0.000001                                                                                                                                         | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 61 | Newton passes written                                                                                                                                                        | 5                                                                                                                                                | —                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 63 | Length at the Pumping Time: Newton Passes on Nolte's Material Balance                                                                                                        |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 64 | Per wing, q·t = A·(w̄ + 2·KL·CL·√t), A = hf·L (PKN, KGD) or π·R²/2 (radial). t is explicit in L; each pass moves ln L by ln(te/t) over d ln t/d ln L.                        |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 65 | Pass 0 is each model's closed form without leakoff; the last row's lengths are the results above.                                                                            |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 66 | Pass (—)                                                                                                                                                                     | PKN L (ft)                                                                                                                                       | PKN w̄ (in)                                                                                                                                                                                                                                                                                                                                                                                                                                                                            | PKN t (min)                                                                                       | PKN slope                                                                                                                       | KGD L (ft)                                                                                                                                                         | KGD w̄ (in)                                                                     | KGD t (min)                                                                                       | KGD slope                                                                                                                                                           | Radial R (ft)                                                                         | Radial w̄ (in)                                                       | Radial t (min)                                                                                      | Radial slope                                                                                                                      |
| 67 | =0                                                                                                                                                                           | =PO.FRAC.PKN.Length.NoLoss(FGC_Q,FGC_Mu,FGC_Hf,FGC_G,FGC_Nu,FGC_Te)                                                                              | =PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B67,FGC_E))                                                                                                                                                                                                                                                                                                                                                                                                                           | =LET(qa,FGC_Qft/(FGC_Hf*B67),w,PO.UnitConverter(C67,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*B67),w,PO.UnitConverter(C67,"in","ft"),rt,SQRT(D67),((1+FGC_Quarter)*w+2*1*FGC_C*rt)/(qa*D67-FGC_C*rt)) | =PO.FRAC.KGD.Length.NoLoss(2*FGC_Q,FGC_Mu,FGC_Hf,FGC_G,FGC_Te)                                                                                                     | =PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,F67,FGC_Hf,FGC_G))           | =LET(qa,FGC_Qft/(FGC_Hf*F67),w,PO.UnitConverter(G67,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*F67),w,PO.UnitConverter(G67,"in","ft"),rt,SQRT(H67),((1+FGC_Half)*w+2*1*FGC_C*rt)/(qa*H67-FGC_C*rt))                                        | =PO.FRAC.Radial.Radius.NoLoss(2*FGC_Q,FGC_Mu,FGC_G,FGC_Te)                            | =PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,J67,FGC_G)) | =LET(qa,2*FGC_Qft/(PI()*J67^2),w,PO.UnitConverter(K67,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,2*FGC_Qft/(PI()*J67^2),w,PO.UnitConverter(K67,"in","ft"),rt,SQRT(L67),((2+FGC_Quarter)*w+2*2*FGC_C*rt)/(qa*L67-FGC_C*rt)) |
| 68 | =1                                                                                                                                                                           | =B67*EXP(LN(FGC_Te/D67)/E67)                                                                                                                     | =PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B68,FGC_E))                                                                                                                                                                                                                                                                                                                                                                                                                           | =LET(qa,FGC_Qft/(FGC_Hf*B68),w,PO.UnitConverter(C68,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*B68),w,PO.UnitConverter(C68,"in","ft"),rt,SQRT(D68),((1+FGC_Quarter)*w+2*1*FGC_C*rt)/(qa*D68-FGC_C*rt)) | =F67*EXP(LN(FGC_Te/H67)/I67)                                                                                                                                       | =PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,F68,FGC_Hf,FGC_G))           | =LET(qa,FGC_Qft/(FGC_Hf*F68),w,PO.UnitConverter(G68,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*F68),w,PO.UnitConverter(G68,"in","ft"),rt,SQRT(H68),((1+FGC_Half)*w+2*1*FGC_C*rt)/(qa*H68-FGC_C*rt))                                        | =J67*EXP(LN(FGC_Te/L67)/M67)                                                          | =PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,J68,FGC_G)) | =LET(qa,2*FGC_Qft/(PI()*J68^2),w,PO.UnitConverter(K68,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,2*FGC_Qft/(PI()*J68^2),w,PO.UnitConverter(K68,"in","ft"),rt,SQRT(L68),((2+FGC_Quarter)*w+2*2*FGC_C*rt)/(qa*L68-FGC_C*rt)) |
| 69 | =2                                                                                                                                                                           | =B68*EXP(LN(FGC_Te/D68)/E68)                                                                                                                     | =PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B69,FGC_E))                                                                                                                                                                                                                                                                                                                                                                                                                           | =LET(qa,FGC_Qft/(FGC_Hf*B69),w,PO.UnitConverter(C69,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*B69),w,PO.UnitConverter(C69,"in","ft"),rt,SQRT(D69),((1+FGC_Quarter)*w+2*1*FGC_C*rt)/(qa*D69-FGC_C*rt)) | =F68*EXP(LN(FGC_Te/H68)/I68)                                                                                                                                       | =PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,F69,FGC_Hf,FGC_G))           | =LET(qa,FGC_Qft/(FGC_Hf*F69),w,PO.UnitConverter(G69,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*F69),w,PO.UnitConverter(G69,"in","ft"),rt,SQRT(H69),((1+FGC_Half)*w+2*1*FGC_C*rt)/(qa*H69-FGC_C*rt))                                        | =J68*EXP(LN(FGC_Te/L68)/M68)                                                          | =PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,J69,FGC_G)) | =LET(qa,2*FGC_Qft/(PI()*J69^2),w,PO.UnitConverter(K69,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,2*FGC_Qft/(PI()*J69^2),w,PO.UnitConverter(K69,"in","ft"),rt,SQRT(L69),((2+FGC_Quarter)*w+2*2*FGC_C*rt)/(qa*L69-FGC_C*rt)) |
| 70 | =3                                                                                                                                                                           | =B69*EXP(LN(FGC_Te/D69)/E69)                                                                                                                     | =PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B70,FGC_E))                                                                                                                                                                                                                                                                                                                                                                                                                           | =LET(qa,FGC_Qft/(FGC_Hf*B70),w,PO.UnitConverter(C70,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*B70),w,PO.UnitConverter(C70,"in","ft"),rt,SQRT(D70),((1+FGC_Quarter)*w+2*1*FGC_C*rt)/(qa*D70-FGC_C*rt)) | =F69*EXP(LN(FGC_Te/H69)/I69)                                                                                                                                       | =PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,F70,FGC_Hf,FGC_G))           | =LET(qa,FGC_Qft/(FGC_Hf*F70),w,PO.UnitConverter(G70,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*F70),w,PO.UnitConverter(G70,"in","ft"),rt,SQRT(H70),((1+FGC_Half)*w+2*1*FGC_C*rt)/(qa*H70-FGC_C*rt))                                        | =J69*EXP(LN(FGC_Te/L69)/M69)                                                          | =PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,J70,FGC_G)) | =LET(qa,2*FGC_Qft/(PI()*J70^2),w,PO.UnitConverter(K70,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,2*FGC_Qft/(PI()*J70^2),w,PO.UnitConverter(K70,"in","ft"),rt,SQRT(L70),((2+FGC_Quarter)*w+2*2*FGC_C*rt)/(qa*L70-FGC_C*rt)) |
| 71 | =4                                                                                                                                                                           | =B70*EXP(LN(FGC_Te/D70)/E70)                                                                                                                     | =PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B71,FGC_E))                                                                                                                                                                                                                                                                                                                                                                                                                           | =LET(qa,FGC_Qft/(FGC_Hf*B71),w,PO.UnitConverter(C71,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*B71),w,PO.UnitConverter(C71,"in","ft"),rt,SQRT(D71),((1+FGC_Quarter)*w+2*1*FGC_C*rt)/(qa*D71-FGC_C*rt)) | =F70*EXP(LN(FGC_Te/H70)/I70)                                                                                                                                       | =PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,F71,FGC_Hf,FGC_G))           | =LET(qa,FGC_Qft/(FGC_Hf*F71),w,PO.UnitConverter(G71,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*F71),w,PO.UnitConverter(G71,"in","ft"),rt,SQRT(H71),((1+FGC_Half)*w+2*1*FGC_C*rt)/(qa*H71-FGC_C*rt))                                        | =J70*EXP(LN(FGC_Te/L70)/M70)                                                          | =PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,J71,FGC_G)) | =LET(qa,2*FGC_Qft/(PI()*J71^2),w,PO.UnitConverter(K71,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,2*FGC_Qft/(PI()*J71^2),w,PO.UnitConverter(K71,"in","ft"),rt,SQRT(L71),((2+FGC_Quarter)*w+2*2*FGC_C*rt)/(qa*L71-FGC_C*rt)) |
| 72 | =5                                                                                                                                                                           | =B71*EXP(LN(FGC_Te/D71)/E71)                                                                                                                     | =PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B72,FGC_E))                                                                                                                                                                                                                                                                                                                                                                                                                           | =LET(qa,FGC_Qft/(FGC_Hf*B72),w,PO.UnitConverter(C72,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*B72),w,PO.UnitConverter(C72,"in","ft"),rt,SQRT(D72),((1+FGC_Quarter)*w+2*1*FGC_C*rt)/(qa*D72-FGC_C*rt)) | =F71*EXP(LN(FGC_Te/H71)/I71)                                                                                                                                       | =PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,F72,FGC_Hf,FGC_G))           | =LET(qa,FGC_Qft/(FGC_Hf*F72),w,PO.UnitConverter(G72,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,FGC_Qft/(FGC_Hf*F72),w,PO.UnitConverter(G72,"in","ft"),rt,SQRT(H72),((1+FGC_Half)*w+2*1*FGC_C*rt)/(qa*H72-FGC_C*rt))                                        | =J71*EXP(LN(FGC_Te/L71)/M71)                                                          | =PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,J72,FGC_G)) | =LET(qa,2*FGC_Qft/(PI()*J72^2),w,PO.UnitConverter(K72,"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =LET(qa,2*FGC_Qft/(PI()*J72^2),w,PO.UnitConverter(K72,"in","ft"),rt,SQRT(L72),((2+FGC_Quarter)*w+2*2*FGC_C*rt)/(qa*L72-FGC_C*rt)) |
| 75 | The Three Models Side by Side                                                                                                                                                |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 76 | Model                                                                                                                                                                        | Length (ft)                                                                                                                                      | Wellbore w (in)                                                                                                                                                                                                                                                                                                                                                                                                                                                                        | Average w (in)                                                                                    | Net pressure (psi)                                                                                                              | Volume (bbl)                                                                                                                                                       | Efficiency (%)                                                                  | No leakoff (ft)                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 77 | PKN                                                                                                                                                                          | =FGC_PknL                                                                                                                                        | =FGC_PknW                                                                                                                                                                                                                                                                                                                                                                                                                                                                              | =FGC_PknWavg                                                                                      | =FGC_PknPnet                                                                                                                    | =FGC_PknVol                                                                                                                                                        | =FGC_PknEta                                                                     | =FGC_PknNoLoss                                                                                    |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 78 | KGD                                                                                                                                                                          | =FGC_KgdL                                                                                                                                        | =FGC_KgdW                                                                                                                                                                                                                                                                                                                                                                                                                                                                              | =FGC_KgdWavg                                                                                      | =FGC_KgdPnet                                                                                                                    | =FGC_KgdVol                                                                                                                                                        | =FGC_KgdEta                                                                     | =FGC_KgdNoLoss                                                                                    |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 79 | Radial                                                                                                                                                                       | =FGC_RadR                                                                                                                                        | =FGC_RadW                                                                                                                                                                                                                                                                                                                                                                                                                                                                              | =FGC_RadWavg                                                                                      | =FGC_RadPnet                                                                                                                    | =FGC_RadVol                                                                                                                                                        | =FGC_RadEta                                                                     | =FGC_RadNoLoss                                                                                    |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 81 | Growth With Pumping Time, Each Model                                                                                                                                         |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 82 | How to use it: E and ν from the logs or core, CL and closure from a minifrac (the DFIT G-Function sheet), Δσ from a stress profile.                                          |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 83 | Each model at a tenth to 1.5 times its length at te: PKN's net pressure rises as it grows and KGD's and radial's fall (Nolte-Smith).                                         |                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                   |                                                                                                                                 |                                                                                                                                                                    |                                                                                 |                                                                                                   |                                                                                                                                                                     |                                                                                       |                                                                      |                                                                                                     |                                                                                                                                   |
| 84 | Share of L (—)                                                                                                                                                               | PKN L (ft)                                                                                                                                       | PKN t (min)                                                                                                                                                                                                                                                                                                                                                                                                                                                                            | PKN pnet (psi)                                                                                    | KGD L (ft)                                                                                                                      | KGD t (min)                                                                                                                                                        | KGD pnet (psi)                                                                  | Radial R (ft)                                                                                     | Radial t (min)                                                                                                                                                      | Radial pnet (psi)                                                                     |                                                                      |                                                                                                     |                                                                                                                                   |
| 85 | =1/10                                                                                                                                                                        | =A85*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B85),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B85,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B85,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A85*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E85),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E85,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E85,FGC_Hf,FGC_G),E85,FGC_G) | =A85*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H85^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H85,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H85,FGC_G),H85,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 86 | =2/10                                                                                                                                                                        | =A86*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B86),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B86,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B86,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A86*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E86),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E86,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E86,FGC_Hf,FGC_G),E86,FGC_G) | =A86*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H86^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H86,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H86,FGC_G),H86,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 87 | =3/10                                                                                                                                                                        | =A87*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B87),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B87,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B87,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A87*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E87),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E87,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E87,FGC_Hf,FGC_G),E87,FGC_G) | =A87*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H87^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H87,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H87,FGC_G),H87,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 88 | =4/10                                                                                                                                                                        | =A88*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B88),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B88,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B88,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A88*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E88),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E88,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E88,FGC_Hf,FGC_G),E88,FGC_G) | =A88*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H88^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H88,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H88,FGC_G),H88,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 89 | =5/10                                                                                                                                                                        | =A89*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B89),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B89,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B89,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A89*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E89),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E89,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E89,FGC_Hf,FGC_G),E89,FGC_G) | =A89*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H89^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H89,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H89,FGC_G),H89,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 90 | =6/10                                                                                                                                                                        | =A90*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B90),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B90,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B90,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A90*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E90),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E90,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E90,FGC_Hf,FGC_G),E90,FGC_G) | =A90*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H90^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H90,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H90,FGC_G),H90,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 91 | =7/10                                                                                                                                                                        | =A91*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B91),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B91,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B91,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A91*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E91),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E91,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E91,FGC_Hf,FGC_G),E91,FGC_G) | =A91*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H91^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H91,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H91,FGC_G),H91,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 92 | =8/10                                                                                                                                                                        | =A92*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B92),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B92,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B92,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A92*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E92),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E92,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E92,FGC_Hf,FGC_G),E92,FGC_G) | =A92*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H92^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H92,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H92,FGC_G),H92,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 93 | =9/10                                                                                                                                                                        | =A93*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B93),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B93,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B93,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A93*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E93),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E93,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E93,FGC_Hf,FGC_G),E93,FGC_G) | =A93*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H93^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H93,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H93,FGC_G),H93,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 94 | =10/10                                                                                                                                                                       | =A94*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B94),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B94,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B94,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A94*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E94),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E94,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E94,FGC_Hf,FGC_G),E94,FGC_G) | =A94*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H94^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H94,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H94,FGC_G),H94,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 95 | =11/10                                                                                                                                                                       | =A95*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B95),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B95,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B95,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A95*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E95),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E95,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E95,FGC_Hf,FGC_G),E95,FGC_G) | =A95*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H95^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H95,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H95,FGC_G),H95,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 96 | =12/10                                                                                                                                                                       | =A96*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B96),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B96,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B96,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A96*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E96),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E96,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E96,FGC_Hf,FGC_G),E96,FGC_G) | =A96*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H96^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H96,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H96,FGC_G),H96,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 97 | =13/10                                                                                                                                                                       | =A97*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B97),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B97,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B97,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A97*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E97),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E97,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E97,FGC_Hf,FGC_G),E97,FGC_G) | =A97*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H97^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H97,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H97,FGC_G),H97,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 98 | =14/10                                                                                                                                                                       | =A98*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B98),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B98,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B98,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A98*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E98),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E98,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E98,FGC_Hf,FGC_G),E98,FGC_G) | =A98*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H98^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H98,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H98,FGC_G),H98,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |
| 99 | =15/10                                                                                                                                                                       | =A99*FGC_PknL                                                                                                                                    | =LET(qa,FGC_Qft/(FGC_Hf*B99),w,PO.UnitConverter(PO.FRAC.PKN.Wavg(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B99,FGC_E)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2)                                                                                                                                                                                                                                                                                                                              | =PO.FRAC.PKN.Pnet(PO.FRAC.PKN.Width(FGC_Q,FGC_Mu,B99,FGC_E),FGC_Hf,FGC_E,FGC_Nu)                  | =A99*FGC_KgdL                                                                                                                   | =LET(qa,FGC_Qft/(FGC_Hf*E99),w,PO.UnitConverter(PO.FRAC.KGD.Wavg(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E99,FGC_Hf,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.KGD.Pnet(PO.FRAC.KGD.Width(2*FGC_Q,FGC_Mu,E99,FGC_Hf,FGC_G),E99,FGC_G) | =A99*FGC_RadR                                                                                     | =LET(qa,2*FGC_Qft/(PI()*H99^2),w,PO.UnitConverter(PO.FRAC.Radial.Wavg(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H99,FGC_G)),"in","ft"),((FGC_C+SQRT(FGC_C^2+qa*w))/qa)^2) | =PO.FRAC.Radial.Pnet(PO.FRAC.Radial.Width(2*FGC_Q,FGC_Mu,H99,FGC_G),H99,FGC_G,FGC_Nu) |                                                                      |                                                                                                     |                                                                                                                                   |

## Names

| Name | RefersTo | Comment |
|------|----------|---------|
| FGC_Q | $B$4 | Injection rate per wing, qi, bbl/min |
| FGC_Mu | $B$5 | Fracturing fluid viscosity, μ, cp |
| FGC_Te | $B$6 | Pumping time, te, min |
| FGC_Hf | $B$7 | Fracture height between the barriers, hf, ft |
| FGC_E | $B$8 | Young's modulus, E, psi |
| FGC_Nu | $B$9 | Poisson's ratio, ν |
| FGC_CL | $B$10 | Carter leakoff coefficient, CL, ft/√min |
| FGC_KL | $B$11 | Opening-time distribution factor, KL |
| FGC_Dsig | $B$13 | Stress contrast to the barriers above and below, Δσ, psi |
| FGC_HMax | $B$14 | Height growth allowed, opened height over hf |
| FGC_Inputs | $B$4:$B$14 | The treatment (rate, fluid, pumping time, height, rock and leakoff) and the barriers' stress contrast with the height growth allowed |
| FGC_G | $B$17 | Shear modulus, G = E/(2·(1 + ν)), psi |
| FGC_Qft | $B$18 | Rate per wing in ft³/min, ft³/min |
| FGC_C | $B$19 | Leakoff term of the balance, c = KL·CL, ft/√min |
| FGC_Vi | $B$20 | Slurry injected, both wings, bbl |
| FGC_PknL | $B$22 | Half-length at the pumping time, L, ft |
| FGC_PknW | $B$23 | Width at the wellbore, in |
| FGC_PknWavg | $B$24 | Average width, in |
| FGC_PknPnet | $B$25 | Net pressure, psi |
| FGC_PknVol | $B$26 | Fracture volume, both wings, bbl |
| FGC_PknEta | $B$27 | Fluid efficiency, η, % |
| FGC_PknNoLoss | $B$28 | Half-length without leakoff (Nordgren), ft |
| FGC_KgdL | $B$30 | Half-length at the pumping time, L, ft |
| FGC_KgdW | $B$31 | Width at the wellbore, in |
| FGC_KgdWavg | $B$32 | Average width, in |
| FGC_KgdPnet | $B$33 | Net pressure, psi |
| FGC_KgdVol | $B$34 | Fracture volume, both wings, bbl |
| FGC_KgdEta | $B$35 | Fluid efficiency, η, % |
| FGC_KgdNoLoss | $B$36 | Half-length without leakoff (Geertsma-de Klerk), ft |
| FGC_RadR | $B$38 | Radius at the pumping time, R, ft |
| FGC_RadW | $B$39 | Width at the wellbore, in |
| FGC_RadWavg | $B$40 | Average width, in |
| FGC_RadPnet | $B$41 | Net pressure, psi |
| FGC_RadVol | $B$42 | Fracture volume, bbl |
| FGC_RadEta | $B$43 | Fluid efficiency, η, % |
| FGC_RadNoLoss | $B$44 | Radius without leakoff (Geertsma-de Klerk), ft |
| FGC_RadHeight | $B$45 | Height of the radial fracture, 2·R, ft |
| FGC_PRatio | $B$47 | PKN net pressure over the stress contrast, % |
| FGC_HRatio | $B$48 | Height opened over hf (Simonson; 0 is unbounded) |
| FGC_Height | $B$49 | Height the PKN net pressure opens, ft |
| FGC_Aspect | $B$50 | PKN half-length over the height, L/hf |
| FGC_Model | $B$51 | Model the containment picks |
| FGC_PickL | $B$52 | Half-length (radius) of the model picked, ft |
| FGC_PickEta | $B$53 | Fluid efficiency of the model picked, % |
| FGC_SolveCheck | $B$54 | Material balance check verdict |
| FGC_SolveCheckNote | $C$54 | Material balance check comment |
| FGC_ModelCheck | $B$55 | Containment check verdict |
| FGC_ModelCheckNote | $C$55 | Containment check comment |
| FGC_Results | $B$17:$B$55 | The common terms, each model's length, widths, net pressure, volume and efficiency, the height containment, the model picked, and the two checks |
| FGC_Quarter | $B$58 | Width exponent of PKN and radial, w ∝ L^¼ |
| FGC_Half | $B$59 | Width exponent of KGD, w ∝ L^½ |
| FGC_SolveTol | $B$60 | Balance closed within this share of the pumping time |
| FGC_Passes | $B$61 | Newton passes written |
| FGC_Solver | $A$67:$M$72 | Newton passes 0 to 5: each model's length (radius), average width, the time the balance gives for it, and d ln t/d ln L |
| FGC_Compare | $A$77:$H$79 | One row a model: length (radius), widths, net pressure, volume, efficiency and the no-leakoff length |
| FGC_Growth | $A$85:$J$99 | Each model at 0.1 to 1.5 times its length at te: the length (radius), the pumping time to reach it, and its net pressure |

---

## Related Blueprints
- [Fracture Design Screening (Unified Fracture Design)](/blueprint/po.frac.design.screening.md)
- [Fracture Pump Schedule (Nolte Pad and Proppant Ramp)](/blueprint/po.frac.pump.schedule.md)
- [DFIT G-Function Analysis](/blueprint/po.frac.dfit.gfunction.md)
- [Proppant Settling and Transport](/blueprint/po.frac.proppant.settling.md)
- [Tubing Stress and Movement](/blueprint/po.de.tubing.stress.md)
- [Decline and Flow-Regime Diagnostics](/blueprint/po.dca.diagnostics.analysis.md)

